Keysight N2140A Bedienungsanleitung

Quick Start Guide

*N2140-92000*

N2140-92000, July 2016,

Printed in USA

If your probe requires cleaning, disconnect

it from the instrument and clean it with

mild detergent and water. Make sure the

probe is completely dry before connecting

it to the instrument.

Safety and Regulatory Information

The CE mark is a registered trademark of the

European Community. ISM GRP 1-A denotes the

instrument is an Industrial Scientific and Medical

Group 1 Class A product. ICES/NMB-001

indicates product compliance with the Canadian

Interference-Causing Equipment Standard.

IEC Measurement category II is for measurements

performed on circuits directly connected to the

low voltage installation. Example. Household

appliances portable tools, and similar equipment.

CSA is the Canadian certification mark to

demonstrate compliance with the Safety requirements.

CAT II

Indoor Use Only. Do not operate in wet / damp

environments. Keep product surfaces dry and

clean.

Do not operate in an explosive environment.

The probe cable is a sensitive part of the probe

and, therefore, you should be careful not to

damage it through excessive bending or pulling.

Avoid any mechanical shocks to the product to

guarantee accurate performance and protection.

Some of the probe tips / accessories are very

sharp. You should handle these with care to

avoid personal injury.

Use only Grounded instruments. Do not connect

the probe’s ground lead to a potential other than

earth ground. Always make sure that the probe

and oscilloscope are grounded properly.

Connect the probe to the oscilloscope and

connect the ground lead to earth ground before

connecting the probe to the circuit under test.

Disconnect the probe input and the probe ground

lead from the circuit under test before

disconnecting the probe from the oscilloscope.

Do not use the probe assembly if the red wear

indicator in the cable has become visible.

Keysight N2140A and N2142A

Passive Probes

This symbol indicates the Environmental Protection

Use Period (EPUP) for the product’s toxic

substances for the China RoHS requirements.

The Keysight N2140A 200 MHz and N2142A 75 MHz passive

probes are high impedance probes with switchable attenuation

ratio (1:1 and 10:1). These are compatible with the Keysight

InfiniiVision EDUX1002A/G and DSOX1102A/G digital storage

oscilloscopes or similar oscilloscopes with 1 Mohm BNC input.

Table 3 - Physical & Environmental Characteristics

Characteristic Value

Probe Body

Cable Length

Weight

95mm

1200mm

55g

Table 2 - Electrical Characteristics

Characteristic Value

Attenuation Ratio

Input Capacitance

Compensation range

(when terminated

into 1 Mohm)

1:1 / 10:1

1:1 - 100pf

15pf - 40pf

Input Resistance

Maximum Input

Voltage

1:1 - 150V rms CAT II

1:1 - 1MΩ

Temperature

Humidity

Altitude

The BNC connector of these probes has a

pin hole without a pin. This is as per the

design and does not indicate any damage

or fault in the probe.

These probes have been designed and calibrated for use

with instruments having an input impedance of 1M Ω

paralleled by 20pF. However, these may be recalibrated for

use with instruments having an input capacitance of

15 to 40pF.

Adjusting Probes for Low-Frequency (LF) Compensation

The probe should be adjusted for LF compensation when it is

connected to an oscilloscope input for the first time. LF

compensation matches the probe cable capacitance to the

oscilloscope input capacitance. This matching assures good

amplitude accuracy from DC to the upper bandwidth limit

frequencies. A poorly compensated probe clearly influences

the overall system performance (probe and oscilloscope)

and introduces measurement errors resulting in inaccurate

readings and distorted waveforms.

To perform LF compensation:

1 Connect the probe to the oscilloscope’s front-panel

calibration output (a square wave label is usually seen near

this output).

2 Use the supplied adjustment tool to adjust the LF

compensation to an optimum square wave response as

shown in the figure below.

10:1 - 15pf

10:1 - 10MΩ

Table 1 - Probe and its Supplied Accessories

ID Part Quantity

For N2140A For N2142A

Hook Tip

Ground Spring

Ground Lead

Adjustment Tool

Protective Cap

Channel

Identification rings

1 1

2 sets of each color with

two rings in each set

These accessories are provided in the N2141A kit for the

N2140A probe and the N2143A kit for the N2142A probe.













Undercompensated Overcompensated Optimum

10:1 - 300V rms CAT II

3,000 m (9,842 ft) (Operating)

12200 m (40,026 ft) (Non-operating)

Bandwidth For N2140A

1:1 - 6 MHz

10:1 - 200 MHz

For N2142A

1:1 - 6 MHz

10:1 - 75 MHz

5% to 95% RH up to 30 °C (Operating)

5% to 65% RH above 30 °C up to 55 °C

-10 °C to +55 °C (Operating)

-40 °C to +70 °C (Non-operating)



Passive probe

2 2

BNC

Connector

Pin hole

without

apin Current Rating

(DC, 1:1, & maximum voltage)

0.15mA

Dieses Handbuch passt für folgende Modelle

Andere Keysight Messgerät Handbücher

Keysight

Keysight x series Bedienungsanleitung

Keysight

Keysight N9010AK-MTU Installations- und Betriebshandbuch

Keysight

Keysight N432A Bedienungsanleitung

Keysight

Keysight N1914A Bedienungsanleitung

Keysight

Keysight x series Bedienungsanleitung

Keysight

Keysight N9342CN Bedienungsanleitung

Keysight

Keysight N4372E Bedienungsanleitung

Keysight

Keysight M9602A PXIe Benutzerhandbuch

Keysight

Keysight 9020A Installations- und Betriebshandbuch

Keysight

Keysight x-series Produktinformationsblatt

Keysight

Keysight M9217A PXIe 2-CH Benutzerhandbuch

Keysight

Keysight N2862B Bedienungsanleitung

Keysight

Keysight U8903A Bedienungsanleitung

Keysight

Keysight FieldFox A Series Bedienungsanleitung

Keysight

Keysight MXA 902 Series Installations- und Betriebshandbuch

Keysight

Keysight 8990B Bedienungsanleitung

Keysight

Keysight U2781A Bedienungsanleitung

Keysight

Keysight PNA Series Montage- und Wartungsanleitung

Keysight

Keysight A Series Bedienungsanleitung

Keysight

Keysight 4284A Installationsanleitung

Keysight

Keysight N5241BU-229 Bedienungsanleitung

Keysight

Keysight E4981A Betriebsanleitung

Keysight

Keysight 775D Service-Handbuch

Keysight

Keysight N1911A Betriebsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

ADTEK

ADTEK MW-5 Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung