Keysight Technologies N9030B Installations- und Betriebshandbuch
Keysight Technologies
N9030B Signal Analyzer
Option BBA
Analog Baseband IQ Inputs
Upgrade Kit
Installation Note
Notices
© Copyright 2016 - 2017 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
N9030-90077
Edition
Edition 1, March 2017
Supersedes February 2016
Printed in USA/Malaysia
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403
Installation Note N9030-90077 3
Option BBA, Analog Baseband I/Q Inputs Upgrade Kit
Option BBA, Analog Baseband I/Q Inputs Upgrade Kit
Products Affected: N9030B, PXA Signal Analyzer with Options 503, 508,
513, or 526
Serial Numbers: All
Option BBA
To Be Performed By: (X) Keysight Service Center
(X) Personnel Qualified by Keysight
( ) Customer
Estimated Installation Time:
Estimated Adjustment Time:
Estimated Verification Timea:
a.To ensure that this newly installed option is functioning properly, the procedure that follows includes the
requirement of performing certain adjustments and performance verification tests. However, the completion of
these tests does not guarantee that the instrument meets all advertised specifications.
Software and test equipment is required for making adjustments and for performance verification testing.
Information on how to obtain this software can be found at:
www.keysight.com/find/calibrationsoftware
While Keysight does recommend that a full calibration be performed after the installation of this upgrade, the
end user must ultimately determine whether they want this service or not. If a full calibration is required,
arrangements regarding the level of calibration must be made between the end user and the calibration
provider.
3.0 Hours
0.5 Hours
3.0 Hours
4Installation Note N9030-90077
Option BBA, Analog Baseband I/Q Inputs Upgrade Kit
Introduction
This kit provides all parts and instructions necessary to install Option BBA, Analog Baseband I/Q
Input, into the Keysight N9030B with frequency range 26.5 GHz and below.
1. This upgrade kit is not compatible with N9030B PXA signal analyzers with any
of the following options currently installed:
N9030B-B5X - 510 MHz Analysis Bandwidth
N9030B-544 - Frequency Range, 3 Hz to 44 GHz
N9030B-550 - Frequency Range, 3 Hz to 50 GHz
2. This upgrade kit installation requires that you re-install instrument software.
The latest revision of the PXA Signal Analyzer software may be downloaded
from
http:/www.keysight.com/find/xseries_software
The instrument software must be installed AFTER the hardware in the kit is
installed. Follow the procedure in this document for redeeming and installing
the option upgrade license key.
3. The option is licensed for one instrument model/serial number combination.
The license key will only install on the designated instrument.
Installation Note N9030-90077 5
Option BBA, Analog Baseband I/Q Inputs Upgrade Kit
Installation Kit Parts List
Quantity Description Keysight Part Number
1 BBIQ Main Board N9020-60093
1 LED Board N9020-63095
1 BBIQ Interface Board N9020-60094
1 LED Board Overlay, Bottom N9020-80166
1 LED Board Overlay, Top N9020-80163
1Cable, Flex Ribbona
a.Only needed when installing on N9030B
8121-2090
1Cable, Flex Ribbonb
b.Only needed when installing on N9020B
8121-1683
1 Option BBA Cable Kit (with wire markers) N9030-60018
1 Core Bracket, top N9020-00071
1 Core Bracket, bottom N9020-00072
60 Screws, M3 X 0.5 (8 mm long) 0515-0372
1 Vibration Mount 0460-2725
15 Screws, M3 X 0.5 (6 mm long), flat head 0515-1946
9 Screws, M3 X 0.5 (8 mm long), flat head 0515-2032
2 Screws, Hex Shoulder N9020-20017
2 Main Board Warning Labels N9020-80036
1 Entitlement Certificate 5964-5178
1 Entitlement Certificate Envelope 5967-7169
5 Tie Wrap 1400-0249
1 Installation Note This note
1 Probe tip BNC adapter 5063-2143
1 Cable 8120-2682
6Installation Note N9030-90077
Option BBA, Analog Baseband I/Q Inputs Upgrade Kit
Tools Required
— T-10 Torx Driver
— T-20 Torx Driver
— 5/16-inch torque wrench
— 1/4-inch open end wrench
— 1/4-inch socket on 4 lb torque wrench
—scissorsorknife
—diagonalcutters
— USB storage device with > 2 GB free memory
Keysight Service Center or Customer Calibration Lab:
The following kit items are not installed in the analyzer upgrade and need to be shipped back to the
end user for their use:
— 5063-2143, Probe tip BNC adapter
— 8120-2682, cable
Before you disassemble the instrument, turn the power switch to Standby, wait until the
instrument has completely shut down, and unplug the instrument. Failure to unplug the
instrument can result in personal injury.
Electrostatic discharge (ESD) can damage or destroy electronic components. All work on
electronic assemblies should be performed at a static-safe workstation. Refer to the
documentation that pertains to your instrument for information about static-safe workstations
and ordering static-safe accessories.
Installation Note N9030-90077 7
Option BBA, Analog Baseband I/Q Inputs Upgrade Kit
Installation Procedure
Instrument Cover Removal
1. Power down the instrument and wait for the standby light to come on. Disconnect the
instrument from ac power.
2. Refer to Figure 1. Using the T-20 driver, remove the 4 screws (1) (two on each side) that
attach the strap handles (2) on each side of the instrument.
3. Remove the four key locks from the instrument four bottom feet.
4. Remove the four instrument bottom feet.
5. Using the T-20 driver, remove the four screws (including washers) (3) that hold the rear feet
(4) in place.
6. Pull the instrument cover (5) off towards the rear of the instrument.
If the instrument is placed on its face during any of the following procedures, be sure to use a soft
surface or soft cloth to avoid damage to the front panel, keys, or input connector.
Make sure any adapters on the front panel are removed.
8Installation Note N9030-90077
Option BBA, Analog Baseband I/Q Inputs Upgrade Kit
Figure 1 Instrument Outer Case Removal
Installation Note N9030-90077 9
Option BBA, Analog Baseband I/Q Inputs Upgrade Kit
Front Frame Assembly Removal
1. Refer to Figure 2. Look at the upper right corner of the front panel. If EXT MIXER SMA
connector is present (Option EXM), locate the connection where the two semi-rigid cables
mate behind the front frame (2). Disconnect the connections using a 1/4-inch wrench and a
5/16-inch wrench.
2. Using the T-10 driver, remove and discard the eight screws (1), four on each side, to detach
the front frame from the chassis.
3. Refer to Figure 3. Pull the front frame carefully away from the chassis. Remove the ribbon
cable W1 from the A8 Motherboard.
Figure 2 Front Frame Removal
W1 may have locking springs on each side. Depress the spring on each side of the connector to
remove from the motherboard.
10 Installation Note N9030-90077
Option BBA, Analog Baseband I/Q Inputs Upgrade Kit
Figure 3 Front Panel Cable
Andere Handbücher für N9030B
8
Inhaltsverzeichnis
Andere Keysight Technologies Messgerät Handbücher
Keysight Technologies
Keysight Technologies E5061B Bedienungsanleitung
Keysight Technologies
Keysight Technologies E4990A Bedienungsanleitung
Keysight Technologies
Keysight Technologies EPM Series Bedienungsanleitung
Keysight Technologies
Keysight Technologies N9030B Installations- und Betriebshandbuch
Keysight Technologies
Keysight Technologies B2900A Series Bedienungsanleitung
Keysight Technologies
Keysight Technologies N9010B Installations- und Betriebshandbuch
Keysight Technologies
Keysight Technologies 16034G Bedienungsanleitung
Keysight Technologies
Keysight Technologies N5221/2A Series Bedienungsanleitung
Keysight Technologies
Keysight Technologies N9030B Bedienungsanleitung
Keysight Technologies
Keysight Technologies U5855A Bedienungsanleitung
Keysight Technologies
Keysight Technologies E5260 Series Bedienungsanleitung
Keysight Technologies
Keysight Technologies X Series Betriebsanleitung
Keysight Technologies
Keysight Technologies X-Series Bedienungsanleitung
Keysight Technologies
Keysight Technologies U5310A Benutzerhandbuch
Keysight Technologies
Keysight Technologies U2020 X Series Bedienungsanleitung
Keysight Technologies
Keysight Technologies E2655C Bedienungsanleitung
Keysight Technologies
Keysight Technologies X-Series Kurzanleitung
Keysight Technologies
Keysight Technologies B2980A Series Bedienungsanleitung
Keysight Technologies
Keysight Technologies N9040B Installations- und Betriebshandbuch
Keysight Technologies
Keysight Technologies B1500A Installationsanleitung
