Kichler Lighting Chicago Bedienungsanleitung

ChicagoTM

Includes our new

CoolTouchTM Control System

Looks permanent, but goes wherever you go!

U.S. Patent Pending

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

A Kichler®Décor™ceiling fan

Designed to coordinate with a popular Kichler Lighting collection.

Instruction Manual

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

3. WARNING: To reduce the risk of electrical

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use the outlet boxes marked

"FOR FAN SUPPORT".

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the floor.

7. To operate the reverse function on this fan,

press the reverse button while the fan is

running.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After marking electrical connections,

spliced conductors should be turned

upward and pushed carefully up into outlet

box. The wires should be spread apart with

12. Electrical diagrams are for reference only.

Light kits that are not packed with the fan

must be marked suitable for use with the

model fan you are installing.Refer to the

Instructions packaged with the light kits and

switches for proper assembly.

NOTE: NOT SUITABLE FOR USE WITH SOLID-

STATE SPEED CONTROLS.

1. SAFETY RULES

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT FAN TO

OUTLET BOX MARKED "ACCEPTABLE FOR FAN

SUPPORT".

WARNING

All wiring must be in accordance with the

National Electrical Code, ANSI/NFPA70-1999

and local electrical codes. Electrical installa-

tion should be performed by a qualified

licensed electrician.

WARNING: To reduce the risk of fire,

electric shock, or personal injury, mount

this fan to outlet box marked "Acceptable

for Fan Support" and use mounting

screws provided with the outlet box. Most

outlet boxes commonly used for the sup-

port of light fixtures are not acceptable for

fan support and may need to be replaced.

Due to the complexity of the installation of

this fan, a qualified licensed electrician is

strongly recommended.

conductor of a fan identified as grounded

condutor to be connected to a grounded

conductor of power supply, conductor of fan

identified as ungrounded conductor to be

connected to an ungrounded conductor of

power supply,conductor of fan identified for

equipment grounding to be connected to an

equipment-grounding conductor.

breaker or fuse box before cleaning and

maintenace, attempting Installation.

shock and fire, do not use this fan with

any solid-state fan speed control device.

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE BRACKETS WHEN

INSTALLING THE BRACKETS, BALANCING THE

BLADES, OR CLEANING THE FAN. DO NOT

INSERT FOREIGN OBJECTS IN BETWEEN ROTAT-

ING FAN BLADES.

Philips screw driver

Slot screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

ChicagoTM

3. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items:

a. Fan blades (5)

b. Mounting bracket (1)

c. Canopy (1)

d. Ball/downrod assembly (1)

& extra downrod (1)

e. Coupling cover (1)

f. Fan assembly (1)

g. Blade brackets (5)

h. Mounting plate (1)

i. Switch housing (1)

j. Light kit (1)

k. Glass bowl (1)

l. Receiver +7 wire nuts

m. CoolTouch™ Control System

n. Canopy cover (1)

o. Bulbs (3)

p. Package hardware:

1) Mounting hardware:

a. wood screws (2), flat washers (2),

æææscrews(2),wire nuts(4)

2) Blade attachment hardware:

a. screws (16), flat washers (16),

æææfiber washers (16)

3) Blade bracket hardware:

a. screws (1)

4) Safety cable hardware:

a. wood screw (1), spring washer

(1), flat washer (1)

5) Balance kit

q. Decorative plate hardware:

decorative plate (1), finial (1),

light kit hardware (1)

4. MOUNTING OPTIONS

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1,2 and 3 are examples of different

ways to mount the outlet box.

NOTE: You may need a longer downrod to

maintain proper blade clearance when

installing on a steep, sloped ceiling. (Fig. 3)

To hang your fan where there is an existing

fixture but no ceiling joist, you may need a

joist hanging bracket as shown in Fig 4.

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

If there isn't an existing UL ( CUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

ChicagoTM

Fig. 7

Fig. 5

Fig. 6

Fig. 8

Screw

shipping block

Fan assembly

Washer

120V wires

Mounting screw

Electrial box

Mounting

bracket

Set Screw

Cross Pin

Hanger Ball

Downrod

Lock pin

Set screw

Hitch pin

5. HANGING THE FAN

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly:

Step 1. Remove the fan motor and housing

assembly from the protective plastic bag and

take the lower styrofoam packing pad out of

the carton. Place the styrofoam pad on the

floor, then place the fan assembly into the

styrofoam pad with the bottom of the motor

facing up. (The styrofoam pad serves as a

holder for the fan during the first stages of

assembly). Remove the plastic motor shipping

blocks and discard. (Fig. 5)

Step 2. Secure the mounting bracket to the

ceiling outlet box using screws and washers

provided with the outlet box. (Fig. 6)

Step 3. Use a screwdriver to loosen the cross

pin and remove it from downrod assembly.

Loosen the set screw and rotate the hanger

ball off the downrod. (Fig. 7)

Step 4. Loosen the two set screws and

remove the hitch pin and lock pin from the

motor coupling assembly. (Fig. 8)

Step 5. Carefully feed fan electrical wires up

through the downrod. Thread the downrod

onto the motor coupling until the hitch pin

holes are aligned. Next, replace hitch pin and

lock pin, and tighten both set screws. (Fig. 8)

Fig. 10

Registration slot

Fig. 9 Step 7. Now lift the motor assembly into

position and place the hanger ball into the

hanger bracket. Rotate until the “Check Tab”

has dropped into the “Registration Slot” and

seats firmly. (Fig. 10)

NOTE: The entire motor assembly should

not rotate if this is done correctly.

NOTE: Please make sure all set screws

are in place and tight before installation

the following steps.

Canopy cover

Downrod Canopy

Coupling cover

Step 6. Slip the coupling cover, canopy

cover and canopy onto the downrod. Rein-

stall hanger ball into the downrod and make

sure the cross pin is in place and set screw

on hanger ball is tight. Secure the coupling

cover is resting on the top of ceiling fan.

(Fig. 9)

ChicagoTM

Fig. 12

Fig. 13

Code switch

Receiver

Hanger

bracket

Battery Compartment

6. INSTALLATION OF SAFETY SUPPORT

( For Canadian Installation ONLY )

7. MAKE THE ELECTRIC CONNECTIONS

A safety support cable is provided to help prevent

the ceiling fan from failing, please install it as

follows.

Step 1. Attach the provided wood screw and

washers to the ceiling joist next to the mounting

bracket but do not tighten. (Fig. 11-1)

Step 2. Adjust the length of the safety cable to

reach the screw and washers by pulling the extra

cable through the cable clamp until the overall

length is correct, put the end of the cable back

through the cable clamp, forming a loop at the

end of the cable. Tighten the cable clamp

securely. Now, put the loop in the end of the

safety cable over the wood screw and under the

washer. Tighten the wood screw securely. See

Fig. 11-2

WARNING: To avoid possible electrical shock,

be sure the electricity is turned off at the main

circuit breaker or fuse box before wiring.

WARNING: If your house wires are different

colors than referenced in this manual, stop

immediately. A professional electrician is recom-

mended to determine proper wiring.

NOTE: The CoolTouch™ Control System is

equipped with 16 code combinations to prevent

possible interference from or to other remote

units. The frequency switches on your receiver

and transmitter have been preset at the factory.

Please recheck to make sure the switches on

the transmitter and receiver are set to the same

position, any combination of settings will position

the fan as long as each switch on the transmitter

and receiver are set to the same position. (Fig.

12) Changing the order of switches on each

switch block, changes the operational frequency.

Step 1. Insert the receiver into the mounting

bracket, with the flat toward the ceiling. (Fig. 13)

Step 2. Motor to Receiver Electrical Connec-

tions:

NOTE: Make all of the following connections

with “Wire Nut” connectors.

Connect the black wire from the fan to black wire

marded “TO MOTOR L” from the receiver. Con-

nect the white wire from the fan to the white wire

marked “TO MOTOR N” from the receiver.

Connect the blue wire from the fan to the blue

wire marked “For Bottom Light” from the

receiver. Place a plastic wire nut on the end of

the Orange Wire coming from the receiver

marked “For Upper Light”. Your ceiling fan is not

equipped with a Upper Light. Secure all the wire

connections with the plastic wire nut provided.

(Fig. 14 on the next page)

Fig. 11-2

Fig. 11-1

Ceiling

Support Brace

Outlet Box

Wood Screw

Flat Washer

Spring Washer

Wood Screw

Safety Cable Cable Clamp

Fig. 14

Fig. 15

Step 3. Remote Receiver to Outlet Box Electri-

cal Connections: Connect the black

(hot) wire from the ceiling to the black wire

marked "AC in L" from the receiver. Connect

the white(neutral) wire from the ceiling to the

white wire marked "AC in N" from the

Receiver. Secure the wire connections with

the plastic wire nuts provided. (Fig. 14)

Step 4. If your outlet box has a ground wire

(green or bare copper) connect it to the fan

ground wires. Secure the wire connection with

a plastic nut provided.

NOTE: Carefully tuck the wire connections up

into the outlet box. (Fig. 14)

NOTE: The transmitting unit must be installed

at a maximum distance of 30 feet from the

ceiling fan for proper signal transmission

between the transmitting unit and the fanʼs

receiving unit.

8. INSTALLING THE CEILING CANOPY

WARNING: One last time, make sure the “Check

Tab” at the bottom of the hanger bracket is prop-

erly seated in the “Registration Slot” on the side

of the hanger ball before attaching the canopy to

the bracket. Failure to properly seat the “Check

Tab” could damage the electrical wires when the

ceiling fan blade direction is changed while the

fan is running.

Step 1. Make sure all of the electrical connec-

tions are tucked neatly into ceiling outlet box.

Step 2. Slide the canopy up to ceiling fan and

onto the two screws on hanger bracket. Rotate

the canopy clockwise and tighten the two screws.

Next, while holding the canopy with one hand,

slide the canopy cover over the screws and

rotate clockwise until tight.

NOTE: You may need to adjust the canopy

mounting screws as necessary until the canopy

and canopy cover have a snug fit. (Fig. 15)

white (neutral)

Blue(for bottom light)

Ground wire

White("AC IN N")

Copper (ground)

White("to motor N")

Green or bare

White (neutral)

Black (motor)

Orange (For

upper light)

Blue(for bottom light)

Black ("to motor L")

Receiver

Black("AC" IN L")

Black (hot)

Outlex box

Canopy cover

Canopy

Screw

Hanger bracket

Outlet box

ChicagoTM

9. ATTACHING THE FAN BLADES

Fig. 16

Fig. 17

Fig. 18

10. INSTALLATING THE MOUNTING PLATE

Step 1 Attach the blade to the blade bracket

using the screws, washers and fiber washers

as shown in Figure 16. Start screw into

bracket. Repeat for the two remaining screws.

Blade

Blade bracket

Fiber washer

Metal washer

Screw

Fan assembly

Screw

Step 2. Place the key holes on the mounting

place over the remaining 2 screws on the

mounting ring, turn mounting plate until it locks

in place at the narrow section of the key holes.

Secure by tightening 2 screws and reinstalling

the third screw. (Fig. 18)

Note: If you would like to install the light fixture

that come with your ceiling fan, please skip to

step 12 and continue. If you want your ceiling

fan installed without the light fixture, follow step

11 and then skip to Step 14.

Step 1. Remove 1 of 3 screws on the mounting

ring and loosen the other 2 screws. Do not

remove (the mounting ring located on the

motor shaft).

Mounting ring

Screw

Mounting plate

Step 2. Make sure the blade is straight and

tighten each screw until fiber washer is

slightly compressed and all three screws

are secure. (Fig. 16)

Step 3. Fasten blade assembly to motor

using “pre-installed” mounting screws in the

blade bracket (Fig. 17)

Fig. 20

Fig. 19

12. INSTALLING THE LIGHT KIT

11. INSTALLING THE SWITCH HOUSING

Connection plug

Mounting plate

Switch housing

NOTE: Before continuing, make sure the power

is disconnected by turning off the circuit breaker

of removing the fuse at the circuit box.

Step 1. Loosen the 3 screws on the switch

house mounting plate.

Step 2. The square plastic wiring connectors

from the ceiling fan and the switch housing will

only fit together one way. Match up the color on

the side of the connectors, then push them

together until the snap engages.

Step 3. Tuck the connections neatly into the

switch housing. Align the key holes on the

switch housing with the screws on the mounting

plate. Turn the switch housing until it locks in

place at the narrow end of the key holes.

Tighten all 3 screws previously loosened.

(Fig. 19)

Step 1. Remove th finial NUT located in the

center of the switch housing. See Fig. 20.

Step 2. Remove the hex nut, lock washer and

metal washer from the light fixture mounting

stem.

Step 3. Feed the electrical wires from the light

fixture through the hole in the switch housing

(starting with th black wire first, it has a larger

connector). Threaded th light kit onto the

switch housing, add the metal washer, lock

washer and hex nut on the inside of the switch

housing and tighten securely. (Fig. 20)

NOTE: Please take the reverse module,

capacitor and 190w power limiter out of the

switch housing prior to threading the light kit to

switch housing.

ModelNo: PL-190B

AC120V 60HZ

PowerLimit

Max.190W(ON/OFF)

IncandescentorBallast

LIGHT/BLACK

Capacitor Limiter

Reverse module

Finial nut

White wire

Black wire

Light kit

Lock washer

Metal washer

Hexnut

Switch housing

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting Windham Bedienungsanleitung

Kichler Lighting

Kichler Lighting Imari 65 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35208 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Kittery Point Bedienungsanleitung

Kichler Lighting

Kichler Lighting POLA Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch Bedienungsanleitung

Kichler Lighting

Kichler Lighting Vassar 330002OZ Bedienungsanleitung

Kichler Lighting

Kichler Lighting Deckard Bedienungsanleitung

Kichler Lighting

Kichler Lighting Sola 330151 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lucian II 330241 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Sunburst 300170 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Hatteras Bay Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting 310155 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Surrey Climates 60 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lehr Decor 80" Bedienungsanleitung

Kichler Lighting

Kichler Lighting Canfield Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting Eads 310135 Bedienungsanleitung

Kichler Lighting

Kichler Lighting FLYY 310700MWH Bedienungsanleitung

Kichler Lighting

Kichler Lighting Botella Bedienungsanleitung

Kichler Lighting

Kichler Lighting 52 inch Colerne LED Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35157 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Grace 300316 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Eris Bedienungsanleitung

Kichler Lighting

Kichler Lighting FERRON Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung