Kichler Lighting Industrial Fan Bedienungsanleitung

 2*

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

Instruction Manual

Industrial Fan

A Kichler®

Select™ceiling fan

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local electrical

codes. Electrical installation should be

performed by a qualified licensed

electrician.

3. WARNING: Suitable for use with solid-

state speed controls.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting fixtures are not acceptable for fan

support and may need to be replaced,

consult a qualified electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use only CUL Listed outlet boxes

marked "FOR FAN SUPPORT".

6. The fan must be mounted with a minimum

of 10 feet clearance from the trailing edge

of the blades to the floor.

7. Avoid placing objects in the path of the

blades.

8. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

9. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

10. After marking electrical connections,

spliced conductors should be turned

upward and pushed carefully up into outlet

box. The wires should be spread apart with

the grounded conductor and the

equipment-grounding conductor on one

side of the outlet box.

11. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be CUL Listed and marked suitable

for use with the model fan you are

installing. Switches must be CUL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX

MARKED "ACCEPTABLE FOR FAN

SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR

AFTER INSTALLATION. DO NOT INSERT

OBJECTS IN THE PATH OF THE BLADES.

1. SAFETY RULES

3. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items:

a. Fan blade/bracket assemblies (3)

b. Canopy & Ceiling mounting bracket

c. Ball/downrod assembly

d. Coupling cover

e. Fan motor assembly

f. Part bag contents

1) Mounting hardware:

star washers (2), wire nuts (3),

machine screws (2), washers (2),

screws (2)

2) Blade bracket attachment hardware:

screws (8)

3) Safety cable hardware:

wood screw, lock washer, flat washer

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

Industrial Fan

4. MOUNTING OPTIONS

If there isn't an existing UL (cUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of different

ways to mount the outlet box.

NOTE: If you are installing the ceiling fan on a

sloped (vaulted) ceiling, you may need a

longer downrod to maintain proper clearance

between the tip of the blade and the ceiling. A

minimum clearance of 12" is suggested for

optimal operation.

NOTE: Depending on the location you have

selected for installation, you may need to

purchase and install a "Joist Hanger" for the

support of the outlet box. Make sure the joist

hanger you purchase has been designed for

use with ceiling fans. (Fig. 4)

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

ANGLED CEILING

MAXIMUM 30°ANGLE

Fig. 7

Fig. 8

Mounting screws

(supplied with

electrical box)

Hook

Ceiling

mounting

bracket

UL Listed

outlet box

120V Wires

Washers

Fig. 6

5. HANGING THE FAN

Supply wires

Downrod

Hitch pinRetaining clip

Set screws

Coupling

Set screws

REMEMBER to turn off the power before you

begin.

To properly install your ceiling fan, follow the

steps below.

Step 1. Remove the decorative canopy bottom

cover from the canopy by turning the cover

counterclockwise. (Fig. 5)

Step 2. Remove the ceiling mounting bracket

from the canopy by removing (and save) one

of the two screws. Loosen the remaining

screw by a half turn. (Fig. 5)

Step 3. Pass the 120 volt supply wires from

the ceiling outlet box through the center of the

ceiling mounting bracket. (Fig. 6)

Step 4. Attach the ceiling mounting bracket to

the outlet box using the screws and washers

included with the outlet box. (Fig. 6)

Step 5. Remove the hanger ball from the

downrod assembly by loosening the set screw,

removing the cross pin and sliding the ball off

the rod. (Fig.7)

Step 6. Loosen the two set screws and

remove the hitch pin and retaining clip from

the coupling on top of the motor assembly.

(Fig. 8)

Step 7. Carefully feed the electrical lead wires

from the fan up through the downrod. Thread

the downrod into the coupling until the Hitch

pin holes are aligned.

Next, replace the hitch pin and retaining clip.

Tighten both set screws. (Fig. 8)

Fig. 5

Ceiling mounting

bracket

Canopy

cover

Cross pin

Hanger ball Set screw

Downrod

Industrial Fan

Fig. 9

Fig. 10

Registration slot

Check tab

Step 8. Slip the coupling cover, canopy cover

and canopy onto the downrod.

Thread the hanger ball onto the downrod,

insert the cross pin through the downrod and

tighten. Now tighten the set screw. (Fig. 9)

Step 9. Lift the motor assembly into position

and place the hanger ball into the ceiling

mounting bracket.

Rotate the entire assembly until the "Check

Tab" has dropped into the "Registration Slot"

and seats firmly. (Fig. 10)

The entire motor assembly should not rotate

(left or right) when seated properly.

WARNING: Failure to reattach the cross pin

and seat the "Check Tab" can cause the fan to

fall from the ceiling during operation. Take

special care to make sure this pin is

reattached.

Canopy

Canopy cover

Coupling cover

Coupling

Downrod

Cross pin

Hanger ball

Fig. 11

Ceiling mounting

bracket Attach

safety cable

to ceiling joist

with screw and

washer

Fig. 12

Industrial Fan

7. ELECTRICAL CONNECTIONS

6. INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help

prevent the ceiling fan from falling.

Step 1. Attach the provided wood screw and

washers to the ceiling joist next to the mounting

bracket but do not tighten. (Fig. 11)

Step 2. Adjust the length of the safety cable to

reach the screw and washers by pulling the extra

cable through the cable clamp until the overall

length is correct, put the end of the cable back

through the cable clamp, forming a loop at the

end of the cable. Tighten the cable clamp

securely. Now, put the loop in the end of

the safety cable over the wood screw and under

the washer. Tighten the wood screw securely.

NOTE: Although the safety support cable is

required for Canadian installations only. It's a

good idea to make the attachment with any

installation.

WARNING: To avoid possible electrical shock,

be sure you have turned off the power at the

main circuit panel.

Follow the steps below to connect the fan to

your household wiring. Use the wire connecting

nuts suppled with your fan. Secure the

connectors with electrical tape. Make sure there

are no loose wire strands or connections.

A. OPTIONAL WALL CONTROL WIRING

NOTE: To wire your fan to an "OPTIONAL" wall

speed control following the steps below and

refer to Fig. 12. To wire your fan DIRECTLY to

the power supply, see the instruction on the next

page.

Step 1. Connect the fan supply (black) wire to

the black wire marked "TO MOTOR L" from the

wall switch. (Fig. 12)

Step 2. Step 2. Connect the black household

supply wire to the black wire marked "AC in L"

from the wall switch. (Fig. 12)

Finish the wall switch installation by attaching

the wall switch inside the switch box and

attaching the faceplate.

BLK BLK

GRN

Wiring

box

TO MOTOR L

AC in L

Ground to

mounting

bracket

or downrod

Power lines 120v

Green ground

Fig. 12a

Step 3. Connect the neutral fan (white) wire to

the neutral (white) household supply wire. (Fig.

12)

Step 4. Connect the fan ground wire (green)

to the household ground wire (green or bare

copper).

B. DIRECT WIRING

NOTE: Wiring connections for Figure 12a are

used when the fan is connected directly to the

main power supply by-passing any speed

switches.

In this configuration, the fan will run

continuously until power is shut off at the

breaker. this configuration is typically used for

multiple fan installations in a warehouse or

large area installation.

Connect the fan supply wire (black) to the

main supply wire (black) in the ceiling

junction box. (Fig. 12a)

Connect the fan neutral wire (white) to the

main supply neutral wire (white) in the

ceiling junction box. (Fig. 12a)

Connect the fan ground wire (green) to the

main supply ground wire (green) in the

ceiling junction box. (Fig. 12a)

Finish the installation by attaching the fan

ceiling canopy to the mounting bracket, see

next page for directions.

WARNING: TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK OR OTHER

PERSONAL INJURY, MOUNT YOUR

CEILING FAN ON A OUTLET BOX OR

SUPPORTING SYSTEM MARKED

"ACCEPTABLE FOR FAN SUPPORT".

BLK BLK

GRN

Wiring

box

Ground to

mounting

bracket

or downrod

Power lines 120v

Green ground

Step 1. Tuck all the connections neatly into the

ceiling outlet box.

Step 2. Slide the canopy up to the mounting

bracket and place one of the key hole slots

over the mounting screw on the mounting

bracket. Rotate the canopy until the screw

head locks in place at the narrow section of

the key hole. See figure 13.

Step 3. Align the remaining circular hole on the

canopy with the remaining hole on the Ceiling

Mounting Bracket. Insert and tighten the

mounting screw you removed earlier and the

mounting screw from Step 2 above. Now,

attach the canopy cover to the mounting screw

heads by inserting the screw heads into the

bottom side of the canopy cover and rotating

the cover clockwise.

NOTE: Adjust the canopy screws as

necessary until the canopy and canopy cover

are snug. (Fig. 13)

8. FINISHING THE INSTALLATION

9. ATTACHING THE FAN BLADES

Step 2. Attach each fan blade/bracket

assembly to the motor using the screws

provided. (Fig 14)

Fig. 14

Screws

Blade/bracket

assemby

Industrial Fan

Fig. 13

Outlet box

Ceiling

mounting

bracket

Canopy

Canopy cover

Screws

11. SPECIFICATIONS

1.47

'7.68

kgs 8.61

kgs

0.51

0.37

0.24

205

135

6512

4259

2223

112

140

179

RPM CFM CFM/W N.W. G.W. C.F.

120

Fan Size

56"

Speed Volts Amps Watts

High

Medium

Low

These are approximate measurements. They do not include data for any lamps or fixtures attached

to the ceiling fan.

10. TROUBLESHOOTING

Problem

Fan will not start.

Fan sounds noisy.

Fan wobble.

Solution

1. Check that all fuses or circuit breakers are installed or in the ON position.

2. Check all electrical connections to insure proper contact. CAUTION: Make

sure the main power is OFF when checking any electrical connection.

1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade brackets to the motor are

tight.

3. Make sure wire nut connections are not rubbing against each other or the

interior wall of the switch housing.

CAUTION: Make sure main power is off.

4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan

disappear during this time.

5. If using an optional light kit, make sure the screws securing the glassware

are tight. Make sure the light bulbs are not touching any other component.

6. Some fan motors are sensitive to signals from solid-state variable speed

controls. If you have installed this type of control, choose and install another

type of control.

7. Make sure the upper canopy is a short distance from the ceiling. It should not

touch the ceiling.

1. Check that all blade and blade arm screws are secure.

2. Most fan wobbling problems are caused when blade levels are unequal.

Check this level by selecting a point on the ceiling above the tip of one of the

blades. Measure this distance. Rotate the fan until the next blade is

positioned for measurement. Repeat for each blade. The distance deviation

should be equal within 1/8".

3. Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable.

4. If the blade wobble is still noticeable, interchanging two adjacent (side by

side) blades can redistribute the weight and possibly result in smoother

operation.

WARNING: TO REDUCE THE RISK OF PERSONAL INJURY AND TO INUSRE THE

PROPER OPERATION OF YOUR CEILING FAN. NEVER ATTACH THE BLADE

ASSEMBLIES UNTIL THE CEILING FAN HAS BEEN MOUNTING ON THE CEILING.

DO NOT BEND THE BLADE ARMS WHILE INSTALLING, BALANCING OR

CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN

ROTATING FAN BLADES.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting Monarch II Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting Wilton Bedienungsanleitung

Kichler Lighting

Kichler Lighting Logan Bedienungsanleitung

Kichler Lighting

Kichler Lighting Bentzen Bedienungsanleitung

Kichler Lighting

Kichler Lighting Select Sutter Place Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35156 Bedienungsanleitung

Kichler Lighting

Kichler Lighting True Bedienungsanleitung

Kichler Lighting

Kichler Lighting RIED Bedienungsanleitung

Kichler Lighting

Kichler Lighting Meredith Bedienungsanleitung

Kichler Lighting

Kichler Lighting KAPONO Bedienungsanleitung

Kichler Lighting

Kichler Lighting Canfield Bedienungsanleitung

Kichler Lighting

Kichler Lighting 54 Skye LED Bedienungsanleitung

Kichler Lighting

Kichler Lighting BISC 300710MWH Bedienungsanleitung

Kichler Lighting

Kichler Lighting Maor 310136 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Ample Bedienungsanleitung

Kichler Lighting

Kichler Lighting Universal 3 Light Fitter Bedienungsanleitung

Kichler Lighting

Kichler Lighting Starkk 330174OZ Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300395 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Riggs 300143 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Kittery Point Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300260/60-GENT Series Bedienungsanleitung

Kichler Lighting

Kichler Lighting Larissa Bedienungsanleitung

Kichler Lighting

Kichler Lighting ETL Bedienungsanleitung

Kichler Lighting

Kichler Lighting Canfield Patio 310192 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung