Kichler Lighting Bronson Bedienungsanleitung

 2*

 2*

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

Instruction Manual

Bronson

A Kichler®Select™

ceiling fan

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local electrical

codes. Electrical installation should be

performed by a qualified licensed

electrician.

3. WARNING: Suitable for use with solid-

state speed controls.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting fixtures are not acceptable for fan

support and may need to be replaced,

consult a qualified electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use only CUL Listed outlet boxes

marked "FOR FAN SUPPORT".

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the floor.

7. Do not operate reversing switch while fan

blades are in motion. Fan must be turned

off and blades stopped before reversing

blade direction.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After making the electrical connections,

spliced conductors should be turned

upward and pushed carefully up into outlet

box. The wires should be spread apart with

the ground wire and white (common) wire

to one side with the black (load) wire to the

other side of the outlet box.

12. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be CUL Listed and marked suitable

for use with the model fan you are

installing. Switches must be CUL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

OR PERSONAL INJURY, MOUNT FAN TO OUTLET

BOX MARKED "ACCEPTABLE FOR FAN

SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE BRACKETS (ALSO

REFERRED TO AS FLANGES) DURING ASSEMBLY

OR AFTER INSTALLATION. DO NOT INSERT

OBJECTS IN THE PATH OF THE BLADES.

1. SAFETY RULES

Special Notice

This appliance is equipped with a "Wattage

Limiting Device" required by the United

States Department of Energy. The device

has been installed at the factory and can not

be removed.

Installing Lamps in excess of 190 total watts

will disable the unit's light fixture. If this

should happen, you will need to reset the

lighting fixture by turning the power off to

the ceiling fan and/or light fixture,

reinstalling lamps totaling less that 190

watts and then turning the power back on.

3. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items:

a. Fan blades (4)

b. Canopy & Ceiling mounting bracket

c. Ball/downrod assembly

d. Coupling cover

e. Fan motor assembly

f. Mounting plate

g. Light kit assembly

h. Set of blade brackets (4)

i. Glass shade

j. 40W B8 candelabra bulbs (3)

k. Part bag contents

1) Mounting hardware:

wood screw, flat washer, spring washer,

star washers (2), wire nuts (3),

machine screws (2), washers (2),

screws (2)

2) Blade attachment hardware:

screws (14), washers (14),

fiber washers (14)

3) Safety cable hardware:

wood screw, lock washer, flat washer

4) Pull chains and fobs (2)

5) Balance Kit

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

BronsonTM

4. MOUNTING OPTIONS

If there isn't an existing UL (cUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of different

ways to mount the outlet box.

NOTE: If you are installing the ceiling fan on a

sloped (vaulted) ceiling, you may need a

longer downrod to maintain proper clearance

between the tip of the blade and the ceiling. A

minimum clearance of 12" is suggested for

optimal operation.

NOTE: Depending on the location you have

selected for installation, you may need to

purchase and install a "Joist Hanger" for the

support of the outlet box. Make sure the joist

hanger you purchase has been designed for

use with ceiling fans. (Fig. 4)

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

ANGLED CEILING

MAXIMUM 20°ANGLE

BronsonTM

Fig. 7

Fig. 8

Mounting screws

(supplied with

electrical box)

Hook

Ceiling

mounting

bracket

UL Listed

outlet box

120V Wires

Washers

Ceiling mounting

bracket

Canopy

Canopy cover

Downrod

Cross pin

Hanger

ball Set screw

Fig. 6

Fig. 5

5. HANGING THE FAN

Supply wires

Downrod

Hitch pin Retaining pin

Set screws

Coupling

Set screws

REMEMBER to turn off the power before you

begin.

To properly install your ceiling fan, follow the

steps below.

Step 1. Remove the decorative canopy bottom

cover from the canopy by turning the cover

counter clockwise. (Fig. 5)

Step 2. Remove the ceiling mounting bracket

from the canopy by loosening the two screws

on the bottom of the ceiling mounting bracket.

Turn the canopy counterclockwise and

remove. (Fig. 5)

Step 3. Pass the 120 volt supply wires from

the ceiling outlet box through the center of the

ceiling mounting bracket. (Fig. 6)

Step 4. Attach the ceiling mounting bracket to

the outlet box using the screws and washers

included with the outlet box. (Fig. 6)

Step 5. Remove the hanger ball from the

downrod assembly by loosening the set screw,

removing the cross pin and sliding the ball off

the rod. (Fig. 7)

Step 6. Loosen the two set screws and

remove the hitch pin and retaining clip from

the coupling on top of the motor assembly.

(Fig. 8)

Step 7. Carefully feed the electrical lead wires

from the fan up through the downrod. Thread

the downrod into the coupling until the Hitch

pin holes are aligned.

Next, replace the hitch pin and retaining clip.

Tighten both set screws. (Fig. 8)

Fig. 9

Fig. 10

Registration slot

Check tab

Step 8. Slip the coupling cover, canopy cover

and canopy onto the downrod.

Thread the hanger ball onto the downrod,

insert the cross pin through the downrod and

tighten. Now tighten the set screw. (Fig. 9)

Step 9. Lift the motor assembly into position

and place the hanger ball into the ceiling

mounting bracket.

Rotate the entire assembly until the "Check

Tab" has dropped into the "Registration Slot"

and seats firmly. (Fig. 10)

The entire motor assembly should not rotate

(left or right) when seated properly.

WARNING: Failure to properly seat the

"Check Tab" can damage the ceiling fan

during operation.

Hanger ball

Downrod

Canopy cover

Canopy

Coupling cover

Hitch pin Retaining pin

Set screwsSet screws

Fig. 11

7. ELECTRICAL CONNECTIONS

6. INSTALLATION OF SAFETY SUPPORT

(for Canadian Installation ONLY)

A safety support cable is provided to help

prevent the ceiling fan from falling, please

install it as follows.

Step 1. Attach the provided wood screw and

washers to the ceiling joist next to the

mounting bracket but do not tighten. (Fig. 11)

Step 2. Adjust the length of the safety cable to

reach the screw and washers by pulling the

extra cable through the cable clamp until the

overall length is correct, put the end of the

cable back through the cable clamp, forming a

loop at the end of the cable. Tighten the cable

clamp securely. Now, put the loop in the end of

the safety cable over the wood screw and

under the washer. Tighten the wood screw

securely.

Ceiling mounting

bracket Attach

safety cable

to ceiling joist

with screw and

washer

Fig. 12

WARNING: To avoid possible electrical shock,

be sure you have turned off the power at the

main circuit panel.

Follow the steps below to connect the fan to

your household wiring. Use the wire

connecting nuts suppled with your fan. Secure

the connectors with electrical tape. Make sure

there are no loose wire strands or

connections.

Step 1. Connect the fan supply (black) wire

and light supply (blue) wire to the black

household supply wire as shown in Figure 12.

Step 2. Connect the neutral fan (white) wire to

the neutral household (white) wire.

Step 3. Connect the fan ground wire (green) to

the household ground wire.

Step 4. After connecting the wires, spread

them apart so that the green and white wires

are on one side of the outlet box and the black

and the blue wires are on the other side.

Step 5. Turn the connecting nuts upward and

push the wiring into the outlet box.

WARNING: TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK OR OTHER

PERSONAL INJURY, MOUNT YOUR

CEILING FAN ON A OUTLET BOX OR

SUPPORTING SYSTEM MARKED

"ACCEPTABLE FOR FAN SUPPORT".

BLUE

BLK BLK

GRN

Wiring

box

Ground to

mounting

bracket

or downrod

BLUE

FAN

LIGHT

Power lines 220~240V

Green ground

REDRED

BLK

BronsonTM

Fig. 13

Step 1. Tuck all the connections neatly into the

ceiling outlet box.

Step 2. Slide the canopy up to ceiling and over

the two screws on hanger bracket. Rotate

canopy clockwise, next, while holding the

canopy with one hand, slide the canopy cover

over the screws and rotate clockwise until

tight. NOTE: Adjust the canopy screws as

necessary until the canopy and canopy cover

are snug. (Fig.13)

8. FINISHING THE INSTALLATION

Outlet box

Ceiling mounting

bracket

Canopy

Canopy cover

Screws

9. ATTACHING THE FAN BLADES

Fig. 14

CAUTION: Remove the five rubber shipping

blocks attached to the face of the motor.

These blocks keep the motor from shifting

during shipping and MUST be removed during

installation.

Step 1. Attach a blade to a blade bracket using

the screws, metal washers and fiber washers

provided. (Fig. 14)

Make sure the blade is straight when set on

the blade bracket. Tighten each mounting

screw and then repeat this procedure for each

blade.

Step 2. Attach each blade assembly to the

motor using the "Pre-Installed" mounting

screws in the blade bracket. (Fig. 14)

Screws

Washers

Set of blade brackets

blades

Screws

Fiber

washers

10. INSTALLING THE MOUNTING PLATE

Fig. 15

Fig. 16

11. INSTALLING THE LIGHT FIXTURE

1. While holding the light kit assembly under

your ceiling fan, push the square wire

connectors together. One from the fan and

one from the light fixture.

NOTE: These connectors are color coded and

will ONLY engage when the colored strips are

matched (aligned).

2. Carefully push all the wires into the switch

housing on the light kit assembly.

Attach the light kit assembly to the mounting

plate with the three screws provided. Make

use each screw is tight. (Fig. 16)

1. Loosen the two screws on the mounting ring

attached to the motor shaft and "remove" and

save the third screw. (Fig. 15)

2. Place the key holes on the mounting plate

over the 2 screws previously loosened from

the mounting ring, turn mounting plate until it

locks in place at the narrow section of the key

holes. Secure by tightening the 2 screws

previously loosened and the one previously

removed. (Fig. 15)

Mounting

plate

Mounting ring

Screws

Switch housing

Square wire connectior

Light kit

assembly

BronsonTM

Fig. 17

12. INSTALLING THE LIGHT BULBS &

GLASS SHADE

1. Install 3, 40W candelabra bulbs (included).

2. Slip the beaded pull chain into the outside

hole in the glass shade then through the hole

on the side of the decorative glass cap.

3. Fit the decorative cap onto the light kit stem.

Feed the beaded pull chain from the light kit

stem through the hold in the decorative nut

and thread the decorative nut on securely. DO

NOT OVER TIGHTEN.

4. Attache one pull chain fob to each of the

beaded pull chains. (Fig. 17)

Note: Make sure to leave enough space

between the fan pull chain and the bulbs so

the chain doesn't rub against any of the bulbs.

Decorative nut

Glass cap

Glass shade

Bulbs

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting Arkwet Weather+ Bedienungsanleitung

Kichler Lighting

Kichler Lighting Sunburst 300170 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Bead Bedienungsanleitung

Kichler Lighting

Kichler Lighting 380106 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Todo 330025 Bedienungsanleitung

Kichler Lighting

Kichler Lighting IMARI 300365SBK Bedienungsanleitung

Kichler Lighting

Kichler Lighting RIDLEY2 KLF-RIDLEY2-52-NB Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch II Bedienungsanleitung

Kichler Lighting

Kichler Lighting HATTERAS BAY PATIOLED 60" Bedienungsanleitung

Kichler Lighting

Kichler Lighting KLF-SOLA-34-WHT-BN Bedienungsanleitung

Kichler Lighting

Kichler Lighting BASICS PRO PREMIER 330016WH Bedienungsanleitung

Kichler Lighting

Kichler Lighting Terra Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting Ridley 300027OBB Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lija Bedienungsanleitung

Kichler Lighting

Kichler Lighting Golden Iridescence Bedienungsanleitung

Kichler Lighting

Kichler Lighting Szeplo II Bedienungsanleitung

Kichler Lighting

Kichler Lighting Terna 300230 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Kimberley Bedienungsanleitung

Kichler Lighting

Kichler Lighting Decor Kimberley Bedienungsanleitung

Kichler Lighting

Kichler Lighting Szeplo 370060 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Sterling Manor Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting 52" Basics Pro Bedienungsanleitung

Kichler Lighting

Kichler Lighting Vinea 52 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Humble 300415 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung