Keysight U8903A Bedienungsanleitung

Keysight U8903A

Audio Analyzer Demonstration Procedure

This document demonstrates ve simple

examples of using the U8903A. They are:

– GUI intuitiveness and shallow menu tree

– Loop test

– FFT analysis

– Time domain graph analysis

– Frequency or amplitude sweep analysis

Contents

Demonstration Preparation 2

Demo 1: GUI Intuitiveness and

Shallow Menu Tree

Demo 2: Loop Test 6

Demo 3: FFT Analysis 8

Demo 4: Time Domain Graph

Analysis

Demo 5: Frequency or Amplitude

Sweep Analysis

Demonstration Preparation

The following instruments

are used in this demon-

stration guide:

– U8903A Audio Analyzer

– One BNC cable

– One XLR cable (optional)

– Projector or PC monitor with

VGA cable – if you have a large

crowd

1. GUI Intuitiveness and Shallow Menu Tree

Objective:

To demonstrate the features, capabilities, and intuitiveness of the

Graphical User Interface (GUI) and menu tree.

1. Switch [ON] the equipment.

2. If you have a large crowd and a projector or PC monitor is available

in the meeting room, connect the VGA cable (from the projector/ PC

monitor input) to the VGA output from the equipment as shown in

Figure 1.

Note: Once connected, the projector/PC monitor will show the same

display as seen on the equipment front panel.

PREREQUISITE:

Figure 1. Keysight U8903A audio analyzer rear panel view

02 | Keysight | Audio Analyzer Demonstration Procedure - Data Sheet

PROCEDURE:

Generator setup

1. Press [Generator] to activate the Generator function.

2. Use the arrow keys to select Channel 1 and Channel 2 of the Generator.

Note: The active channel will be highlighted (see Figure 2).

3. Use the Generator menu to create various settings for audio signal generation, with waveform type, frequency,

amplitude, DC offset, and output as the main settings.

4. Press [Waveform] to show the various waveforms that can be generated such as Sine, Variable Phase, Dual Sine

(different frequency but same amplitude), Noise, DC, Multitones (60 Tones), Square, and Arbitrary.

5. To return to the previous menu tree, press [Return].

6. Press [Output Settings] to access the Generator settings on the Output Type – Balance or Unbalanced and

Impedance.

Note: All the selections made will be reected on the Generator screen.

7. Press [Frequency] and [Amplitude] to change the value of the frequency and amplitude for the signal to be

generated.

Note: You can key in the value from the alphanumeric keyboard in the front panel, or rotate the knob to get to a

higher or lower value. To conrm the value, press [Enter] on the arrow key.

Analyzer setup

8. Press [Analyzer] to activate the Analyzer function.

9. Repeat Step 2 to choose which Analyzer channel to be activated (see Figure 3).

10. Use the Analyzer menu to select the measurement functions, units, and measurement settings, and to set the

reference values as main settings.

Figure 2. Screenshot when Channel 1 is active Figure 3. Screenshot when Channel 2 is active

03 | Keysight | Audio Analyzer Demonstration Procedure - Data Sheet

PROCEDURE:

Figure 4. Three filters combined in Analyzer Channel 1

Function 1 (First

measurement parameter)

Function 2 (Second

measurement parameter)

11. Function 1 indicates the rst measurement parameter and Function 2 indicates the second measurement

parameter.

(Figure 4 shows that Function 1 refers to Frequency measurement while Function 2 refers to Vac measurement).

12. Press [Function 1] to select Frequency, Vac, or Vdc measurement parameter.

13. Press [Function 2] to select Frequency, Vac, Vdc, SNR, Noise Level, SINAD, THD+N Ratio, THD+N Level,

X-talk (Crosstalk), SMPTE, DFDs, and Phase measurements.

14. Press [Units] to select the measurement engineering unit for Function 1 and Function 2 measurement.

15. Press [Analyzer Settings] to select Coupling, Detector, Filter, Input Type, and Range settings.

– Press [Coupling] to select AC or DC coupling.

– Press [Detector] to select RMS, QPK, or Peak to Peak detector.

– Press [Filter] to select None, LP (Low Pass), HP (High Pass), or Weighting lters.

– Press [Input Type] to select Balance or Unbalanced input.

16. To show the different lters, combine the LP, HP, and Weighting lters in one analyzer channel.

– Press [Filter] > [LP] and select 15 kHz.

– Press [HP] > 22 kHz.

– Press [Weighting] > A-Weighting.

– The 15 kHz and 22 kHz will create a bandpass lter. Create an A-Weighting lter in the bandpass lter

(see Figure 4).

Note: You can combine a maximum of three different lters, that is, one lter from each lter category.

– Before proceeding to the next demonstration, “Loop Test”, clear the lter by pressing [Filter] > [None].

Press [Rel/Ref] for ratio measurement.

17. Press [Rel/Ref] for ratio measurement.

18. To show the Generator and Analyzer on the same display screen, press [Display/Mode] under the

System panel (see Figure 5).

04 | Keysight | Audio Analyzer Demonstration Procedure - Data Sheet

POINTS TO MENTION:

– Easy to set up.

– User-friendly GUI and very intuitive.

– Shallow menu tree.

– Custom lter can be saved, recalled, and

created using MATLAB, Keysight VEE,

and other programming software, and

uploaded via USB, LAN, or GPIB.

– Can display both Generator and Analyzer

channel measurement functions on the

same screen.

Figure 5. Both Generator and Analyzer are displayed on

the same display screen

RESULTS:

5 | Keysight | Audio Analyzer Demonstration Procedure - Data Sheet

PROCEDURE:

Generator setup

1. Press [Generator] to activate the Generator function.

2. Use the arrow keys to select Channel 1 from the Generator or Analyzer menu.

3. By default, the output Frequency value and Amplitude value are xed at 1 kHz and 0 Vrms. (Recommended

to set at 1 Vrms.)

4. Press [CHANNEL] or [OUTPUT] to start the signal generation.

5. In Channel 1, the Generator status changes from “Stopped” to “Running”.

2. Loop Test

Objective:

To demonstrate the self-test feature of the audio analyzer. The Generator

channel creates the signal and loops the signal to the Analyzer channel

for measurements.

PREREQUISITE:

Figure 6. BNC cable connection diagram

BNC

1. Switch [ON] the equipment.

2. If you have a large crowd and a project/PC monitor is available in the

meeting room, connect the VGA cable (from the projector/ PC monitor

input) to the VGA output from the equipment as shown in Figure 1.

Note: Once connected, the projector/ PC monitor will show the same

display as seen on the equipment front panel.

3. Connect the Generator Channel 1 and the Analyzer 1 with BNC cable or

XLR cable (optional) (see Figure 6).

Note: A BNC connection indicates the connection is unbalanced. An XLR

connection indicates that the connection is balanced.

6 | Keysight | Audio Analyzer Demonstration Procedure - Data Sheet

RESULTS:

Figure 7. Both Generator channels can output two

different signals simultaneously

Figure 8. Both Analzyer channels can analyze two

different signals simultaneously

POINTS TO MENTION:

– Each of the channels works independently. Therefore, you can output two different signals

from each Generator and analyze two different signals independently.

PROCEDURE:

Analyzer setup

6. Press [Analyzer] to activate the Analyzer function.

7. You must activate the Analyzer Channel 1 by using the arrow key because the BNC connector is connected to

the Analyzer Channel 1 . By default, Function 1 and Function 2 are xed at Frequency measurement and Vac

measurement.

8. Press [CHANNEL] to activate the Generator function.

9. In Channel 1, the Analyzer status changes from “Stopped” to “Running” as shown above.

10. You can repeat the previous steps by changing the Generator and the Analyzer to Channel 2 after the BNC

cable is connect to Channel 2.

Note: You must physically connect the BNC cable to Channel 2 of the Generator and the Analyzer.

7 | Keysight | Audio Analyzer Demonstration Procedure - Data Sheet

3. FFT Analysis

To demonstrate the FFT analysis features in the audio analyzer.

Objective:

PREREQUISITE:

1. Switch [ON] the equipment.

2. If you have a large crowd and a project/PC monitor is available in the

meeting room, connect the VGA cable (from the projector/ PC monitor

input) to the VGA output from the equipment as shown in Figure 1.

Note: Once connected, the projector/ PC monitor will show the same

display as seen on the equipment front panel.

3. Connect the Generator Channel 1 and the Analyzer Channel 1 with the

BNC cable or XLR cable (optional)(see Figure 6).

Note: A BNC connection indicates that the connection is unbalanced. An

XLR connection indicates that the connection is balanced.

PROCEDURE:

Generator setup

1. Press [Generator] to activate the Generator function.

2. Use the arrow keys to select Channel 1 from the Generator or Analyzer menu.

3. By default, the output Frequency value and Amplitude value are xed at 1 kHz and 0 Vrms. (Recommended to

set at 1 Vrms.)

4. Press [CHANNEL] or [OUTPUT] to start the signal generation.

5. In Channel 1, the Generator status changes from “Stopped” to “Running” as shown below.

Figure 9. FFT analysis

8 | Keysight | Audio Analyzer Demonstration Procedure - Data Sheet

PROCEDURE:

Frequency domain setup

6. Press [Frequency Domain] .

7. Press [Monitor settings] to change the graph monitor settings (see Figure 10).

8. Ensure that the Channel 1 box is checked. Press DOWN arrow key and the monitor settings will be

highlighted sequentially (that is the Analysis Mode, Windows, etc). Press [ENTER] to activate the drop-down

menu from the Window and select Blackman-Harris.

9. Press DOWN arrow key to No. Of Points. Press [ENTER] to activate the drop-down menu and select

8192 points.

10. Press [Apply] to save the setting.

11. Go to [Axis settings] and change the axis setting (see Figure 11).

12. Press DOWN arrow key to X-Axis Right, press [ENTER] and enter 10 kHz from the alphanumeric keyboard.

Press [Apply] to save the setting.

13. Press [CHANNEL] to start the measurement.

Figure 10. Screenshot of monitor settings Figure 11. Screenshot of axis setting

9 | Keysight | Audio Analyzer Demonstration Procedure - Data Sheet

POINTS TO MENTION:

– You can save the graph raw data

points to USB external ash storage

in a .csv le format. You can then plot

the graph in Microsoft Excel.

RESULTS:

Figure 13. Screenshot of each harmonics result

Figure 12. Screenshot of the FFT plot

Press [Harmonics View] to display the level of each

signal harmonic component of the frequency do-

main analysis. You may congure the fundamental

frequency, select the channel, and enter the number

of harmonic components data that will be computed

in the table.

10 | Keysight | Audio Analyzer Demonstration Procedure - Data Sheet

Andere Handbücher für U8903A

Inhaltsverzeichnis

Andere Keysight Messgerät Handbücher

Keysight

Keysight B2900A Bedienungsanleitung

Keysight

Keysight PXA X Series Installations- und Betriebshandbuch

Keysight

Keysight N5227A Bedienungsanleitung

Keysight

Keysight U1190A Series Bedienungsanleitung

Keysight

Keysight N2795A Bedienungsanleitung

Keysight

Keysight N9340B Bedienungsanleitung

Keysight

Keysight V3500A Bedienungsanleitung

Keysight

Keysight ENA Series Bedienungsanleitung

Keysight

Keysight N9010AK-MTU Installations- und Betriebshandbuch

Keysight

Keysight E5061B Bedienungsanleitung

Keysight

Keysight A Series Bedienungsanleitung

Keysight

Keysight N5222-60118 Installations- und Betriebshandbuch

Keysight

Keysight x series Kurzanleitung

Keysight

Keysight 8990B Bedienungsanleitung

Keysight

Keysight InfiniiMax III+ Series Bedienungsanleitung

Keysight

Keysight E5061B Bedienungsanleitung

Keysight

Keysight 81960A Bedienungsanleitung

Keysight

Keysight CalPod 855 A Series Bedienungsanleitung

Keysight

Keysight N8262A Bedienungsanleitung

Keysight

Keysight N8973B Bedienungsanleitung

Keysight

Keysight 11590B Service-Handbuch

Keysight

Keysight EXA X-Series N9010A Bedienungsanleitung

Keysight

Keysight M9290A Bedienungsanleitung

Keysight

Keysight B2900A Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

ADTEK

ADTEK MW-5 Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung