Keysight PXA X Series Installations- und Betriebshandbuch

Notice: This document contains references to Agilent.

Please note that Agilent’s Test and Measurement busi-

ness has become Keysight Technologies. For more in-

formation, go to www.keysight.com.

Keysight PXA Signal Analyzer

Option CR3 Second IF Out

Option CRP Arbitrary IF Out

Option ALV Log Video Out

Installation Note

Part Number N9030-90036

Printed in USA August 2014

Notice.

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but not

limited to, the implied warranties of merchantability and fitness for a particular purpose. Keysight

Technologies shall not be liable for errors contained herein or for incidental orconsequential damages

inconnection with the furnishing, performance, or use of this material.

Installation Note N9030-90036 3

Option CR3, or CRP, or ALV Installation Kit

Products Affected: PXA N9030A

Serial Numbers: All

Options

To Be Performed By: (X) Agilent Service Center

(X) Personnel Qualified by Agilent

(X) Customer

Estimated Installation Time:

Estimated Adjustment and Verification Time: 0.5 Hours

0.5 Hours

4Installation Note N9030-90036

Option CR3, or CRP, or ALV Installation Kit

Introduction

This kit contains all of the instructions required to install Option CR3, CRP, or ALV on an Agilent

PXA X-Series signal analyzer.

The rear panel AUX IF OUT port is present on all PXA signal analyzer, however each of the possible

output signal choices require a license.

NOTE

1. At the time of manufacture the hardware related to this option was fully adjusted and the option

performance was verified to be within its warranted specifications. Within one year of the initial

calibration date of the instrument this option is fully calibrated with no further adjustment or

verification testing.

To determine the initial calibration date, locate the original calibration certificate that was shipped

with the instrument at the time of purchase. The Date of Calibration is printed on the original

calibration certificate.

To ensure that this newly installed option has been installed properly, the procedure that follows

includes a functional check.

2. The latest revision of the X-Series signal analyzer software may be downloaded from:

http://www.agilent.com/find/Xseries_software

3. This option is licensed for one instrument model/serial number combination. The license key will

only install on the designated instrument.

Contents

Quantity Description Agilent Part

Number

1 Installation Note This note

1 Option Upgrade Entitlement Certificate 5964-5178

Installation Note N9030-90036 5

Option CR3, or CRP, or ALV Installation Kit

Tools Required for Installation

❏Personal computer with internet access and USB port

❏USB storage device with > 2 GB free memory

Tools Required for Manual Operation Verification

For Option CR3 and CRP

❏Spectrum Analyzer capable of measuring a 322.5 MHz signal at -40 dBm

❏Test cable, sma or 3.5 mm connectors

❏Adapters as needed to connect the cable between the spectrum analyzer and sma AUX IF OUT

port on the rear panel of the N9030A

For Option ALV

❏Signal source capable of providing pulse output above 200 MHz

❏Oscilloscope

❏Test cable, BNC

❏BNC (f) to sma (m) adapter to connect the cable between the oscilloscope and sma AUX IF OUT

port on the rear panel of the spectrum analyzer

6Installation Note N9030-90036

Option CR3, or CRP, or ALV Installation Kit

Installation Procedure over USB

1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.

2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the

Certificate.

3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an

attached License File.

4. Locate a USB storage device. Perform a virus scan on this device before use.

5. Save the License File to the root directory of the USB Storage Device.

6. Connect the USB Storage Device to the signal analyzer USB port. Windows will detect the new

hardware and may display the configuration menu shown in Figure 1. This menu may be

configured according to your preferences.

Figure 1 USB Storage Device Configuration Menu

7. The signal analyzer will automatically consume the License File. (This may take a few minutes)

When the License File is consumed the Agilent License Manager will display a “Successful

License Installation” message as shown in Figure 2.

Figure 2 Successful License Installation

Installation Note N9030-90036 7

Option CR3, or CRP, or ALV Installation Kit

Alternate Installation Procedure

The License File can be manually installed over USB or LAN by placing the license file in the

following folder on the signal analyzer

C:\Program Files\Agilent\licensing

Verify the Installation

1. Cycle the power on the signal analyzer.

2. Press System, Show, System to display a list of installed options.

3. Verify that the newly installed option appears on the list.

Functional Check:

Within one year of the initial calibration date of the instrument this option is fully calibrated with no

further adjustment or verification testing. To ensure that this newly installed option has been enabled

correctly the following functional check is recommended.

1. Press System, Show, Errors, Clear Error Queue. This will remove out-of-date errors.

2. Press System, Alignments, Align Now, All.

3. Watch for any errors during the instrument alignment.

4. Press System, Show, Errors to view the instrument error log.

5. Verify that there were no errors during the alignment.

8Installation Note N9030-90036

Option CR3, or CRP, or ALV Installation Kit

Manually verify operation

Option CR3, Second IF Output

1. Preset X-Series analyzer. Assure mode is Spectrum Analyzer.

2. Display the 50 MHz calibrator signal. Press Input/Output, RF Calibrator, 50 MHz. Press

FREQ/Channel, key in 50 MHz. Press Span, Zero Span. You should see a flat line across the

display at -25 dBm.

3. Enable Option CR3. Press Input/Output, More, Output Configuration, Aux IF Out, Second IF

Out.

4. Connect a spectrum analyzer to the rear panel Aux IF Out port using test cable and appropriate

adapters.

Spectrum analyzer settings:

Center frequency: 322.5 MHz

Span: 1 MHz

Bandwidth: 100 kHz

The spectrum analyzer should display a −33 dBm ±5 dB signal

Option CRP, Arbitrary IF Output

1. Preset X-Series analyzer. Assure mode is Spectrum Analyzer.

2. Display the 50 MHz calibrator signal. Press Input/Output, RF Calibrator, 50 MHz. Press

FREQ/Channel, key in 50 MHz. Press Span, Zero Span. You should see a flat line across the

display at -25 dBm.

3. Enable Option CRP. Press Input/Output, More, Output Configuration, Aux IF Out, Arbitrary IF.

Set the Arbitrary IF Out frequency to 70 MHz using the key pad.

4. Connect a spectrum analyzer to the rear panel Aux IF Out port using test cable and appropriate

adapters.

Spectrum analyzer settings:

Center frequency: 70 MHz

Span: 1 MHz

Bandwidth: 100 kHz

The spectrum analyzer should display a −33 dBm ±5 dB signal

Installation Note N9030-90036 9

Option CR3, or CRP, or ALV Installation Kit

Option ALV, Fast Log Video

1. Preset X-Series analyzer. Assure mode is Spectrum Analyzer.

2. Enable Option ALV. Press Input/Output, More, Output Configuration, Aux IF Out, Fast Log

Video.

3. Connect a signal source configured for a pulse output to the X-Series analyzer RF input port. The

frequency of the pulse should be above 200 MHz. Example settings are:

Pulse frequency: 400 MHz

Amplitude: −20 dBm

Pulse period: 80 μsec

Pulse width: 40 μsec

4. Spectrum analyzer settings:

Center frequency: 400 MHz

Span: 0 Hz

Bandwidth: 3 MHz

5. Connect an oscilloscope to the spectrum analyzer rear panel Aux IF Out port.

Oscilloscope settings:

500 mV/div

10 μsec/div

Adjust oscilloscope to view the pulse on the oscilloscope. Pulse should measure approximately

1.3 VP-P

10 Installation Note N9030-90036

Option CR3, or CRP, or ALV Installation Kit

Utilities, Adjustments, and Performance Verification Tests

Calibration Software and specified test equipment is required to perform the adjustments, and can be

used to automate the performance verification testing. Information on how to obtain this software can

be found at

http://www.agilent.com/find/calibrationsoftware

Utilities Required

None

Adjustments Required

None

Performance Testing Required

None

A full calibration is required to assure the instrument meets all specifications

The end user must ultimately determine whether they want a full calibration to be performed after the

installation of this upgrade or not. If a full calibration is required, arrangements regarding the level of

calibration must be made between the end user and the calibration provider.

For assistance, contact your nearest Agilent Technologies Sales and Service Office. To find your local

Agilent office access the following URL, or if in the United States, call the following telephone

number:

http://www.agilent.com/find/assist

1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Keysight Messgerät Handbücher

Keysight

Keysight 34420A Bedienungsanleitung

Keysight

Keysight Y1276A Kurzanleitung

Keysight

Keysight 537A Kurzanleitung

Keysight

Keysight N9322C Handbuch

Keysight

Keysight CalPod 855 A Series Bedienungsanleitung

Keysight

Keysight N9040B Option 513 Bedienungsanleitung

Keysight

Keysight 8990B Bedienungsanleitung

Keysight

Keysight CX3322A Benutzerhandbuch

Keysight

Keysight M9290A Bedienungsanleitung

Keysight

Keysight 85024A Handbuch

Keysight

Keysight N5221A Bedienungsanleitung

Keysight

Keysight N6705C Service-Handbuch

Keysight

Keysight MXA Series Installations- und Betriebshandbuch

Keysight

Keysight M9601A Bedienerhandbuch

Keysight

Keysight N6854A Bedienungsanleitung

Keysight

Keysight M3102A PXIe Bedienungsanleitung

Keysight

Keysight E5063A Bedienungsanleitung

Keysight

Keysight N1911A Betriebsanleitung

Keysight

Keysight N9030B Installations- und Betriebshandbuch

Keysight

Keysight U1281A Bedienungsanleitung

Keysight

Keysight 1146B Bedienungsanleitung

Keysight

Keysight PNA Series Montage- und Wartungsanleitung

Keysight

Keysight M9703B Benutzerhandbuch

Keysight

Keysight N1913B EPM Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung