Kichler Lighting 42 STRATMOOR Bedienungsanleitung

  2*

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

Instruction Manual

42" StratmoorTM

A Kichler®Select™

ceiling fan

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local electrical

codes. Electrical installation should be

performed by a qualified licensed

electrician.

3. WARNING: Suitable for use with solid-

state speed controls.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting fixtures are not acceptable for fan

support and may need to be replaced,

consult a qualified electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use only CUL Listed outlet boxes

marked "FOR FAN SUPPORT".

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the floor.

7. Do not operate reversing switch while fan

blades are in motion. Fan must be turned

off and blades stopped before reversing

blade direction.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After making the electrical connections,

spliced conductors should be turned

upward and pushed carefully up into outlet

box. The wires should be spread apart with

the ground wire and white (common) wire

to one side with the black (load) wire to the

other side of the outlet box.

12. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be CUL Listed and marked suitable

for use with the model fan you are

installing. Switches must be CUL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

OR PERSONAL INJURY, MOUNT FAN TO OUTLET

BOX MARKED "ACCEPTABLE FOR FAN

SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE BRACKETS (ALSO

REFERRED TO AS FLANGES) DURING ASSEMBLY

OR AFTER INSTALLATION. DO NOT INSERT

OBJECTS IN THE PATH OF THE BLADES.

1. SAFETY RULES

3. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items:

a. Fan blades (5)

b. Ceiling mounting plate

c. Motor and hanger bracket assembly

d. Motor housing

e. Set of 5 blade brackets and Pre-Installed

mounting screws

f. Mounting plate

g. Switch housing

h. Part bag contents

1) Mounting hardware:

star washers (2), wire nuts (3),

machine screws (2), washers (2),

screws (2)

2) Blade attachment hardware:

screws (17), washers (17),

fiber washers (17)

3) Safety cable hardware:

wood screw, lock washer, flat washer

4) Pull chain and fob

5) Balance Kit

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

42" StratmoorTM

4. MOUNTING OPTIONS

If there isn't an existing UL (cUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1, 2 are examples of different ways to

mount the outlet box.

NOTE: Depending on the location you have

selected for installation, you may need to

purchase and install a "Joist Hanger" for the

support of the outlet box. Make sure the joist

hanger you purchase has been designed for

use with ceiling fans. (Fig. 3)

Outlet box

Fig. 1

Fig. 3

Outlet box

Fig. 2

Fig. 5

REMEMBER to turn off the power before you

begin.

To properly install your ceiling fan, follow the

steps below.

Step 1. Secure the ceiling mounting Plate to

the ceiling outlet box using screws and

washers included with your outlet box. (Fig. 4)

Step 2. Carefully lift the fan motor/hanger

plate assembly up to the ceiling mounting

plate and hang the assembly on the hook

attached to one end of the ceiling mounting

plate. See figure 5.

Fig. 4

5. HANGING THE FAN

CUL Listed

electrial box

Flat washers

Mounting screws

Ceiling mounting

plate

Motor

Hook

Hanger plate

Ceiling

mounting

plate

42" StratmoorTM

Fig. 6

6. ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock,

be sure you have turned off the power at the

main circuit panel.

Follow the steps below to connect the fan to

your household wiring. Use the wire

connecting nuts suppled with your fan. Secure

the connectors with electrical tape. Make sure

there are no loose wire strands or

connections.

Step 1. Connect the fan supply (black) wire to

the black household supply wire as shown in

Figure 6.

Step 2. Connect the neutral fan (white) wire to

the neutral household (white) wire.

Step 3. Connect the fan ground wire (green) to

the household ground wire.

Step 4. After connecting the wires, spread

them apart so that the green and white wires

are on one side of the outlet box and the black

wires is on the other side.

Step 5. Turn the connecting nuts upward and

push the wiring into the outlet box.

WARNING: TO REDUCE THE RISK OF PERSONAL INJURY AND TO INUSRE THE PROPER

OPERATION OF YOUR CEILING FAN. NEVER ATTACH THE BLADE ASSEMBLIES UNTIL THE

CEILING FAN HAS BEEN MOUNTING ON THE CEILING. DO NOT BEND THE BLADE ARMS

WHILE INSTALLING, BALANCING OR CLEANING THE FAN. DO NOT INSERT FOREIGN

OBJECTS BETWEEN ROTATING FAN BLADES.

BLK BLK

GRN

Wiring

box

Ground to

mounting

bracket

or downrod

Power lines 120v

Green ground

Fig. 7

Fig. 8

8. INSTALLING THE MOTOR HOUSING

Remove the four sets of nuts and washers

located on the mounting plate threaded studs.

Hang the motor assembly from the hook on

the ceiling mounting plate by placing the hook

into a hole on the mounting plate.

Place the wires and connections inside the

mounting plate and the ceiling mounting plate.

Swing the motor assembly up into position

under the ceiling mounting plate, align the

holes on the mounting bracket with the four

studs on the mounting plate and push the

motor assembly onto the studs. Secure with

the four nuts and washers you removed

earlier. (Fig. 7)

Mounting plate

Mounting

Plate

threaded

studs

Motor

housing

Ceiling mounting

plate

Screws

Motor assembly

Washer

Nut

Remove the four screws located on the

outside edge of the ceiling mounting plate.

Lift the Motor Housing up and align the

mounting holes in the housing to the mounting

holes on the ceiling mounting plate.

Insert each mounting screw rotating first one

side to the other and then tighten each screw

after all four have been started. (Fig. 8)

7. FINISHING THE INSTALLATION

42" StratmoorTM

Fig. 9

9. ATTACHING THE FAN BLADES

Fig. 10

Step 1. Place a blade on a blade bracket

aliening the mounting holes on each. Start

each set of mounting screws, washers and

fiber pads into each hole.

Make sure the blade is straight on the blade

bracket and tighten each mounting screw until

the fiber pad is slightly compressed.

Step 2. Attach each blade assembly to the

motor using the "Pre-installed" mounting

screws in the blade bracket. (Fig 9)

Repeat the above process for each blade

assembly.

Set of blade brackets

Blade

Fiber washers

Washers

Screws

Mounting plate

Mounting ring

10. INSTALLING THE SWITCH HOUSING

PLATE

1. Loosen two screws on the mounting ring

attached to the motor shaft and "remove" and

save the third screw. (Fig. 10)

2. Place the key holes on the mounting plate

over the 2 screws previously loosened from

the mounting ring, turn mounting plate until it

locks in place at the narrow section of the key

holes. Secure by tightening the 2 screws

previously loosened and the one previously

removed. (Fig. 10)

Fig. 11

11. INSTALLING THE SWITCH HOUSING

NOTE: Before continuing installation, confirm

that the power is still turning off at the main

circuit breaker or by removing the correct fuse.

Turning the power off using a wall switch is not

sufficient to prevent electrical shock.

1. While holding the switch housing under your

ceiling fan, push the square wire connectors

together. One from the fan and one from the

switch housing.

NOTE: These connectors are color coded and

will ONLY engage when the colored strips are

matched (aligned).

2. Carefully push all the wires into the switch

housing.

Attach the switch housing to the mounting

plate with the screws provided. Make sure

each screw is tight. (Fig. 11)

Switch housing

Wire connectors

Screws

Mounting plate

42" StratmoorTM

Fig. 12

Fig. 13

12. OPERATING INSTRUCTIONS

The pull chain controls the 3 speeds of your

ceiling fan.

1 pull = High, 2 pulls = Medium, 3 pulls = Low

and the 4th pull turns the motor off.

The Black Slide Switch on the side of the

switch housing controls the direction of the

blades "Forward and Reverse".

Warm weather - Forward (counter clockwise)

A downward airflow creates a cooling effect

as shown in Fig. 12. This allows you to set

your air conditioner on a warmer setting

without affecting your comfort.

Cool weather - Reverse (clockwise) An

upward airflow moves warm air off the ceiling

area as shown in Fig. 13. This allows you to

set your heating unit on a cooler setting

without affecting your comfort.

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting Starkk Bedienungsanleitung

Kichler Lighting

Kichler Lighting True Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300260/60-GENT Series Bedienungsanleitung

Kichler Lighting

Kichler Lighting Cameron Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lehr II Bedienungsanleitung

Kichler Lighting

Kichler Lighting KAPONO Bedienungsanleitung

Kichler Lighting

Kichler Lighting Porters Lake Bedienungsanleitung

Kichler Lighting

Kichler Lighting Logan Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch II Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting Eris Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35166 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Starkk 330180MWH Bedienungsanleitung

Kichler Lighting

Kichler Lighting Tide Weather+ Bedienungsanleitung

Kichler Lighting

Kichler Lighting Ried 300356 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Todo 330025 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Rivetta Bedienungsanleitung

Kichler Lighting

Kichler Lighting Seaside Bedienungsanleitung

Kichler Lighting

Kichler Lighting Hatteras Bay Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting Seaside 310181WZC Bedienungsanleitung

Kichler Lighting

Kichler Lighting PINION 60 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Chicago Bedienungsanleitung

Kichler Lighting

Kichler Lighting Golden Iridescence Bedienungsanleitung

Kichler Lighting

Kichler Lighting Decor InnesII 300130 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Terna 300230 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung