Kichler Lighting 65" GENTRY Bedienungsanleitung
65" GENTRY
INSTRUCTION MANUAL
Product images may vary slightly from actual product.
TABLE OF CONTENTS
SAFETY RULES.......................................................................... 4
5
5
6
7
10
11
13
14
14
TOOLS REQUIRED....................................................................
PACKAGE CONTENTS.............................................................
MOUNTING OPTIONS.............................................................
HANGING THE FAN..................................................................
INSTALLATION OF SAFETY SUPPORT..........................
ELECTRICAL CONNECTIONS.............................................
FINISHING THE INSTALLATION........................................
INSTALLING THE LIGHT PLATE........................................
INSTALLING THE LED LIGHT KIT
AND GLASS SHADE ASSEMBLY......................................15
16
17
18
19
20
21
CONTROL SYSTEM SET-UP...............................................
BUTTON INSTRUCTION........................................................
INSTALLING THE WALL CONTROL
SYSTEM WALL PLATE...........................................................
OPERATION INSTRUCTIONS............................................
TROUBLESHOOTING............................................................
65" GENTRY | 3
ATTACHING THE FAN BLADES..........................................
SENSORLESS DC CONTROL PAIRING
PROCEDURES...........................................................................
22
FCC INFORMATION...............................................................
4 | KICHLER.COM
SAFETY RULES
WARNING: FOR CANADA, THIS FAN MUST BE SECURED DIRECTLY TO
THE BUILDING STRUCTURE / CEILING JOIST. DON'T SECURE THIS FAN
TO AN OUTLET BOX.
1. CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox
before starting and during the installation.
2. WARNING:
This fixture is intended for installation in accordance with the National
Electrical Code (NEC) and all local code specifications. If you are not
familiar with code requirements, installation by a certified electrician is
recommended.
3. WARNING: To reduce the risk of fire, electric shock, or personal injury, mount
to outlet box marked "acceptable for fan support of 22.7 kg (50 lbs.) or
less" and use mounting screws provided with the outlet box. Most outlet
boxes commonly used for the support of light fixtures are not acceptable for
fan support and may need to be replaced. Due to the complexity of the
installation of this fan, a qualified licensed electrician is strongly
recommended.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED
"ACCEPTABLE FOR FAN SUPPORT".
5. The outlet box and support structure must be securely mounted and capable
of reliably supporting a minimum of 50 pounds. Use only CUL Listed outlet
boxes marked "FOR FAN SUPPORT".
6. The fan must be mounted with a minimum of 7 feet clearance from the trailing
edge of the blades to the floor.
7. To operate the reverse function on this fan, press the reverse button while
the fan is running.
8. Avoid placing objects in the path of the blades.
9. To avoid personal injury or damage to the fan and other items, be cautious
when working around or cleaning the fan.
10. Do not use water or detergents when cleaning the fan or fan blades. A
dry dust cloth or lightly dampened cloth will be suitable for most cleaning.
11. After marking electrical connections, spliced conductors should be
turned upward and pushed carefully up into outlet box. The wires should be
spread apart with the grounded conductor and the equipment-grounding
conductor on one side of the outlet box.
12. Electrical diagrams are reference only. Light kits that are not packed with
the fan must be CUL Listed and marked suitable for use with the model fan
you are installing. Switches must be CUL General Use Switches. Refer to the
Instructions packaged with the light kits and switches for proper assembly.
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND
THE BLADE BRACKETS (ALSO REFERRED TO AS FLANGES) DURING
ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN THE
PATH OF THE BLADES.
TOOLS REQUIRED
Philips screw driver
Blade screw driver
11 mm wrench
Step ladder
Wire cutters
PACKAGE CONTENTS
i
j
k
f
g
h
b
c
d
e
Unpack your fan and check the
contents. You should have the
following items:
a. Fan blades (9)
b. Blade support plates (9)
c. Canopy & Ceiling mounting
bracket
d. Ball/downrod assembly
e. Coupling cover
f. Fan motor assembly
g. Light plate
h. 17W LED light kit
i. Glass shade assembly
j. Wall Transmitter
k. Part bag contents
1) Mounting hardware:
star washers (2), wire nuts (3),
machine screws (2), washers (2),
screws (2)
2) Blade attachment hardware:
screws (29)
3) Safety cable hardware:
wood screw, lock washer,
flat washer
4) Balance Kit
a
65" GENTRY | 5
6 | KICHLER.COM
MOUNTING OPTIONS
If there isn't an existing UL (cUL for Canadian Installation) listed
mounting box, then read the following instructions. Disconnect the
power by removing fuses or turning o circuit breakers.
Secure the outlet box directly to the building structure. Use appropriate
fasteners and building materials. The outlet box and its support must be
able to fully support the full weight of the fan (at least 50 lbs). Do not use
plastic outlet boxes.
Figures 1, 2 and 3 are examples of dierent ways to mount the outlet
box.
NOTE: If you are installing the ceiling fan on a sloped (vaulted) ceiling,
you may need a longer downrod to maintain proper clearance between
the tip of the blade and the ceiling. A minimum clearance of 12" is
suggested for optimal operation.
NOTE: Depending on the location you have selected for installation, you
may need to purchase and install a "Joist Hanger" for the support of the
outlet box. Make sure the joist hanger you purchase has been designed
for use with ceiling fans. (Fig. 4)
Fig. 1
Outlet box
Outlet box
Fig. 2
Provide strong
support
Recessed
outlet box Ceiling
mounting
plate
Fig. 3
ANGLED CEILING
MAXIMUM 20° ANGLE
Outlet box
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Hanger bracket
Ceiling
canopy
Canopy
cover
HANGING THE FAN
NOTE: FOR CANADA, THIS FAN MUST BE SECURED DIRECTLY TO
THE BUILDING STRUCTURE / CEILING JOIST. DON'T SECURE THIS
FAN TO AN OUTLET BOX. (SEE Fig. 6A)
REMEMBER to turn o the power before you begin.
To properly install your ceiling fan, follow the steps below.
Step 1. Remove the decorative canopy bottom cover from the canopy
by turning the cover counter clockwise. (Fig. 5)
Step 2. Remove the ceiling mounting bracket from the canopy by
removing (and save one of the two screws. Loosen the remaining screw
by a half turn. (Fig. 5)
Step 3. Pass the 120 volt supply wires from the ceiling outlet box through
the center of the ceiling mounting bracket. (Fig. 6)
Step 4. Attach the ceiling mounting bracket to the outlet box using the
screws and washers included with the outlet box. (Fig. 6)
Step 4A. Secure mounting bracket directly to a joist from the building
structure. Use only the appropriate wood screws lock washers included
with your fan. (Fig. 7) NOTE: THIS STEP IS ONLY FOR CANADA.
CAUTION! THE HANGER BRACKET MUST BE INSTALLED DIRECTLY
TO THE BUILDING JOIST USING THE TWO WOOD SCREWS AND
WASHERS PROVIDED. (Fig. 7)
65" GENTRY | 7
120V Wires
Hanger bracket
Ceiling joist
#10 Wood screws
Lock washers
120V Wires
Ceiling
hanger
bracket Mounting screws
(supplied with
electrical box)
UL Listed
electrial
box
Washers
8 | KICHLER.COM
Step 5. Remove the hanger ball from the downrod assembly by
loosening the set screw, unscrewing and removing removing the cross
pin and unscrewing the ball o the rod. (Fig. 8)
Step 6. Loosen the two set screws and remove the hitch pin and
retaining clip from the coupling on top of the motor assembly. (Fig. 9)
Step 7. Carefully feed the electrical lead wires from the fan up through
the downrod. Thread
the downrod into the coupling until the Hitch pin holes are aligned.
Next, replace the hitch pin and retaining clip. Tighten both set screws.
(Fig. 9)
HANGING THE FAN(continued)
Fig. 8
Fig. 9
Downrod
Cross pin
Hanger
ball Set screw
Supply wires
Downrod
Hitch pin
Retaining clip Set screws
Set screws
Fig. 10
Fig. 11
HANGING THE FAN(continued)
Step 8. Slip the coupling cover, canopy cover and canopy onto the
downrod. (Fig. 10)
Thread the hanger ball onto the downrod, insert the cross pin through
the downrod and tighten. Tighten the set screw.
Step 9. Lift the motor assembly into position and place the hanger ball
into the ceiling mounting bracket.
Rotate the entire assembly until the "Check Tab" has dropped into the
"Registration Slot" and seats firmly. (Fig. 11)
The entire motor assembly should not rotate (left or right) when seated
properly.
WARNING: Failure to reattach the cross pin and seat the "Check Tab"
can cause the fan to fall from the ceiling during operation. Take special
care to make sure this pin is reattached.
Registration slot
Downrod
Canopy
Canopy cover
Set screws
Hitch pin Retaining clip
Coupling cover
65" GENTRY | 9
10 | KICHLER.COM
A safety support cable is provided to help prevent the ceiling fan from
falling.
Step 1. Attach the provided wood screw and washers to the ceiling joist
next to the mounting bracket but do not tighten. (Fig. 12)
Step 2. Adjust the length of the safety cable to reach the screw and
washers by pulling the extra cable through the cable clamp until the
overall length is correct, put the end of the cable back through the cable
clamp, forming a loop at the end of the cable. Tighten the cable clamp
securely. Now, put the loop in the end of the safety cable over the wood
screw and under the washer. Tighten the wood screw securely.
NOTE: Although the safety support cable is required for Canadian
installations only. It's a good idea to make the attachment with any
installation.
Fig. 12
Ceiling mounting
bracket
Attach
safety cable
to ceiling joist
with screw and
washer
INSTALLATION OF SAFETY SUPPORT
Inhaltsverzeichnis
Sprachen:
Andere Kichler Lighting Lüfter Handbücher
Kichler Lighting
Kichler Lighting HATTERAS BAY PATIOLED 60" Bedienungsanleitung
Kichler Lighting
Kichler Lighting 300026 Bedienungsanleitung
Kichler Lighting
Kichler Lighting Deckard Bedienungsanleitung
Kichler Lighting
Kichler Lighting Imari 65 Bedienungsanleitung
Kichler Lighting
Kichler Lighting 35152 Bedienungsanleitung
Kichler Lighting
Kichler Lighting Kittery Point Bedienungsanleitung
Kichler Lighting
Kichler Lighting 300395 Bedienungsanleitung
Kichler Lighting
Kichler Lighting Industrial Fan Bedienungsanleitung
Kichler Lighting
Kichler Lighting Starkk 330180MWH Bedienungsanleitung
Kichler Lighting
Kichler Lighting Eads 310135 Bedienungsanleitung
Kichler Lighting
Kichler Lighting Almere Bedienungsanleitung
Kichler Lighting
Kichler Lighting Bronson Bedienungsanleitung
Kichler Lighting
Kichler Lighting True Bedienungsanleitung
Kichler Lighting
Kichler Lighting RIDLEY2 KLF-RIDLEY2-52-NB Bedienungsanleitung
Kichler Lighting
Kichler Lighting Canfield 300117WH Bedienungsanleitung
Kichler Lighting
Kichler Lighting POLA Bedienungsanleitung
Kichler Lighting
Kichler Lighting Decor Dorset Bedienungsanleitung
Kichler Lighting
Kichler Lighting Select Sutter Place Bedienungsanleitung
Kichler Lighting
Kichler Lighting KLF-SOLA-34-WHT-BN Bedienungsanleitung
Kichler Lighting
Kichler Lighting BASICS PRO PREMIER 330016WH Bedienungsanleitung
