Keysight E8362-60109 Installations- und Betriebshandbuch

Agilent Part Number: E8362-90004

Printed in USA May 2003

Installation Note

Extended Frequency Range Upgrade Kit

For E8362B PNA Series Microwave Network Analyzers WITHOUT the

Configurable Test Set Option

Network Analyzer

Model Number

Upgrade Kit

Part Number

Frequency

Extension

E8362B E8362-60109 20 GHz to 40 GHz

2Installation Note E8362-90004

Notice

THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT

TO BEING CHANGED, WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE

MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, AGILENT DISCLAIMS ALL

WARRANTIES, EITHER EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY

INFORMATION CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

AGILENT SHALL NOT BE LIABLE FOR ERRORS OR FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING, USE, OR

PERFORMANCE OF THIS DOCUMENT OR ANY INFORMATION CONTAINED HEREIN.

SHOULD AGILENT AND THE USER HAVE A SEPARATE WRITTEN AGREEMENT WITH

WARRANTY TERMS COVERING THE MATERIAL IN THIS DOCUMENT THAT CONFLICT

WITH THESE TERMS, THE WARRANTY TERMS IN THE SEPARATE AGREEMENT WILL

CONTROL.

Getting Assistance from Agilent

By internet, phone, or fax, get assistance with all your test and measurement needs.

Online assistance: www.agilent.com/find/assist

United States

(tel) 1 800 452 4844

Latin America

(tel) (305) 269 7500

(fax) (305) 269 7599

Canada

(tel) 1 877 894 4414

(fax) (905) 282-6495

Europe

(tel) (+31) 20 547 2323

(fax) (+31) 20 547 2390

Australia

(tel) 1 800 629 485

(fax) (+61) 3 9210 5947

New Zealand

(tel) 0 800 738 378

(fax) (+64) 4 495 8950

Japan

(tel) (+81) 426 56 7832

(fax) (+81) 426 56 7840

Singapore

(tel) 1 800 375 8100

(fax) (65) 836 0252

Malaysia

(tel) 1 800 828 848

(fax) 1 800 801 664

India

(tel) 1 600 11 2929

(fax) 000 800 650 1101

Hong Kong

(tel) 800 930 871

(fax) (852) 2506 9233

Taiwan

(tel) 0800 047 866

(fax) (886) 2 25456723

Philippines

(tel) (632) 8426802

(tel) (PLDT subscriber only)

1 800 16510170

(fax) (632) 8426809

(fax) (PLDT subscriber only)

1 800 16510288

Thailand

(tel) (outside Bangkok)

(088) 226 008

(tel) (within Bangkok)

(662) 661 3999

(fax) (66) 1 661 3714

People’s Republic of China

(tel) (preferred)

800 810 0189

(tel) (alternate)

10800 650 0021

(fax) 10800 650 0121

Installation Note E8362-90004 3

About the Upgrade Kit

If you need assistance, refer to “Getting Assistance from Agilent” on page 2.

Description of the Upgrade

This upgrade kit is used to extend the frequency range of the:

• E8362B PNA microwave network analyzer from 20 GHz to 40 GHz

Products affected. . . . . . . . . . . . . . . . . . . . . . . . . . E8362B without Option 014, Configurable

Test Set

Installation to be performed by . . . . . . . . . . . . . . Agilent service center or personnel

qualified by Agilent

Estimated installation time . . . . . . . . . . . . . . . . . 1 hour

Estimated verification time . . . . . . . . . . . . . . . . . 5 minutes

Estimated calibration adjustment time. . . . . . . . 45 minutes

4Installation Note E8362-90004

Items Included in the Upgrade Kit

Check the contents of your kit against the following list. If any item is missing or damaged,

contact Agilent Technologies. Refer to “Getting Assistance from Agilent” on page 2.

Table 1 Option 040 Upgrade Kit (E8362-60109) to Extend the E8362B to 40 GHz

Ref.

Desig. Description Qty Part Number

Parts for all analyzer options (except Option 014)

N/A Installation note (this document) 1 E8362-90004

N/A License key certificate 1 5964-5136

N/A Model number nameplate (for 40 GHz analyzer, E8363B) 1 E8363-80002

A21 SOMA 50 1 5087-7130

A23 Channel R1 detector

2 5087-7133

A24 Channel R2 detector

A25 Test port 1 coupler

2 5087-7518

A26 Test port 2 coupler

A27 Channel A first converter (mixer)

2 5087-7122

A30 Channel B first converter (mixer)

N/A Machine screw M3.0 x 18 (for attaching A23 and A24 detectors) 4 0515-0666

N/A Machine screw M3.0 x 30 (for attaching SOMA 50) 4 0515-1349

N/A Ribbon cable, A21 SOMA 50 to A16 test set motherboard 1 8121-0818

N/A Cable, wrapped wire, detectors to A16 test set motherboard 2 E7340-60075

N/A Test set deck front panel 1 E8364-00014

W1 A12 source 20 to A21 SOMA 50 1 E8364-20036

W2 A21 SOMA 50 to A22 switch/splitter 1 E8364-20034

W3 A22 switch/splitter to A23 channel R1 detector 1 E8364-20144

W4 A22 switch/splitter to A24 channel R2 detector 1 E8364-20024

W37 A23 channel R1 detector to A16 test set motherboard J204 1 E8364-60121

W38 A24 channel R2 detector to A16 test set motherboard J205 1 E8364-60122

W39 A21 SOMA 50 to A16 test set motherboard J206 1 E8364-60123

Installation Note E8362-90004 5

Parts for analyzers WITH NO RF hardware options

W7 A23 channel R1 detector to A28 channel R1 mixer 1 E8364-20025

W8 A24 channel R2 detector to A29 channel R2 mixer 1 E8364-20026

Parts for analyzers WITH Option UNL ONLY

W7 A23 channel R1 detector to A28 channel R1 mixer 1 E8364-20174

W8 A24 channel R2 detector to A29 channel R2 mixer 1 E8364-20175

Parts for analyzers WITH Options UNL and 016 ONLY

W7 A23 channel R1 detector to A28 channel R1 mixer 1 E8364-20149

W8 A24 channel R2 detector to A29 channel R2 mixer 1 E8364-20150

Table 1 Option 040 Upgrade Kit (E8362-60109) to Extend the E8362B to 40 GHz

Ref.

Desig. Description Qty Part Number

6Installation Note E8362-90004

Installation Procedure for the Upgrade Kit

The network analyzer must be in proper working condition prior to installing this option. Any

necessary repairs must be made before proceeding with this installation.

WARNING

This installation requires the removal of the analyzer’s protective outer

covers. The analyzer must be powered down and disconnected from the

mains supply before performing this procedure.

Electrostatic Discharge Protection

Protection against electrostatic discharge (ESD) is essential while removing or connecting

cables or assemblies within the network analyzer.

Static electricity can build up on your body and can easily damage sensitive internal circuit

elements when discharged. Static discharges too small to be felt can cause permanent

damage. To prevent damage to the instrument:

•always wear a grounded wrist strap having a 1 MΩresistor in series with it when handling

components and assemblies.

•always use a grounded, conductive table mat while working on the instrument.

•always wear a heel strap when working in an area with a conductive floor. If you are

uncertain about the conductivity of your floor, wear a heel strap.

Figure 1 shows a typical ESD protection setup using a grounded mat and wrist strap. Refer to

“Tools Required for the Installation” on page 7 for part numbers.

Figure 1 ESD Protection Setup

Installation Note E8362-90004 7

Overview of the Installation Procedure

Step 1. Verify the Model, Serial, and Option Numbers of the Analyzer

Step 2. Remove the Outer Cover

Step 3. Remove the Inner Cover

Step 4. Remove the Front Panel Assembly

Step 5. Disconnect the A12 Source 20 to A22 Switch/Splitter Cable at the A12 Source 20

Step 6. Raise the Receiver Deck

Step 7. Remove the Old Hardware and Cables

Step 8. Replace the A38 and A39 Bias Tees (Option UNL Only)

Step 9. Install the Remaining New Hardware

Step 10. Install the Remaining Cables

Step 11. Lower the Receiver Deck

Step 12. Connect the A12 Source 20 to A21 SOMA 50 Cable at the A12 Source 20

Step 13. Replace the Front Panel Nameplate

Step 14. Reinstall the Front Panel Assembly

Step 15. Reinstall the Inner and Outer Covers

Step 16. Enter the New Model Number

Step 17. Verify that the New Model Number Is Shown Correctly

Step 18. Perform Source and Receiver Calibration Adjustments

Tools Required for the Installation

ESD Equipment and Supplies Required for the Installation

Description Agilent Part Number

T-8 TORX driver (set to 5 in-lbs) N/A

T-10 TORX driver (set to 9 in-lbs) N/A

T-20 TORX driver (set to 21 in-lbs) N/A

5/16-inch torque wrench (set to 10 in-lbs) N/A

1-inch torque wrench (set to 72 in-lbs) N/A

Description Agilent Part Number

ESD grounding wrist strap 9300-1367

5-ft grounding cord for wrist strap 9300-0980

2 x 4 ft conductive table mat and 15-ft grounding wire 9300-0797

ESD heel strap (for use with conductive floors) 9300-1308

8Installation Note E8362-90004

Equipment Required for Post-Installation Adjustments

Step 1. Verify the Model, Serial, and Option Numbers of the Analyzer

Refer to the License Key Certificate supplied with the kit:

• Verify that the analyzer’s model and serial numbers match those on the certificate.

• Verify that the option number on the certificate matches the option described by this

installation note.

If the model, serial, or option number do not match the expected results, you will not be able

to install the option. If this is the case, contact Agilent for assistance. Refer to “Getting

Assistance from Agilent” on page 2.

Equipment Type Model or

Part Number

Alternate Model or

Part Number

Power meter E4418B/E4419B E4418A/E4419A

Power sensor, 2.4 mm 8487A None

Adapter, 2.4 mm (f) to 2.4 mm (f) 11900B 85056-60007

RF cable, 2.4 mm (f) to 2.4 mm (f) 85133C 85133E

Installation Note E8362-90004 9

Step 2. Remove the Outer Cover

CAUTION

This procedure is best performed with the analyzer resting on its front

handles in the vertical position. Do not place the analyzer on its front panel

without the handles. This will damage the front panel assemblies.

1. Disconnect the power cord (if it has not already been disconnected).

2. Using a T-20 TORX driver, remove the strap handles (item ①) by loosening the screws

(item ②) on both ends until the handle is free of the analyzer.

3. Using a T-20 TORX driver, remove the four rear panel feet (item ③) by removing the center

screws (item ④).

4. Slide the four bottom feet (item ⑤) off the cover.

5. Slide the cover off of the frame.

Figure 2 Outer Cover Removal

10 Installation Note E8362-90004

Step 3. Remove the Inner Cover

1. Place the analyzer top-side up on a flat surface.

2. Using a T-10 TORX driver, remove the eleven screws (item ①).

3. Lift off the cover.

Figure 3 Inner Cover Removal

Inhaltsverzeichnis

Andere Keysight Messgerät Handbücher

Keysight

Keysight SR101EDUA Bedienungsanleitung

Keysight

Keysight M9601A Bedienerhandbuch

Keysight

Keysight N9030A Installations- und Betriebshandbuch

Keysight

Keysight E4980A Bedienungsanleitung

Keysight

Keysight N5241BU-229 Bedienungsanleitung

Keysight

Keysight E5505A Bedienungsanleitung

Keysight

Keysight x series Bedienungsanleitung

Keysight

Keysight N5227BU-420 Bedienungsanleitung

Keysight

Keysight 11590B Service-Handbuch

Keysight

Keysight M9703A Series Benutzerhandbuch

Keysight

Keysight 537A Kurzanleitung

Keysight

Keysight N9040B Option 513 Bedienungsanleitung

Keysight

Keysight 42941A Bedienungsanleitung

Keysight

Keysight M9383B VXG-m Bedienungsanleitung

Keysight

Keysight N1911A Betriebsanleitung

Keysight

Keysight N9342CN Bedienungsanleitung

Keysight

Keysight 16192A Bedienungsanleitung

Keysight

Keysight PNA E8362C Bedienungsanleitung

Keysight

Keysight M9485A Bedienungsanleitung

Keysight

Keysight E4982A Bedienungsanleitung

Keysight

Keysight M9392A Benutzerhandbuch

Keysight

Keysight N5222-60119 Installations- und Betriebshandbuch

Keysight

Keysight PD1000A Bedienungsanleitung

Keysight

Keysight x-series Betriebsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung