Keysight N9030A Installations- und Betriebshandbuch

Notice: This document contains references to Agilent.

Please note that Agilent’s Test and Measurement busi-

ness has become Keysight Technologies. For more in-

formation, go to www.keysight.com.

Keysight N9030A Signal Analyzer

Option BBA

Analog Baseband IQ Inputs

Retrofit Kit

Installation Note

Part Number N9030-90045

Printed in USA August 2014

Notice.

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but not

limited to, the implied warranties of merchantability and fitness for a particular purpose. Keysight

Technologies shall not be liable for errors contained herein or for incidental orconsequential damages

inconnection with the furnishing, performance, or use of this material.

Installation Note N9030-90045 3

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Products Affected: N9030A, PXA Signal Analyzer with Options 503,

508, 513, or 526

Serial Numbers: All

Option BBA

To Be Performed By: (X) Agilent Service Center

(X) Personnel Qualified by Agilent

( ) Customer

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Timea:

a. To ensure that this newly installed option is functioning properly, the procedure that follows includes

the requirement of performing certain adjustments and performance verification tests. However, the

completion of these tests does not guarantee that the instrument meets all advertised specifications.

Software and test equipment is required for making adjustments and for performance verification testing.

Information on how to obtain this software can be found at:

www.agilent.com/find/calibrationsoftware

While Agilent does recommend that a full calibration be performed after the installation of this upgrade,

the end user must ultimately determine whether they want this service or not. If a full calibration is

required, arrangements regarding the level of calibration must be made between the end user and the

calibration provider.

3.0 Hours

0.5 Hours

3.0 Hours

4Installation Note N9030-90045

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Introduction

This kit provides all parts and instructions necessary to install Option BBA, Analog Baseband I/Q

Input, into the Agilent N9030A with frequency range 26.5 GHz and below.

NOTE

1. The signal analyzer requires software revision A.08.54 or newer.

This retrofit kit installation requires that you re-install instrument software even if the current

software meets the revision requirement above.

The latest revision of the PXA Signal Analyzer software may be downloaded from

http:/www.agilent.com/find/xseries_software.

The instrument software must be installed AFTER the hardware in the kit is installed. Follow the

procedure in this document for redeeming and installing the option upgrade license key.

2. The option is licensed for one instrument model/serial number combination. The license key will

only install on the designated instrument.

Installation Note N9030-90045 5

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Installation Kit Parts List

Quantity Description Agilent Part Number

1 BBIQ Main Board N9020-65093

1 LED Board N9020-63095

1 BBIQ Interface Board N9020-65094

1 LED Board Overlay, Bottom N9020-80013

1 LED Board Overlay, Top N9020-80014

1 Cable, Flex Ribbon 8121-2090

1 Core Bracket N9020-00012

1 Cable, Small Coaxial 8121-1401

1 Cable, RF Switch 1 - Switch 2 N9020-20210

1 Display Bracket W1312-00115

60 Screws, M3 X 0.5 (8 mm long) 0515-0372

1 Vibration Mount 0460-2725

9 Screws, M3 X 0.5 (6 mm long) 0515-1227

9 Screws, M3 X 0.5 (8 mm long) 0515-1035

2 Screws, Hex Shoulder N9020-20017

2 Main Board Warning Labels N9020-80036

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate Envelope 5967-7169

2 #1 Cable Label 7121-5601

2 #7 Cable Label 7121-5607

2 #0 Cable Label 7121-5610

5 Tie Wrap 1400-0249

1 Installation Note This note

1 Probe tip BNC adapter (send to end user) 5063-2143

1 Cable, BNC - BNC (send to end user) 8120-2682

6Installation Note N9030-90045

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Tools Required

❏PXA Service Guide as N9030A-0BW or N9030-90030

❏T-10 Torx Driver

❏T-20 Torx Driver

❏5/16-inch torque wrench

❏1/4-inch open end wrench

❏1/4-inch socket on 4 lb torque wrench

❏scissors or knife

❏diagonal cutters

❏USB storage device with > 2 GB free memory

WARNING Before you disassemble the instrument, turn the power switch to Standby,

wait until the instrument has completely shut down, and unplug the

instrument. Failure to unplug the instrument can result in personal injury.

CAUTION Electrostatic discharge (ESD) can damage or destroy electronic components. All

work on electronic assemblies should be performed at a static-safe workstation.

Refer to the documentation that pertains to your instrument for information about

static-safe workstations and ordering static-safe accessories.

Agilent Service Center or Customer Calibration Lab:

The following kit items are not installed in the analyzer upgrade and need to be shipped back to the

end user for their use:

• USB storage device

• 5063-2143, Probe tip BNC adapter

• 8120-2682, cable

• Entitlement Certificate

Installation Note N9030-90045 7

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Installation Procedure

CAUTION If the instrument is placed on its face during any of the following procedures, be

sure to use a soft surface or soft cloth to avoid damage to the front panel, keys, or

input connector.

NOTE Make sure any adapters on the front panel are removed.

Licensing the Option

Installation Procedure using USB Storage Device

1. Locate the Option Upgrade Entitlement Certificate from the kit.

2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the

Certificate.

3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an

attached License File.

4. Locate a USB storage device. Perform a virus scan on this device before use.

5. Save the License File to the root directory of the USB Storage Device.

6. Assure the instrument is fully booted.

7. Connect the USB Storage Device to one of the USB ports. Windows will detect the new hardware

and may display the configuration menu shown in Figure 1. This menu may be configured

according to your preferences.

Figure 1 USB Storage Device Configuration Menu

8Installation Note N9030-90045

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

8. The instrument will automatically consume the License File (this may take a few minutes). When

the License File is consumed the Agilent License Manager will display a “Successful

License Installation” message as shown in Figure 2.

Figure 2 Successful License Installation

Alternate Installation Procedure

The License File can be manually installed over USB or LAN by placing the license file in the

following folder on the MXA C:\Program Files\Agilent\licensing.

Installation Note N9030-90045 9

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Instrument Cover Removal

1. Power down the instrument and wait for the standby light to come on. Disconnect the instrument

from ac power.

2. Refer to Figure 3. Using the T-20 driver, remove the 4 screws (1) (two on each side) that attach

the strap handles (2) on each side of the instrument.

3. Remove the four key locks from the instrument four bottom feet.

4. Remove the four instrument bottom feet.

5. Using the T-20 driver, remove the four screws (including washers) (3) that hold the rear feet (4)

in place.

6. Pull the instrument cover (5) off towards the rear of the instrument.

Figure 3 Instrument Outer Case Removal

10 Installation Note N9030-90045

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Front Frame Assembly Removal

1. Refer to Figure 4. Look at the upper right corner of the front panel. If EXT MIXER SMA

connector is present (Option EXM), locate the connection where the two semi-rigid cables mate

behind the front frame (2). Disconnect the connections using a 1/4-inch wrench and a 5/16-inch

wrench.

2. Using the T-10 driver, remove the eight screws (1), four on each side, to detach the front frame

from the chassis.

3. Refer to Figure 5. Pull the front frame carefully away from the chassis. Remove the ribbon cable

W1 from the A8 Motherboard.

NOTE W1 may have locking springs on each side. Depress the spring on each side of the

connector to remove from the motherboard.

Figure 4 Front Frame Removal

Andere Handbücher für N9030A

Inhaltsverzeichnis

Andere Keysight Messgerät Handbücher

Keysight

Keysight E5080A Bedienungsanleitung

Keysight

Keysight U1832A Bedienungsanleitung

Keysight

Keysight x series Betriebsanleitung

Keysight

Keysight ENA Series Bedienungsanleitung

Keysight

Keysight N5224AU-217 Installations- und Betriebshandbuch

Keysight

Keysight N7744A Bedienungsanleitung

Keysight

Keysight Streamline Series Benutzerhandbuch

Keysight

Keysight 775D Service-Handbuch

Keysight

Keysight MXA 902 Series Installations- und Betriebshandbuch

Keysight

Keysight M9602A PXIe Benutzerhandbuch

Keysight

Keysight U1190A Series Bedienungsanleitung

Keysight

Keysight 34420A Bedienungsanleitung

Keysight

Keysight M31 A Series Bedienungsanleitung

Keysight

Keysight N2790A Bedienungsanleitung

Keysight

Keysight x series Bedienungsanleitung

Keysight

Keysight M9005A Bedienungsanleitung

Keysight

Keysight M9392A Benutzerhandbuch

Keysight

Keysight N2795/6A Bedienungsanleitung

Keysight

Keysight PNA-X N5241A Installations- und Betriebshandbuch

Keysight

Keysight N9913A Bedienungsanleitung

Keysight

Keysight U1731C Bedienungsanleitung

Keysight

Keysight x series Installations- und Betriebshandbuch

Keysight

Keysight U1211A Bedienungsanleitung

Keysight

Keysight x-series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung