Kichler Lighting Arkwet Patio Bedienungsanleitung

  2*

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

Instruction Manual

A Kichler

Outdoor/Indoor ceiling fan

Arkwet

TM Patio

cUL Certified

for Wet Location

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local

electrical codes. Electrical installation

should be performed by a qualiﬁed

licensed electrician.

3. WARNING: Not suitable for use with

solid-state speed controls.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting ﬁxtures are not acceptable for fan

support and may need to be replaced,

consult a qualiﬁed electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use only CUL Listed outlet boxes

marked "FOR FAN SUPPORT".

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the ﬂoor.

7. Do not operate reversing switch while fan

blades are in motion. Fan must be turned

off and blades stopped before reversing

blade direction.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After marking electrical connections,

spliced conductors should be turned

upward and pushed carefully up into

outlet box. The wires should be spread

apart with the grounded conductor and

the equipment-grounding conductor on

one side of the outlet box.

12. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be CUL Listed and marked suitable

for use with the model fan you are

installing. Switches must be CUL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT

FAN TO OUTLET BOX MARKED

"ACCEPTABLE FOR FAN SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT

OBJECTS IN THE PATH OF THE BLADES.

1. SAFETY RULES

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

Unpack your fan and check the contents. You

should have the following items:

a. Fan blades (5)

b. Ceiling mounting bracket

c. Canopy

d. Ball/downrod assembly

e. Coupling cover

f. Fan motor assembly

g. Mounting plate

h. Switch housing

i. Plastic plug

j. Part bag contents

1) Mounting hardware :

wood screws (2), ﬂat washers (2),

star washers (2), wire nuts (3),

screws (2)

2) Blade attachment hardware:

screws (10),rubber washers (10)

3) Blade brackets hardware:

screws (2)

4) Safety cable hardware:

wood screw, lock washer, ﬂat washer

5) Pull chains and fobs

6) Balance Kit

3. PACKAGE CONTENTS

2. TOOLS AND MATERIALS REQUIRED

ArkwetTM Patio

4. MOUNTING OPTIONS

If there isn't an existing UL (cUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power

by removing fuses or turning off circuit

breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of different

ways to mount the outlet box.

NOTE: If you are installing the ceiling fan on a

sloped (vaulted) ceiling, you may need a

longer downrod to maintain proper clearance

between the tip of the blade and the ceiling.

A minimum clearance of 12" is suggested for

optimal operation.

NOTE: Depending on the location you have

selected for installation, you may need to

purchase and install a "Joist Hanger" for the

support of the outlet box. Make sure the joist

hanger you purchase has been designed for

use with ceiling fans. (Fig. 4)

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

ANGLED CEILING

MAXIMUM 20°ANGLE

4. MOUNTING OPTIONS

Fig. 1

Fig. 3

Fig. 4

Fig. 2

REMEMBER to turn off the power before you

begin.

To properly install your ceiling fan, follow the

steps below.

Step 1. Remove the decorative canopy

bottom cover from the canopy by turning the

cover counter clockwise. (Fig. 5)

Step 2. Remove the ceiling mounting bracket

from the canopy by removing (and save one

of the two screws. Loosen the remaining

screw by a half turn. (Fig. 5)

Step 3. Pass the 120 volt supply wires from

the ceiling outlet box through the center of the

ceiling mounting bracket. (Fig.6)

Step 4. Attach the ceiling mounting bracket to

the outlet box using the screws and washers

included with the outlet box. (Fig. 6)

Step 5. Remove the hanger ball from the

downrod assembly by loosening the set

screw, unscrewing and removing removing

the cross pin and unscrewing the ball off the

rod. (Fig.7)

Step 6. Loosen the two set screws and

remove the hitch pin and retaining clip from

the coupling on top of the motor assembly.

(Fig. 8)

Step 7. Carefully feed the electrical lead wires

from the fan up through the downrod. Thread

the downrod into the coupling until the Hitch

pin holes are aligned.

Next, replace the hitch pin and retaining clip.

Tighten both set screws. (Fig. 8)

5. HANGING THE FAN

Fig. 6

Fig. 7

Fig. 8

Mounting screws

(supplied with

electrical box)

Hook

Ceiling

mounting

bracket

CUL Listed

electrial

box

120V Wires

Washers

Downrod

Cross pin

Hanger

ball Set screw

Supply wires

Downrod

Hitch pin

Retaining clip Set screws

Set screws

Fig. 5

Hanger bracket

Ceiling

canopy

Canopy

cover

ArkwetTM Patio

Step 8. Slip the coupling cover, canopy cover

and canopy onto the downrod.

Thread the hanger ball onto the downrod,

insert the cross pin through the downrod and

tighten. Now tighten the set screw. (Fig. 9)

Step 9. Lift the motor assembly into position

and place the hanger ball into the ceiling

mounting bracket.

Rotate the entire assembly until the "Check

Tab" has dropped into the "Registration Slot"

and seats rmly. (Fig. 10)

The entire motor assembly should not rotate

(left or right) when seated properly.

WARNING: Failure to reattach the cross pin

and seat the "Check Tab" can cause the fan

to fall from the ceiling during operation. Take

special care to make sure this pin is

reattached.

Fig. 9

Fig. 10

Registration slot

Downrod

Canopy

Canopy cover

Set screws

Hitch pin Retaining clip

Coupling cover

Fig. 11

7. ELECTRICAL CONNECTIONS

6. INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help

prevent the ceiling fan from falling.

Step 1. Attach the provided wood screw and

washers to the ceiling joist next to the

mounting bracket but do not tighten. (Fig. 11)

Step 2. Adjust the length of the safety cable to

reach the screw and washers by pulling the

extra cable through the cable clamp until the

overall length is correct, put the end of the

cable back through the cable clamp, forming a

loop at the end of the cable. Tighten the cable

clamp securely. Now, put the loop in the end of

the safety cable over the wood screw and

under the washer. Tighten the wood screw

securely.

NOTE: Although the safety support cable is

required for Canadian installations only. It's a

good idea to make the attachment with any

installation.

Ceiling mounting

bracket

Attach

safety cable

to ceiling joist

with screw and

washer

Fig. 12

WARNING: To avoid possible electrical shock,

be sure you have turned off the power at the

main circuit panel.

Follow the steps below to connect the fan to

your household wiring. Use the wire connecting

nuts suppled with your fan. Secure the

connectors with electrical tape. Make sure there

are no loose wire strands or connections.

Step 1. Connect the fan supply (black) wire and

light supply (blue) wire to the black household

supply wire as shown in Figure 12.

Step 2. Connect the neutral fan (white) wire to

the neutral household (white) wire.

Step 3. Connect the fan ground wire (green) to

the household ground wire.

Step 4. After connecting the wires, spread them

apart so that the green and white wires are on

one side of the outlet box and the black wires is

on the other side.

Step 5. Turn the connecting nuts upward and

push the wiring into the outlet box.

BLK

BLUE

BLK

GRN

Wiring

box

Ground to

mounting

bracket

or downrod

Power lines 120v

Green ground

ArkwetTM Patio

8. FINISHING THE INSTALLATION

Fig. 13

Outlet box

Ceiling

mounting

bracket

Canopy

Canopy cover

Screws

Step 1. Tuck all the connections neatly into the

ceiling outlet box.

Step 2. Slide the canopy up to the mounting

bracket and place one of the key hole slots over

the mounting screw on the mounting bracket.

Rotate the canopy until the screw head locks in

place at the narrow section of the key hole.

See figure 13.

Step 3. Align the remaining circular hole on the

canopy with the remaining hole on the Ceiling

Mounting Bracket. Insert and tighten the

mounting screw you removed earlier and the

mounting screw from Step 2 above. Now,

attach the canopy cover to the mounting screw

heads by inserting the screw heads into the

bottom side of the canopy cover and rotating

the cover clockwise.

NOTE: Adjust the canopy screws as necessary

until the canopy and canopy cover are snug.

(Fig. 13)

Warning: Make sure the "Check Tab" at the

bottom of the hanger bracket is properly seated

in the "Registration Slot" on the side of the

hanger ball before attaching the canopy to the

bracket. Failure to properly seat the "Check

Tab" could damage the electrical wires when to

ceiling fan blade direction is changed while the

fan is running.

Fig. 14

Fig. 15

10. INSTALLING THE MOUNTING PLATE

1. Loosen the two screws on the mounting

ring attached to the motor shaft and "remove"

and save the third screw. (Fig. 15)

2. Place the key holes on the mounting plate

over the 2 screws previously loosened from

the mounting ring, turn mounting plate until it

locks in place at the narrow section of the key

holes. Secure by tightening the 2 screws

previously loosened and the one previously

removed. (Fig. 15)

Mounting

plate

Mounting ring

Screws

9. ATTACHING THE FAN BLADES

Insert the blade through the blade slot in the

motor housing. Align the holes in blade and

blade bracket, making sure the holes are also

aligned and secure with the screws and

rubber washers provided. Repeat process

with other blades. (Fig. 14)

Blades

Slot

Screws

Rubber washers

ArkwetTM Patio

Fig. 16

Switch housing

Mounting plate

Square wire connectors

Screws

11. INSTALLING THE SWITCH HOUSING

1. While holding the switch housing under

your ceiling fan, push the square wire

connectors together. One from the fan and

one from the switch housing. (Fig.16)

NOTE: These connectors are color coded and

will ONLY engage when the colored strips are

matched (aligned).

2. Carefully push all the wires into the switch

housing.

Attach the switch housing to the mounting

plate with the screws provided. Make sure

each screw is tight. (Fig. 16)

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting Crystal Bay Bedienungsanleitung

Kichler Lighting

Kichler Lighting VASSAR Bedienungsanleitung

Kichler Lighting

Kichler Lighting Bentzen Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lija Bedienungsanleitung

Kichler Lighting

Kichler Lighting Terra Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting Ridley 300027OBB Bedienungsanleitung

Kichler Lighting

Kichler Lighting Cortez Bedienungsanleitung

Kichler Lighting

Kichler Lighting Salvo 330045 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Sterling Manor Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting True Bedienungsanleitung

Kichler Lighting

Kichler Lighting ERIS 337060 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Larissa Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lyndon 300120 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Cameron Bedienungsanleitung

Kichler Lighting

Kichler Lighting Decor InnesII 300130 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Riggs 300143 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Tranquil Bedienungsanleitung

Kichler Lighting

Kichler Lighting Golden Iridescence Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35152 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35162 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Universal 3 Light Fitter Bedienungsanleitung

Kichler Lighting

Kichler Lighting 65" GENTRY Bedienungsanleitung

Kichler Lighting

Kichler Lighting FRYST Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35166 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung