Keysight N9030B Installations- und Betriebshandbuch

Keysight Technologies

N9030B Signal Analyzer

Option 107

Audio Input and Digitizer

Upgrade Kit

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9030-90111

Edition

Edition 2, October 2018

Supersedes none

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9030-90111 3

Option 107, Audio Input and Digitizer Upgrade Kit

Products Affected: N9030B, PXA Signal Analyzer

Serial Numbers: All

Option 107

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysight

(X) Customer

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Timea:

a.To ensure that this newly installed option is functioning properly, the procedure that follows includes the

requirement of performing certain adjustments and performance verification tests. However, the completion of

these tests does not guarantee that the instrument meets all advertised specifications.

Software and test equipment is required for making adjustments and for performance verification testing.

Information on how to obtain this software can be found at:

www.keysight.com/find/calibrationsoftware

While Keysight does recommend that a full calibration be performed after the installation of this upgrade, the

end user must ultimately determine whether they want this service or not. If a full calibration is required,

arrangements regarding the level of calibration must be made between the end user and the calibration

provider.

1.0 Hours

0.0 Hours

0.5 Hours

4Installation Note N9030-90111

Option 107, Audio Input and Digitizer Upgrade Kit

Introduction

This kit provides all parts and instructions necessary to install Option 107, Audio Input and

Digitizer, into the Keysight N9030B.

1. This upgrade kit is not compatible with N9030B PXA signal analyzers with any

of the following options currently installed:

N9030B-B5X - 510 MHz Analysis Bandwidth

N9030B-BBA - I/Q Baseband Inputs

2. This upgrade kit installation requires that you re-install instrument software.

The latest revision of the PXA Signal Analyzer software may be downloaded

from

http:/www.keysight.com/find/xseries_software

The instrument software must be installed AFTER the hardware in the kit is

installed. Follow the procedure in this document for redeeming and installing

the option upgrade license key.

3. The option is licensed for one instrument model/serial number combination.

The license key will only install on the designated instrument.

Installation Note N9030-90111 5

Option 107, Audio Input and Digitizer Upgrade Kit

Installation Kit Parts List

Quantity Description Keysight Part Number

1 Screw, FLT-HD Torx T10 M3 x 0.5 (6 mm long) 0515-1227

1 Lock Washer, Internal tooth 2190-0068

1 Hex Nut 15/32-32 Interface Board 2950-0035

1 Coaxial Cable Assembly w/Toroids N9020-60344

1 Cover Plate, Audio N9030-00004

1 PCA, Audio Digitizer N9030-60047

1 Overlay, Audio Input N9030-80062

1 Installation Note this note

1 Option Upgrade Entitlement Certificate n/a

6Installation Note N9030-90111

Option 107, Audio Input and Digitizer Upgrade Kit

Tools Required

— T-10 Torx Driver

— T-20 Torx Driver

— 5/16-inch torque wrench

— 1/4-inch open end wrench

— 1/4-inch socket on 4 lb torque wrench

—scissorsorknife

—diagonalcutters

— USB storage device with > 2 GB free memory

Before you disassemble the instrument, turn the power switch to Standby, wait until the

instrument has completely shut down, and unplug the instrument. Failure to unplug the

instrument can result in personal injury.

Electrostatic discharge (ESD) can damage or destroy electronic components. All work on

electronic assemblies should be performed at a static-safe workstation. Refer to the

documentation that pertains to your instrument for information about static-safe workstations

and ordering static-safe accessories.

Installation Note N9030-90111 7

Option 107, Audio Input and Digitizer Upgrade Kit

Installation Procedure

Instrument Cover Removal

1. Power down the instrument and wait for the standby light to come on. Disconnect the

instrument from ac power.

2. Refer to Figure 1. Using the T-20 driver, remove the 4 screws (1) (two on each side) that

attach the strap handles (2) on each side of the instrument.

3. Remove the four key locks from the instrument four bottom feet.

4. Remove the four instrument bottom feet.

5. Using the T-20 driver, remove the four screws (including washers) (3) that hold the rear feet

(4) in place.

6. Pull the instrument cover (5) off towards the rear of the instrument.

If the instrument is placed on its face during any of the following procedures, be sure to use a soft

surface or soft cloth to avoid damage to the front panel, keys, or input connector.

Make sure any adapters on the front panel are removed.

8Installation Note N9030-90111

Option 107, Audio Input and Digitizer Upgrade Kit

Figure 1 Instrument Outer Case Removal

Installation Note N9030-90111 9

Option 107, Audio Input and Digitizer Upgrade Kit

Top Brace Removal

1. Refer to Figure 2. To remove the top brace (1), use the T-10 driver to remove the twelve

panhead screws (3) (0515-0372) attaching the top brace to the chassis. Remove the twelve

screws (fourteen screws with Option B1X) (4) (0515-1946) attaching the top brace to the

boards.

Figure 2 Top Brace Removal

10 Installation Note N9030-90111

Option 107, Audio Input and Digitizer Upgrade Kit

Option 107 Hardware Installation

1. Refer to Figure 3. Locate and install the N9030-60047 Audio Digitizer PCA into slot 7.

Figure 3 Option 107 Audio Digitizer

Andere Handbücher für N9030B

Inhaltsverzeichnis

Andere Keysight Messgerät Handbücher

Keysight

Keysight x-series Produktinformationsblatt

Keysight

Keysight N5221A Bedienungsanleitung

Keysight

Keysight PD1000A Bedienungsanleitung

Keysight

Keysight A Series Bedienungsanleitung

Keysight

Keysight 8990B Bedienungsanleitung

Keysight

Keysight U1211A Bedienungsanleitung

Keysight

Keysight NFA Series Gebrauchs- und Pflegehandbuch

Keysight

Keysight E4990A Gebrauchs- und Pflegehandbuch

Keysight

Keysight MXA 902 Series Installations- und Betriebshandbuch

Keysight

Keysight PNA Series Montage- und Wartungsanleitung

Keysight

Keysight N9340B Bedienungsanleitung

Keysight

Keysight x series Kurzanleitung

Keysight

Keysight M8131A Bedienungsanleitung

Keysight

Keysight 3458A Betriebsanleitung

Keysight

Keysight U1211A Handbuch

Keysight

Keysight NFA Series Betriebsanleitung

Keysight

Keysight 81960A Bedienungsanleitung

Keysight

Keysight x series Bedienungsanleitung

Keysight

Keysight M9202A Benutzerhandbuch

Keysight

Keysight M9391A Bedienungsanleitung

Keysight

Keysight E5052B Bedienungsanleitung

Keysight

Keysight N5241AU- 927 Installations- und Betriebshandbuch

Keysight

Keysight x series Betriebsanleitung

Keysight

Keysight 16196A Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung