Keysight N9030B Installations- und Betriebshandbuch

Keysight Technologies

N9030B Signal Analyzers

Option FBP, Full Bypass Path

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9030-90122

Edition

Edition 1, November 2019

Supersedes none

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9030-90122 3

Option FBP, Full Bypass Path

Introduction

This installation note explains how to license, adjust, and verify performance of Option FBP, Full

Bypass Path on N9030B instruments that contain Option B2X or B5X and Option MPB and LNP.

Option FBP provides a signal path through the instrument front end when the start frequency is

3.6 GHz or greater, where both the Preselector and the Low Band Assembly are bypassed, which

results in low signal path loss and better sensitivity.

When Full Bypass Path is turned on, the Option MPB, Microwave Preselector Bypass is set to

bypass the Preselector; and the Option LNP, Low Noise Path is set to bypass the Low Band Switch.

In order for this FBP path to turn on, the start frequency must be greater than 3.6 GHz and the

Preamp must be turned off.

The option is licensed for one instrument model number/serial number combination. The license

file that is downloaded from the web will only install on the designated instrument.

Products Affected N9030B, PXA Signal Analyzer

Serial Numbers:

Options Required:

Restrictions:

All

N9030B-B2X or B5X

N9030B-MPB and N9030B-LNP

Cannot be installed on instruments with Option 503

To Be Performed By: (X) Keysight Service Center

( ) Personnel Qualified by Keysight

( ) Customer

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

1.0 Hours

4.0 Hours

2.0 Hours

4Installation Note N9030-90122

Option FBP, Full Bypass Path

Contents

Tools Required

— Personal computer with internet access and USB port

— USB storage device with > 3 GB free memory

— Keysight Calibration and Adjustment Software, N7814A (revision E.24.00 or later required)

— Test equipment and computer supported by the Keysight Calibration and Adjustment Software

Quantity Description Keysight Part Number

1 Installation Note This note

1 Option Upgrade Entitlement Certificate 5964-5178

Installation Note N9030-90122 5

Option FBP, Full Bypass Path

Initial Instrument Functionality Check

1. Power on the instrument and allow the instrument to boot up, run the alignments and display

the measurement screen. The instrument will probably display a spectrum analyzer screen and

you will see the instrument sweeping.

2. There should be no alignment failures. If there are failures, investigate and fix the problem

before continuing.

Installation Procedure

Analyzer Information

1. Connect a power cord to the analyzer and turn on the analyzer.

2. After the analyzer has completed turning on, press System, Show System.

Make note of the following information from the Show System screen:

Product Number _______________

Serial Number _______________

Instrument S/W Revision _______________

3. Check for the presence of the options listed below in the Show System screen. Put a check

mark after each option listed below that appears in the show System menu.

N9030B-B2X _______________

N9030B-B5X _______________

N9030B-MPB _______________

N9030B-LNP _______________

4. Refer to the data in step 2 above. Verify that the Product Number in step 2 is appropriate for

the upgrade being installed:

If the Product Number in step 2 is not appropriate for the Option FBP upgrade, do not proceed

with the installation.

5. Refer to the data in step 2 above. If the instrument software is earlier than A.25.00, you must

upgrade to version A.25.00 or later. Keysight recommends that you update to the latest

instrument software version to ensure that you have the latest defect fixes. To check the latest

instrument software version, visit the following website:

http://www.keysight.com/find/xseries_software

Option FBP Upgrade Product Number (Step 2)

N9030BU-FBP N9030B

6Installation Note N9030-90122

Option FBP, Full Bypass Path

6. Refer to the data in step 3 above.

Verify that both N9030B-MPB and N9030B-LNP are checked (currently installed). Verify that

N9030B-B2X or N9030B-B5X is checked (currently installed).

If these options are not installed, do not proceed with the installation of this kit.

Installation Note N9030-90122 7

Option FBP, Full Bypass Path

License Installation Procedure over USB

1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.

2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the

Certificate.

3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an

attached License File.

4. Locate a USB storage device. Perform a virus scan on this device before use.

5. Save the License File to the root directory of the USB storage device.

6. Connect the USB storage device to the signal analyzer USB port. Windows will detect the new

hardware and may display the configuration menu shown in Figure 1. This menu may be

configured according to your preferences.

Figure 1 USB Storage Device Configuration Menu

7. The signal analyzer will automatically consume the License File (this may take a few minutes).

When the License File is consumed the Keysight License Manager will display a “Successful

License Installation” message as shown in Figure 2.

Figure 2 Successful License Installation

8Installation Note N9030-90122

Option FBP, Full Bypass Path

Alternate Installation Procedure

The License File can be manually installed over USB or LAN by placing the license file in the

following folder on the signal analyzer

C:\Program Files\Agilent\licensing

Verify the License Installation and Hardware

1. Cycle power on the signal analyzer and wait until the analyzer boots to the measurement

application screen.

2. Press System, Show System to display a list of installed options.

3. Verify that the installed options list contains the newly installed N9030B_FBP.

Installation Note N9030-90122 9

Option FBP, Full Bypass Path

Instrument Software Installation

This upgrade requires instrument software version A.25.00 or later.

To verify the current version, press System, Show System and look for the "Instrument S/W

Revision".

The latest revision of the X-Series Signal Analyzers software may be downloaded from:

http://www.keysight.com/find/xseries_software

Verify Option FBP Functionality

1. Press MODE/MEAS, and select Spectrum Analyzer, Swept SA.

2. Press FREQ, Start Freq and key in 4 GHz. Press Stop Freq and key in 5 GHz. This assures the

start frequency is above 3.6 GHz, which is required in order to turn on the Full Bypass Path.

3. Press AMPTD, Signal Path and ensure Internal Preamp is set to Off. This is required in order to

turn on the Full Bypass Path.

4. Press uW Path Control, and select Full Bypass Enable. You will hear the bypass switch click.

5. See Figure 3, and notice the Meas Bar at the top middle of screen shows uW Path:FByp On

Figure 3 Meas Bar Full Bypass On

10 Installation Note N9030-90122

Option FBP, Full Bypass Path

Utilities, Adjustments, and Performance Verification Tests

Utilities Required

None

Adjustments Required

Performance Testing Required

Utilities Required

For assistance, contact your nearest Keysight Technologies Sales and Service Office.

To find your local Keysight office access the following URL, or if in the United States, call the

following telephone number:

http://www.keysight.com/find/assist

1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)

Adjustment Name

Frequency Response Above 3.6 GHz Full Bypass Path

IF Frequency Response UWBIF Full Bypass Path

IF Phase Linearity

Verification Test Name

Frequency Response Above 3.6 GHz Full Bypass Path Functional Test

Utility Name

IF Frequency Response UWBIF Check (Utility) and print the output file

IF Phase Linearity Utility and print the output file

Andere Handbücher für N9030B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Keysight Messgerät Handbücher

Keysight

Keysight N1914A Bedienungsanleitung

Keysight

Keysight M9383B VXG-m Bedienungsanleitung

Keysight

Keysight E5061B Bedienungsanleitung

Keysight

Keysight U8903A Bedienungsanleitung

Keysight

Keysight U1461A Bedienungsanleitung

Keysight

Keysight PD1000A Bedienungsanleitung

Keysight

Keysight N9340B Bedienungsanleitung

Keysight

Keysight 16034H Bedienungsanleitung

Keysight

Keysight x series Bedienungsanleitung

Keysight

Keysight 16861A Bedienungsanleitung

Keysight

Keysight U1211A Bedienungsanleitung

Keysight

Keysight M9601A Bedienerhandbuch

Keysight

Keysight 34420A Bedienungsanleitung

Keysight

Keysight M9703A Series Kurzanleitung

Keysight

Keysight 3458A Betriebsanleitung

Keysight

Keysight U8903A Bedienungsanleitung

Keysight

Keysight 16196A Bedienungsanleitung

Keysight

Keysight B2980B Series Bedienungsanleitung

Keysight

Keysight N432A Bedienungsanleitung

Keysight

Keysight Y1301A Bedienungsanleitung

Keysight

Keysight M9392A Benutzerhandbuch

Keysight

Keysight PNA E8362C Bedienungsanleitung

Keysight

Keysight N1913 Bedienungsanleitung

Keysight

Keysight N5241AU- 927 Installations- und Betriebshandbuch

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung