Keysight N9010AK-MTU Installations- und Betriebshandbuch

Option MTU, MultiTouch User Interface Upgrade Kit

Option MTP, MultiTouch User Interface Upgrade Kit

with PC7 CPU

Keysight Technologies

N9010A EXA Signal Analyzer

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9010-90072

Edition

Edition 1, June 2016

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9010-90072 3

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

Introduction

This installation note explains how to install the hardware and licenses to add the MultiTouch user

interface to N9010A EXA signal analyzers.

This installation note supports two kits:

N9010AK-MTU - MultiTouch User Interface Upgrade

N9010AK-MTP - MultiTouch User Interface Upgrade with PC7 CPU

The N9010AK-MTU should only be installed on N9010As that already have the PC6 or PC7 CPU.

This kit includes a new SSD, to ensure that when a disk drive recovery is performed, the software

version recovered will be new enough to recognize the MultiTouch front panel assembly.

The N9010AK-MTP should be installed on N9010As that do not have a PC6 or PC7 CPU. A PC7

CPU is included in this kit, along with a new SSD.

Part of the upgrade process is the license transformation process, which creates new licenses to

replace those of the existing measurement applications. This is because older measurement

application licenses whose model numbers end in the letters "A" or "B" (for example, N9071A or

N9082B) will not work with the new MultiTouch user interface. The license transformation process

will replace "A" and "B" licenses with their equivalent "C" license. For example, N9071A-2FP will be

replaced with N9071C-2FP and N9082B-1FP will be replaced with N9082C-1FP.

Products Affected: N9010A EXA Signal Analyzer

Serial Numbers: All

To Be Performed By: (X) Keysight Service Center

( ) Personnel Qualified by Keysight

( ) Customer

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

2.5 Hours

3.0 Hours

4.0 Hours

4Installation Note N9010-90072

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

IMPORTANT Once this upgrade is performed, the analyzer will only recognize

measurement applications whose model number ends in a "C". For example,

the N9068C, Phase Noise measurement application or the N9071C

GSM/EDGE measurement application.

If the current version of instrument software does not support one of the

transformed licenses, the description as displayed in the Show System

screen will include the phrase "Dormant License UI Conversion". For example,

"N9064A Dormant License UI Conversion, VXA app".

The hardware included in the kit may come in several boxes inside the shipping container

Installation Note N9010-90072 5

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

N9010AK-MTU, MultiTouch User Interface Upgrade Kit Parts List

Quantity Description Keysight Part Number

1 Front Frame Assembly, MultiTouch, Light Color N9020-60261

1 Trim Strip, Top, Benchtop, Light Color N9020-40017

1 Trim Strip, Top, Opt PRC, Light Color N9020-40019

1Vibration Mounta

a. These items will not be needed when upgrading an N9010A.

0460-2725

2 Trim, Side, 177.0 H 5041-9172

1 Plug, Dome, 0.312 in. diameter, black 6960-0076

1Core Bracket, TopaN9020-00071

1Core Bracket, BottomaN9020-00072

1 Knob, RPG, Large W1312-40017

1 Solid State Drive Replacement, WES7 ------------

3Screws, M3 x 0.5 (8 mm long) pan heada0515-0372

9 Screws, M3 x 0.5 (8 mm long) flat head 0515-2032

1 Nameplate, 3.6 GHz, MultiTouch, N9010A N9010-80030

1 Nameplate, 7 GHz, MultiTouch, N9010A N9010-80031

1 Nameplate, 13.6 GHz, MultiTouch, N9010A N9010-80032

1 Nameplate, 26.5 GHz, MultiTouch, N9010A N9010-80033

1 Nameplate, 32 GHz, MultiTouch, N9010A N9010-80034

1 Nameplate, 44 GHz, MultiTouch, N9010A N9010-80035

1 Overlay, Connector, Blank, quartz gray N9020-80140

1 Overlay, Keypad, quartz gray N9020-80165

1 Overlay, Keypad, no EXM port, quartz gray N9020-80167

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate Envelope 5967-7169

1 Installation Note This note

6Installation Note N9010-90072

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

N9010AK-MTP, MultiTouch User Interface with PC7 CPU Upgrade Kit Parts List

Quantity Description Keysight Part Number

1 Front Frame Assembly, MultiTouch, Light Color N9020-60261

1 Trim Strip, Top, Benchtop, Light Color N9020-40017

1 Trim Strip, Top, Opt PRC, Light Color N9020-40019

2 Trim, Side, 177.0 H 5041-9172

1 Plug, Dome, 0.312 in. diameter, black 6960-0076

1 Knob, RPG, Large W1312-40017

1 CPU Module 2.2 GHz Dual Core Celeron, 8 GB RAM W1312-60210

1 Tray Assembly, solid state drive, 160 GB W1312-60302

9 Screws, M3 x 0.5 (8 mm long) flat head 0515-2032

1 Nameplate, 3.6 GHz, MultiTouch, N9010A N9010-80030

1 Nameplate, 7 GHz, MultiTouch, N9010A N9010-80031

1 Nameplate, 13.6 GHz, MultiTouch, N9010A N9010-80032

1 Nameplate, 26.5 GHz, MultiTouch, N9010A N9010-80033

1 Nameplate, 32 GHz, MultiTouch, N9010A N9010-80034

1 Nameplate, 44 GHz, MultiTouch, N9010A N9010-80035

1 Overlay, Connector, Blank, quartz gray N9020-80140

1 Overlay, Keypad, quartz gray N9020-80165

1 Overlay, Keypad, no EXM port, quartz gray N9020-80167

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate Envelope 5967-7169

1 Installation Note This note

Installation Note N9010-90072 7

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

Tools Required

— T-10 TORX Driver

— T-20 TORX Driver

— 5/16-inch torque wrench

— Deep 5/16-inch socket wrench

— ¼-inch open-end wrench

— Scissors or knife

—Diagonalcutters

— Microsoft Windows based personal computer with internet access and USB port

— USB storage device with > 2 GB free memory

Initial Instrument Functionality Check

Power on the instrument and allow the instrument to boot up. Run an alignment and display the

measurement screen. (The instrument will probably display a spectrum analyzer screen and you will

see the instrument sweeping.)

There should be no alignment failures. If there are failures, investigate and fix the problem before

continuing.

Before you disassemble the instrument, turn the power switch to Standby. After the instrument

has completely shut down, unplug the instrument. Failure to unplug the instrument can result in

personal injury.

Electrostatic discharge (ESD) can damage or destroy electronic components. All work on

electronic assemblies should be performed at a static-safe workstation. Refer to the

documentation that pertains to your instrument for information about static-safe workstations

and ordering static-safe accessories.

8Installation Note N9010-90072

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

Installation Procedure

Analyzer Information

1. Connect a power cord to the analyzer and turn on the analyzer.

2. After the analyzer has completed turning on, press System, Show, System. Make note of the

following information from the Show System screen:

Product Number: _____________

Serial Number: ______________

Instrument S/W Revision: ______________

3. Check for the presence of one of the following options listed below in the Show System

screen. Put a check mark or “X” after the option listed below that appears in the Show System

screen.

N9010A-PC1_____

N9010A-PC2_____

N9010A-PC3_____

N9010A-PC4_____

N9010A-PC5_____

N9010A-PC6_____

N9010A-PC7_____

N9010A-532_____

N9010A-544_____

N9010A-EXM_____

4. Refer to the data in step 2 above. If the Product Number is not N9010A, do not proceed with

the installation of this kit. This kit is to be installed only on N9010A signal analyzers.

5. Refer to the data in step 3 above. If upgrade product N9010A-MTU is being installed and the

currently installed CPU is either N9010A-PC1, N9010A-PC2, N9010A-PC3, N9010A-PC4, or

N9010A-PC5, do not proceed with the installation of this kit. This kit is to be installed only on

N9010A signal analyzers with N9010A-PC6 or N9010A-PC7 CPUs.

6. Refer to the data in step 3 above. If the upgrade product N9010A-MTP is being installed and

the currently installed CPU is N9010A-PC6 or N9010A-PC7, do not proceed with the

installation of this kit. This kit is to be installed only on N9010A signal analyzers with

N9010A-PC1, N9010A-PC2, N9010A-PC3, N9010A-PC4, or N9010A-PC5 CPUs.

7. Refer to the data in step 3 above. If Option N9010A-EXM is installed, there will be additional

steps required to remove and replace the front panel assembly.

Installation Note N9010-90072 9

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

License Key Backup

In order for the instrument being upgraded to keep the same option configuration that it had prior

to the upgrade, it is mandatory that the licenses be transferred from the original disk drive to the

new disk drive. In most cases, these licenses will be automatically copied from the Midplane board

assembly. However, there may be instances where the automatic copying process will not work.

Therefore, the license keys will also be backed up for later restoration on the new disk drive.

1. Connect a mouse and external keyboard to the analyzer using the rear panel USB ports.

2. Locate a USB storage device. Perform a virus scan on this device before use.

3. Create a folder on the USB storage device with the folder name "Licenses" followed by the

model number and serial number of the analyzer being upgraded. For example,

"Licenses_N9010A_MY50060101"

4. Insert the USB storage device into one of the analyzer's USB ports.

5. Using the mouse, navigate to the folder C:\Program Files\Agilent\licensing.

6. Change the folder's properties so that hidden files can be viewed.

a. If the operating system is WinXP, click on Tools and select Folder Options. Select the View

tab. In the Advanced Settings window, under Hidden files and folders, select "Show hidden

files and folders".

b. If the operating system is Windows Embedded Standard 7 (WES7), click on Organize and

select Folder and search options. Select the View tab. In the Advanced Settings window,

under Hidden files and folders, select "Show hidden files and folders".

7. Copy the contents of the C:\Program Files\Agilent\licensing folder to the Licenses… folder

created on the USB storage device.

a. To select all of the licenses in the folder, click on any of the licenses and then press Ctrl-A

on the external keyboard.

b. To copy the selected files, press Ctrl-C.

c. Navigate to the "Licenses_..." folder on the USB storage device for the instrument being

upgraded and press Ctrl-V to paste all the licenses into the folder.

10 Installation Note N9010-90072

Option MTU and MTP, MultiTouch User Interface Upgrade Kits

Backup Calibration Data

There are three different backup procedures that might need to be followed. Which backup

procedure to be run will depend on the software version that currently exists in the instrument

being upgraded.

To determine which calibration data backup procedure needs to be run compare the current

instrument software version that was recorded in the Analyzer Information section step 2 of this

document and follow the steps outlined below for that version.

S/W Revision Less Than A.01.55

Instruments with a software version older than A.01.55 will first need to have the software updated

to the latest version prior to being able to backup the instrument calibration data. See the Software

Updates section of this document for instructions on updating the instrument software.

Once the software has been updated, use the calibration data backup procedure under the heading

"S/W Revision Greater Than A.02.00".

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Keysight Messgerät Handbücher

Keysight

Keysight M9601A Benutzerhandbuch

Keysight

Keysight 42941A Bedienungsanleitung

Keysight

Keysight U1401B Bedienungsanleitung

Keysight

Keysight PNA-X N5241B Handbuch

Keysight

Keysight x series Bedienungsanleitung

Keysight

Keysight N5227B Bedienungsanleitung

Keysight

Keysight 478A Service-Handbuch

Keysight

Keysight x-series Produktinformationsblatt

Keysight

Keysight U8903B Bedienungsanleitung

Keysight

Keysight E4990A Referenzhandbuch

Keysight

Keysight E5080A Bedienungsanleitung

Keysight

Keysight M9290A Bedienungsanleitung

Keysight

Keysight N2862B Bedienungsanleitung

Keysight

Keysight N9010B EXA Installations- und Betriebshandbuch

Keysight

Keysight DOCSIS 3.1 Bedienungsanleitung

Keysight

Keysight B2980B Series Bedienungsanleitung

Keysight

Keysight N437 Series Handbuch

Keysight

Keysight E4991B Bedienungsanleitung

Keysight

Keysight N9912A Bedienungsanleitung

Keysight

Keysight U8903A Bedienungsanleitung

Keysight

Keysight N9340B Bedienungsanleitung

Keysight

Keysight M9709A Benutzerhandbuch

Keysight

Keysight N5227BU-420 Bedienungsanleitung

Keysight

Keysight M9703A Series Benutzerhandbuch

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung