Keysight Technologies N9040B Installations- und Betriebshandbuch

Option CRP Arbitrary IF Out

Option ALV Log Video Out

Keysight Technologies

UXA Signal Analyzer

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9040-90010

Edition

Edition 1, February 2017

Supersedes January 2015

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9040-90010 3

Option CRP or ALV Installation Kit

Products Affected: UXA N9040B

UXA N9041B

Serial Numbers: All

Options

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysight

(X) Customer

Estimated Installation Time:

Estimated Adjustment and Verification Time:

0.5 Hours

4Installation Note N9040-90010

Option CRP or ALV Installation Kit

Introduction

This kit contains all of the instructions required to install Option CRP or ALV on a UXA X-Series

signal analyzer.

The rear panel AUX IF OUT port is present on all UXA signal analyzers, however each of the possible

output signal choices require a license.

Contents

1. At the time of manufacture the hardware related to this option was fully adjusted and the

option performance was verified to be within its warranted specifications. Within one year of the

initial calibration date of the instrument this option is fully calibrated with no further adjustment

or verification testing.

To determine the initial calibration date, locate the original calibration certificate that was

shipped with the instrument at the time of purchase. The Date of Calibration is printed on the

original calibration certificate.

To ensure that this newly installed option has been installed properly, the procedure that follows

includes a functional check.

2. The latest revision of the X-Series signal analyzer software may be downloaded from:

http://www.keysight.com/find/Xseries_software

3. This option is licensed for one instrument model/serial number combination. The license key

will only install on the designated instrument.

Quantity Description Part Number

1 Installation Note This note

1 Option Upgrade Entitlement Certificate 5964-5178

Installation Note N9040-90010 5

Option CRP or ALV Installation Kit

Tools Required for Installation

— Personal computer with internet access and USB port

— USB storage device with > 2 GB free memory

Tools Required for Manual Operation Verification

For Option CRP

— Spectrum Analyzer capable of measuring a 322.5 MHz signal at -40 dBm

— Test cable, sma or 3.5 mm connectors

— Adapters as needed to connect the cable between the spectrum analyzer and sma AUX IF OUT

port on the rear panel of the UXA analyzer

For Option ALV

— Signal source capable of providing pulse output above 200 MHz

— Oscilloscope

— Test cable, BNC

— BNC (f) to sma (m) adapter to connect the cable between the oscilloscope and sma AUX IF OUT

port on the rear panel of the UXA analyzer

6Installation Note N9040-90010

Option CRP or ALV Installation Kit

Installation Procedure over USB

1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.

2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the

Certificate.

3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an

attached License File.

4. Locate a USB storage device. Perform a virus scan on this device before use.

5. Save the License File to the root directory of the USB Storage Device.

6. Connect the USB Storage Device to the signal analyzer USB port. Windows will detect the new

hardware and may display the configuration menu shown in Figure 1. This menu may be

configured according to your preferences.

Figure 1 USB Storage Device Configuration Menu

7. The signal analyzer will automatically consume the License File. (This may take a few minutes)

When the License File is consumed the Keysight License Manager will display a “Successful

License Installation” message as shown in Figure 2.

Figure 2 Successful License Installation

Installation Note N9040-90010 7

Option CRP or ALV Installation Kit

Alternate Installation Procedure

The License File can be manually installed over USB or LAN by placing the license file in the

following folder on the signal analyzer

C:\Program Files\Agilent\licensing

Verify the Installation

1. Cycle the power on the signal analyzer.

2. Press System, Show System to display a list of installed options.

3. Verify that the newly installed option appears on the list.

8Installation Note N9040-90010

Option CRP or ALV Installation Kit

Manually Verify Operation

Option CRP, Arbitrary IF Output

1. Preset the UXA analyzer. Assure mode is Spectrum Analyzer.

2. Display the 50 MHz calibrator signal. Press Input/Output, RF Calibrator, 50 MHz. Press FREQ,

Center Frequency. Key in 50 MHz. Press Swept Span, Zero Span to toggle to Zero Span. You

should see a flat line across the display at -25 dBm.

3. Enable Option CRP. Press Input/Output, Output, Aux IF Out. Select Arbitrary IF. Press Arbitrary

IF Freq. Set the Arbitrary IF Out frequency to 70 MHz using the key pad.

4. Connect a spectrum analyzer to the rear panel Aux IF Out port using test cable and appropriate

adapters.

Spectrum analyzer settings:

Center frequency: 70 MHz

Span: 1 MHz

Bandwidth: 100 kHz

The spectrum analyzer should display a −33 dBm ±5 dB signal

Installation Note N9040-90010 9

Option CRP or ALV Installation Kit

Option ALV, Fast Log Video

1. Preset the UXA analyzer. Assure mode is Spectrum Analyzer.

2. Enable Option ALV. Press Input/Output, Output, Aux IF Out, Fast Log Video.

3. Connect a signal source configured for a pulse output to the UXA analyzer RF input port. The

frequency of the pulse should be above 200 MHz. Example settings are:

Pulse frequency: 400 MHz

Amplitude: −20 dBm

Pulse period: 80 μsec

Pulse width: 40 μsec

4. UXA analyzer settings:

Center frequency: 400 MHz

Span: 0 Hz

Bandwidth: 3 MHz

5. Connect an oscilloscope to the UXA analyzer rear panel Aux IF Out port.

Oscilloscope settings:

500 mV/div

10 μsec/div

Adjust oscilloscope to view the pulse on the oscilloscope. Pulse should measure

approximately 1.3 VP-P

10 Installation Note N9040-90010

Option CRP or ALV Installation Kit

Utilities, Adjustments, and Performance Verification Tests

Calibration Software and specified test equipment is required to perform the adjustments, and can

be used to automate the performance verification testing. Information on how to obtain this

software can be found at

http://www.keysight.com/find/calibrationsoftware

Utilities Required

None

Adjustments Required

None

Performance Testing Required

None

A full calibration is required to assure the instrument meets all specifications

The end user must ultimately determine whether they want a full calibration to be performed after

the installation of this upgrade or not. If a full calibration is required, arrangements regarding the

level of calibration must be made between the end user and the calibration provider.

For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your

local Keysight office access the following URL, or if in the United States, call the following

telephone number:

http://www.keysight.com/find/assist

1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)

Andere Handbücher für N9040B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Keysight Technologies Messgerät Handbücher

Keysight Technologies

Keysight Technologies B1500A Bedienungsanleitung

Keysight Technologies

Keysight Technologies B1505A Bedienungsanleitung

Keysight Technologies

Keysight Technologies N9030B Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies E5072A Bedienungsanleitung

Keysight Technologies

Keysight Technologies N9030B Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies N9029AV01-V19 Bedienungsanleitung

Keysight Technologies

Keysight Technologies PNA Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies N9020A Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies 5061B Bedienungsanleitung

Keysight Technologies

Keysight Technologies E4981A Betriebsanleitung

Keysight Technologies

Keysight Technologies 86120B Bedienungsanleitung

Keysight Technologies

Keysight Technologies FieldFox N9927-90002 Bedienungsanleitung

Keysight Technologies

Keysight Technologies N5224A Bedienungsanleitung

Keysight Technologies

Keysight Technologies LTE Installationshandbuch

Keysight Technologies

Keysight Technologies E5072A Bedienungsanleitung

Keysight Technologies

Keysight Technologies EXA N9010B Kurzanleitung

Keysight Technologies

Keysight Technologies U1731C Bedienungsanleitung

Keysight Technologies

Keysight Technologies N5252A Bedienungsanleitung

Keysight Technologies

Keysight Technologies M937 A Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies N5245-60106 Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies U5309A Benutzerhandbuch

Keysight Technologies

Keysight Technologies N524 A Series Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies N9010B Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies N9030B Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung