Keysight N9010B EXA Installations- und Betriebshandbuch

Option YAS

Y-Axis Screen Video Out

Keysight N9010B EXA and

N9020B MXA Signal Analyzers

N9048B PXE EMI Receiver

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9020-90272

Edition

Edition 1, October 2018

Supersedes February 2018

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9020-90272 3

Option YAS Installation Kit

Products Affected: N9010B EXA Signal Analyzer

N9020B MXA Signal Analyzer

N9048B PXE EMI Receiver

Serial Numbers: All

Options

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysight

(X) Customer

Estimated Installation Time:

Estimated Adjustment and Verification Time:

0.5 Hours

4Installation Note N9020-90272

Option YAS Installation Kit

Introduction

This kit contains all of the instructions required to install Option YAS on Keysight EXA and MXA

signal analyzers and PXE EMI receivers. Option YAS enables the ANALOG OUT port to provide a

Y-Axis screen video output.

The rear panel ANALOG OUT port is present on all EXA and MXA signal analyzers and PXE EMI

receivers, however Option YAS must be enabled via a license file.

1. At the time of manufacture the hardware related to this option was fully

adjusted and the option performance was verified to be within its warranted

specifications. Within one year of the initial calibration date of the instrument

this option is fully calibrated with no further adjustment or verification testing.

To determine the initial calibration date, locate the original calibration

certificate that was shipped with the instrument at the time of purchase. The

Date of Calibration is printed on the original calibration certificate.

To ensure that this newly installed option has been installed properly, the

procedure that follows includes a functional check.

2. The latest revision of the X-Series signal analyzer software may be

downloaded from:

http://www.keysight.com/find/Xseries_software

3. This option is licensed for one instrument model/serial number combination.

The license key will only install on the designated instrument.

Installation Note N9020-90272 5

Option YAS Installation Kit

Contents

Tools Required for Installation

— Personal computer with internet access and USB port

— USB storage device with >2GB free memory

Tools Required for Manual Operation Verification

—Voltmeter

— Test cable, BNC (used to connect voltmeter to the analyzer rear panel ANALOG OUT)

— Banana plug to BNC adapter (used to connect voltmeter to BNC cable)

Installation Procedure over USB

1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.

2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the

Certificate.

3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an

attached License File.

4. Locate a USB storage device. Perform a virus scan on this device before use.

5. Save the License File to the root directory of the USB Storage Device.

6. Connect the USB Storage Device to the signal analyzer USB port. Windows will detect the new

hardware and may display the configuration menu shown in Figure 1. This menu may be

configured according to your preferences.

Quantity Description Keysight Part Number

1 Installation Note This note

1 Option Upgrade Entitlement Certificate 5964-5178

6Installation Note N9020-90272

Option YAS Installation Kit

Figure 1 USB Storage Device Configuration Menu

7. The signal analyzer will automatically consume the License File. (This may take a few minutes)

When the License File is consumed the Keysight License Manager will display a “Successful

License Installation” message similar to the one shown in Figure 2.

Figure 2 Successful License Installation

Alternate Installation Procedure

The License File can be manually installed over USB or LAN by placing the license file in the

following folder on the signal analyzer

C:\Program Files\Agilent\licensing

Verify the Installation

1. Cycle the power on the signal analyzer.

2. Press System, Show System to display a list of installed options.

3. Verify that the newly installed option appears on the list.

Installation Note N9020-90272 7

Option YAS Installation Kit

Manually Verify Operation

1. Preset X-Series analyzer. Assure mode is Spectrum Analyzer.

2. Display the 50 MHz calibrator signal. Press Input/Output, RF Calibrator, 50 MHz. Press FREQ,

Center Frequency, key in 50 MHz. Press Span, Zero Span. You should see a flat line across the

display at −25 dBm.

3. Press AMPTD, Ref Level, and key in −25 dBm. The displayed signal level should be at the top

graticule line.

4. Press Input/Output, Output, Analog Out, Screen Video.

5. Connect a voltmeter, set to measure DC volts, to the analyzer rear panel ANALOG OUT

connector.

6. The voltmeter should measure 1V.

7. Increase the Ref Level to −15 dBm. The signal should drop one graticule division on screen and

the voltmeter reading should be 0.9 V.

8. This test is sufficient to determine if the output circuitry is working properly for all Analog Out

signal selections.

8Installation Note N9020-90272

Option YAS Installation Kit

Utilities, Adjustments, and Performance Verification Tests

Calibration Software and specified test equipment is required to perform the adjustments, and can

be used to automate the performance verification testing. Information on how to obtain this

software can be found at

http://www.keysight.com/find/calibrationsoftware

Utilities Required

None

Adjustments Required

None

Performance Testing Required

None

A full calibration is required to assure the instrument meets all specifications

The end user must ultimately determine whether they want a full calibration to be performed after

the installation of this upgrade or not. If a full calibration is required, arrangements regarding the

level of calibration must be made between the end user and the calibration provider.

For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your

local Keysight office access the following URL, or if in the United States, call the following

telephone number:

http://www.keysight.com/find/assist

1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)

This information is subject to change

without notice.

Edition 1, October 2018

N9020-90272

www.keysight.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Keysight Messgerät Handbücher

Keysight

Keysight x series Kurzanleitung

Keysight

Keysight 8990B Betriebsanleitung

Keysight

Keysight E4981A Bedienungsanleitung

Keysight

Keysight B2980 Series Betriebsanleitung

Keysight

Keysight M9614A Bedienerhandbuch

Keysight

Keysight N9322C Handbuch

Keysight

Keysight x series Bedienungsanleitung

Keysight

Keysight x series Installations- und Betriebshandbuch

Keysight

Keysight U1190A Series Bedienungsanleitung

Keysight

Keysight x series Bedienungsanleitung

Keysight

Keysight N9320B Handbuch

Keysight

Keysight B2980A Series Installationsanleitung

Keysight

Keysight N5222-60119 Installations- und Betriebshandbuch

Keysight

Keysight N9038A Bedienungsanleitung

Keysight

Keysight U8903A Bedienungsanleitung

Keysight

Keysight 3458A Betriebsanleitung

Keysight

Keysight N432A Bedienungsanleitung

Keysight

Keysight N5221A Betriebsanleitung

Keysight

Keysight W2630 Series Bedienungsanleitung

Keysight

Keysight PXA N9030A Installations- und Betriebshandbuch

Keysight

Keysight N9030A Bedienungsanleitung

Keysight

Keysight N774 C Series Betriebsanleitung

Keysight

Keysight Y1301A Bedienungsanleitung

Keysight

Keysight E5071C ENA Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung