Keysight B2900A Bedienungsanleitung

Keysight Technologies

Using Source/Measure Unit as an Ammeter

B2900A Precision Source/Measure Unit

Demo Guide

02 | Keysight | Using Source/Measure Unit as an Ammeter – Demo Guide

Introduction

The Keysight B2900A Series Precision Source/Measure Unit (SMU) is a compact and

cost-effective bench-top SMU with the capability to output and measure both voltage

and current. The B2900A Series SMU enables you to make a wide range of current

versus voltage (IV) measurements more accurately and quickly than ever before. In

addition, the B2900A Series SMU comes with an intuitive graphical user interface (GUI)

and free PC-based application software that make it easy for you to begin making

productive measurements immediately.

This demonstration guide shows how easily you can use the Keysight B2900A Series

SMU as an ammeter.

Required Instrument and Accessories

All of the accessories required to perform the demos described in this demonstration guide

are provided in a demo kit that is included with Keysight B2902A/12A demo units. The kit

includes items such as a banana cable, a 1.1 kΩ resistor, etc.

Keysight B2902A/12A

Precision Source/Measure Unit

11059A Kelvin Probe Set

1.1 kΩ Resistor

U8201A Combo Test Lead Kit

03 | Keysight | Using Source/Measure Unit as an Ammeter – Demo Guide

Figure 1. Connection diagram and basic condition

Concept

Figure 1 illustrates the connection diagram used in the demo to use the Keysight B2900A

Series SMU as an ammeter. Since the current polarity of the SMU is opposite to an ammeter,

the Low Force terminal of the channel has to be connected to the current output port of the

device under test (DUT).

In this demo, a 1.1 kΩ resistor combined with a power supply is used as a DUT, a current source

circuit. The channel 2 of the B2902A/12A is used as a power supply. However, you can also use

your own power supply for it.

Setup

1. Connect the yellow banana plug of the 11059A to the Ch 1 Low Force Terminal.

2. Connect the red banana plug of the 11059A to the Ch1 High Force Terminal.

3. Clip the end of the 1.1 kΩ resistor with the black gold-plated tweezers of the 11059A.

4. Connect the black banana cable of the U8201A to the Ch2 Low Force Terminal.

5. Connect the red banana cable of the U8201A to the Ch2 High Force Terminal.

6. Clip the other end of the 1.1 kΩ resistor with the red alligator clip of the U8201A

7. Connect the red gold-plated tweezers of the 11059A to the black alligator clip of the U8201A.

A-

Common

High Force

Low Force

DUT

Current

Out

Low

B2901/02/11/12A

1.1 kΩPower

Supply

DUT

Current

Out

Low

Red (11059A)

Yellow (11059A)

Black (11059A)

Red (11059A)

U8201A

Channel 2

as Power Supply

A-

Common

High Force

Low Force

B2901/02/11/12A

1.1 kΩPower

Supply

DUT

Current Out

Low

Channel 1

DUT

1.1 kΩ

04 | Keysight | Using Source/Measure Unit as an Ammeter – Demo Guide

LAB1: Use Source/Measure Unit as an Ammeter

Objective

This demo illustrates the current mea-

surement function as an ammeter by

sourcing 0 V voltage and measuring the

current from the resistor biased by a

power supply using a Source/Measure

Unit.

Procedure

1. Congure the low terminal state to

FLOATING

2. Measure current using the SMU

(Channel 1) as an ammeter

3. Enable the DUT, the current soure

circuit

4. Conrm measured current

5. (Optional) Conguring the

measurement speed

6. (Optional) Conguring the

measurement range operation

Demonstration

In the default setting, the low terminal of the channels in the Keysight B2900A Series SMU is grounded

internally. However, the low terminal can be disconnected from the ground and kept oating. Congur-

ing the low terminal state to FLOATING, which enables you to connect the low terminal to any potential

up to ±250 V, and measuring current with sourcing 0 V from the channel, which makes it possible to

use the channel as an ammeter.

1. Congure the low terminal state to FLOATING

1) If you aren’t on the top of the Function menu, press repeatedly to return to the top level.

Press , , and then press to open the Output Connection

dialogue.

3) Press and select to specify the channel which the Low terminal state is

congured for.

On the top level of the Function menu

In the middle level of the Function menu

Any tree structure can’t be seen

Some tree structure can be seen

(1) Press Config

(2) Press Source

(3) Press Connection

05 | Keysight | Using Source/Measure Unit as an Ammeter – Demo Guide

Press and select , and then press to congure the Low terminal

state to FLOATING.

If the low terminal state of the channel is set to FLOATING, you can see the status

indicator on the GUI as below, although no indicator can be seen on being set to

GROUNDED.

2. Measure current using the SMU (Channel 1) as a ammeter

2-1. Change View mode to Ch1 Single View

1) Press repeatedly until the

Channel 1 Single View is displayed

2-2. Congure the condition to source and measure

1) Press to edit the Source function, and then select to set the Source

function to Voltage source.

GROUNDED FLOATING

06 | Keysight | Using Source/Measure Unit as an Ammeter – Demo Guide

2) Press to edit the Source value, and then enter 0 V to set the Source value to 0 V.

3) Press to edit the Limit value, and then enter 100 mA to set the Limit value to

100 mA for example.

4) Press to congure the Measurement parameter, and then select to set

the Measurement parameter to Current.

5) Rotate and press to edit the Voltage source range operation. Then Select

to set the Voltage source range operation to FIXED.

6) Rotate and press to edit the Voltage source range, and then select to set

it to 200 mV.

07 | Keysight | Using Source/Measure Unit as an Ammeter – Demo Guide

2-3. Perform the measurement

1) Press for the channel 1 to switch on its output terminal.

2) Press to perform a measurement repeatedly. Now you can see the

measurement result on the GUI of the B2902/12A as below.

3. Enable the DUT, the current source circuit

You can also use your own power supply instead of the channel 2 of the B2902A/12A

3-1. Change View mode to Ch2 Single View.

1) Press repeatedly until the

Channel 2 Single View is displayed.

3-2. Congure the condition of the power supply (Channel 2)

1) Press to edit the Source function, and then select to set the Source

function to Voltage source.

2) Press to edit the Source value, and then enter 1.1 V to set the Source

value to 1.1 V for example.

3) Press to edit the Limit value, and then enter 100 mA to set the Limit value

to 100 mA for example.

08 | Keysight | Using Source/Measure Unit as an Ammeter – Demo Guide

4) Press for the channel 2 to switch on its output terminal and enable the DUT.

4. Conrm measured current

4-1. Change View mode to Ch1 Single View.

1) Press repeatedly until

Channel 1 Single View is displayed.

You can see about 1 mA as measured value, since 1 V is sourced to a 1.1 kΩ

resistor. If you press for the channel 2 to switch it off, you can see only the

offset current because the DUT, the current source circuit is disabled.

Theoretically speaking, the measured current should be 1 mA since 1.1 V is sourced

to a 1.1 kΩ resistor. However, it may be varied because the resistor has some error on

its value actually.

Power Supply enabled Power Supply disabled

09 | Keysight | Using Source/Measure Unit as an Ammeter – Demo Guide

5. (Optional) Conguring the measurement speed

In the default setting, the instrument selects the appropriate measurement speed and

range automatically to get the ne accuracy. However, you can also specify these

parameters on the GUI of the B2900A Series SMU to meet a variety of the requirement

to the measurement conditions.

For example, let’s try to change the measurement speed to NORMAL to make a mea-

surement more carefully. If you select NORMAL, the aperture time is set to 1 PLC. Here,

PLC stands for power line cycle and the specied number of power line cycles is used

per a measurement.

1) Press to edit the Measurement speed, and then select to set the

Measurement speed to NORMAL. (If you can’t see in Assist keys, press

to change the keys shown in Assist keys.)

6. (Optional) Conguring the measurement range operation

The parameters which congure the measurement range operation can be displayed in

the Range Sub-panel in the Channel 1 Single View. In the default setting, the B2900A

Series SMU performs the current measurement using a 1 μA current minimum measure-

ment range with AUTO range operation. With AUTO range operation, the B2900A Series

SMU selects the proper range for the measurement with the specied minimum mea-

surement range so that you don’t need to take care about it. To know how to change the

measurement range setting, try to congure to use the 10 μA current minimum mea-

surement range with AUTO range operation.

1) Rotate and press to edit the Current minimum measurement range and then

select to set it to 10 μA.

If you’d like to x the measurement range, you can select FIXED range operation as below.

2) Rotate and press to edit the Current measurement range operation. Then

Select to set the Current measurement range operation to FIXED.

10 | Keysight | Using Source/Measure Unit as an Ammeter – Demo Guide

B2900 Precision Instrument Family

The B2900 family contains products that perform both precision sourcing and

precision measurement. www.keysight.com/nd/b2900a

Conclusion

The Keysight B2900A Series Precision Source/Measure Unit (SMU) is a compact and

cost-effective bench-top SMU with the capability to output and measure both voltage

and current. Although it has the capability to make a wide range of current versus

voltage (IV) measurements as its intrinsic function, the B2900A Series SMU can be used

as an ammeter easily.

Andere Handbücher für B2900A

Andere Keysight Analytisches Instrument Handbücher

Keysight

Keysight N5225-60142 Bedienungsanleitung

Keysight

Keysight N5242-60107 Installations- und Betriebshandbuch

Keysight

Keysight N5241AU-927 Installations- und Betriebshandbuch

Keysight

Keysight DAQ970A Bedienungsanleitung

Keysight

Keysight N5241AU-944 Kurzanleitung

Keysight

Keysight N5247-60106 Installations- und Betriebshandbuch

Keysight

Keysight N5242-60115 Installations- und Betriebshandbuch

Keysight

Keysight N5221AU-626 Installations- und Betriebshandbuch

Keysight

Keysight N5224B PNA Kurzanleitung

Keysight

Keysight 41901A SMD Bedienungsanleitung

Keysight

Keysight N9912A Bedienungsanleitung

Keysight

Keysight E8740A-020 Benutzerhandbuch

Keysight

Keysight N5241BU-622 Installations- und Betriebshandbuch

Keysight

Keysight PD1500A Betriebsanleitung

Keysight

Keysight N5224A Bedienungsanleitung

Keysight

Keysight N5245-60121 Installations- und Betriebshandbuch

Keysight

Keysight x series Installations- und Betriebshandbuch

Keysight

Keysight B Series Bedienungsanleitung

Keysight

Keysight N5245-60117 Bedienungsanleitung

Keysight

Keysight N5222-60133 Installations- und Betriebshandbuch

Keysight

Keysight N5247-60103 Installations- und Betriebshandbuch

Keysight

Keysight 16440A Bedienungsanleitung

Keysight

Keysight U7233A Bedienungsanleitung

Beliebte Analytisches Instrument Handbücher anderer Marken

Cocraft

Cocraft NLT04 Bedienungsanleitung

M&C

M&C GENTWO PMA1000 Bedienungsanleitung

MICRO-EPSILON

MICRO-EPSILON optoncdt 1700 Bedienungsanleitung

CONDTROL

CONDTROL XP4 PRO Bedienungsanleitung

Extech Instruments

Extech Instruments BR200 Bedienungsanleitung

Dewetron

Dewetron DEWE-30-16 Produkthandbuch

EXTOL PREMIUM

EXTOL PREMIUM 8820043 Montage- und Bedienungsanleitung

RIDGID

RIDGID SeeSnake Compact Bedienungsanleitung

Teledyne

Teledyne 3000PA Bedienungsanleitung

YDLIDAR

YDLIDAR TIA Bedienungsanleitung

Olympus

Olympus IPLEX FX Series Bedienungsanleitung

Bosch

Bosch GLM 50 C Professional Bedienungsanleitung

Reflecta

Reflecta DigiEndoscope Bedienungsanleitung

Chinavision

Chinavision CVACZ-G696 Montageanleitung

Fuji Electric

Fuji Electric ZKMA Bedienungsanleitung

Teledyne

Teledyne 3300TA Bedienungsanleitung

VOLTCRAFT

VOLTCRAFT IC-100HD Bedienungsanleitung

RIDGID

RIDGID micro CA-25 Bedienungsanleitung