Kichler Lighting Botella Bedienungsanleitung

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local electrical

codes. Electrical installation should be

performed by a qualified licensed

electrician.

3. WARNING: Suitable for use with solid-

state speed controls.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting fixtures are not acceptable for fan

support and may need to be replaced,

consult a qualified electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use only ETL Listed outlet boxes

marked "FOR FAN SUPPORT".

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the floor.

7. To operate the reverse function on this fan,

press the reverse button while the fan is

running.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After making the electrical connections,

spliced conductors should be turned

upward and pushed carefully up into outlet

box. The wires should be spread apart with

the ground wire and white (common) wire

to one side with the black (load) wire to the

other side of the outlet box.

12. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be ETL Listed and marked suitable

for use with the model fan you are

installing. Switches must be ETL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT

FAN TO OUTLET BOX MARKED

"ACCEPTABLE FOR FAN SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS

IN THE PATH OF THE BLADES.

1. SAFETY RULES

Special Notice

This appliance is equipped with a "Wattage

Limiting Device" required by the United

States Department of Energy. The device

has been installed at the factory and can not

be removed.

Installing Lamps in excess of 190 total watts

will disable the unit's light fixture. If this

should happen, you will need to reset the

lighting fixture by turning the power off to

the ceiling fan and/or light fixture,

reinstalling lamps totaling less that 190

watts and then turning the power back on.

3. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items:

a. Fan blades (5)

b. Blade support plates (5)

c. Canopy & Ceiling mounting bracket

d. Ball/downrod assembly

e. Decorative wire housing cover

f. Coupling cover & fan motor assembly

g. Light plate

h. Socket plate

i. Glass shade

j. 100 Watt DE - Type J halogen lamp

k. CoolTouch™ Control System

l. Part bag contents

1) Mounting hardware:

wood screws (2), flat washers (2),

star washers (2), wire nuts (3),

screws (2)

2) Blade attachment hardware:

screws (17), fiber washers (17)

3) Safety cable hardware:

wood screw, spring washer, flat washer

4) Balance Kit

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

BotellaTM

4. MOUNTING OPTIONS

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

ANGLED CEILING

MAXIMUM 20°ANGLE

If there isn't an existing ETL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of different

ways to mount the outlet box.

NOTE: If you are installing the ceiling fan on a

sloped (vaulted) ceiling, you may need a

longer downrod to maintain proper clearance

between the tip of the blade and the ceiling. A

minimum clearance of 12" is suggested for

optimal operation.

NOTE: Depending on the location you have

selected for installation, you may need to

purchase and install a "Joist Hanger" for the

support of the outlet box. Make sure the joist

hanger you purchase has been designed for

use with ceiling fans. (Fig. 4)

Fig. 8

Fig. 7

Mounting screws

(supplied with

electrical box)

Hook

Ceiling

mounting

bracket

ETL Listed

outlet box

120V Wires

Washers

Ceiling mounting

bracket

Canopy

Canopy cover

Fig. 6

Fig. 5

5. HANGING THE FAN

RMEMEBER to turn off the power before you

begin installation. This is necessary for your

safety and also the proper programing of the

control system.

To properly install your ceiling fan, follow the

steps below.

Step 1. Remove the decorative canopy bottom

cover from the canopy by turning the cover

counter clockwise. (Fig. 5)

Step 2. Remove the ceiling mounting bracket

from the canopy by removing (and save) one

of the two screws. Loosen the remaining

screw by a half turn. (Fig. 5)

Step 3. Pass the 120 volt supply wires from

the ceiling outlet box through the center of the

ceiling mounting bracket. (Fig. 6)

Step 4. Attach the ceiling mounting bracket to

the outlet box using the screws and washers

included with the outlet box. (Fig. 6)

Step 5. Remove the coupling cover from the

motor housing by removing the three screws

from the rim of coupling cover. (Fig. 7)

Step 6. Remove the hanger ball from the

downrod assembly by loosening the set screw,

removing the cross pin and sliding the ball off

the rod. (Fig. 8)

SPECIAL NOTE: For proper Control System

Programing, it is essential that power is NOT

connected or turned on to the ceiling fan

during the installation process.

You will be instructed at the proper time to

power up the system.

Collar

Coupling cover

Screws

Cross pin

Hanger ball

Set screw

Downrod

BotellaTM

Fig. 9

Fig. 11

Fig. 10

Registration slot

Check tab

Step 7. Loosen the two set screws and

remove the hitch pin and retaining clip from

the coupling on top of the motor assembly.

(Fig. 9)

Step 8. Carefully feed the electrical lead wires

from the fan up through the downrod. Thread

the downrod into the coupling until the Hitch

pin holes are aligned.

Next, replace the hitch pin and retaining clip.

Tighten both set screws. (Fig. 9)

Step 9. Slip the coupling cover, decorative

wire housing cover, canopy cover and canopy

onto the downrod. Secure the coupling cover

to the motor housing using the three screws

previously removed. (Fig. 10)

Step 10. Attach the decorative wire housing

cover to the top of the motor housing using the

four screws provided. (Fig. 10)

Thread the hanger ball onto the downrod,

insert the cross pin through the downrod and

tighten. Now tighten the set screw. (Fig. 10)

Step 11. Lift the motor assembly into position

and place the hanger ball into the ceiling

mounting bracket.

Rotate the entire assembly until the "Check

Tab" has dropped into the "Registration Slot"

and seats firmly. (Fig. 11)

The entire motor assembly should not rotate

(left or right) when seated properly.

WARNING: Failure to reattach the cross pin

and seat the "Check Tab" can cause the fan to

fall from the ceiling during operation. Take

special care to make sure this pin is

reattached.

Downrod

Canopy

Canopy cover

Decorative

wire housing

cover

Coupling

cover

Screws

Supply wires

Downrod

Hitch pin

Retaining clip

Set screws

Coupling

Set screws

Cross pin

Hanger ball

Set screw

Fig. 12

Ceiling mounting

bracket Attach

safety cable

to ceiling joist

with screw and

washer

Fig. 13

7. ELECTRICAL CONNECTIONS

6. INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help

prevent the ceiling fan from falling, please

install it as follows.

Step 1. Attach the provided wood screw and

washers to the ceiling joist next to the

mounting bracket but do not tighten. (Fig. 12)

Step 2. Adjust the length of the safety cable to

reach the screw and washers by pulling the

extra cable through the cable clamp until the

overall length is correct, put the end of the

cable back through the cable clamp, forming a

loop at the end of the cable. Tighten the cable

clamp securely. Now, put the loop in the end of

the safety cable over the wood screw and

under the washer. Tighten the wood screw

securely.

NOTE: Although the safety support cable is

required for Canadian installations only. It's a

good idea to make the attachment with any

installation.

WARNING: To avoid possible electrical shock,

be sure you have turned off the power at the

main circuit panel.

Follow the steps below to connect the fan to

your household wiring. Use the wire connecting

nuts suppled with your fan. Secure the

connectors with electrical tape. Make sure there

are no loose wire strands or connections.

Step 1. Connect the fan supply (black) wire to

the black household supply wire as shown in

Figure 13.

Step 2. Connect the neutral fan (white) wire to

the neutral household (white) wire.

Step 3. Connect the fan ground wire (green) to

the household ground wire.

Step 4. After connecting the wires, spread them

apart so that the green and white wires are on

one side of the outlet box and the black and

blue wires are on the other side.

Step 5. Turn the connecting nuts upward and

push the wiring into the outlet box.

White (neutral)

Green or bare

copper (ground)

White ("AC IN N")

Ground (green)

(Connect to ground wire

on hanger bracket if no

house ground wire exists.)

Outlet box

Black ("AC IN L")

Black (motor)

BotellaTM

Step 1. Tuck all the connections neatly into

the ceiling outlet box.

Step 2. Slide the canopy up to the mounting

bracket and place one of the key hole slots

over the mounting screw on the mounting

bracket. Rotate the canopy until the screw

head locks in place at the narrow section of

the key hole. See figure 14.

Step 3. Align the remaining circular hole on

the canopy with the remaining hole on the

Ceiling Mounting Bracket. Insert and tighten

the mounting screw you removed earlier and

the mounting screw from Step 2 above. Now,

attach the canopy cover to the mounting screw

heads by inserting the screw heads into the

bottom side of the canopy cover and rotating

the cover clockwise.

NOTE: Adjust the canopy screws as

necessary until the canopy and canopy cover

are snug. (Fig. 14)

Warning: Make sure the "Check Tab" at the

bottom of the hanger bracket is properly

seated in the "Registration Slot" on the side of

the hanger ball before attaching the canopy to

the bracket. Failure to properly seat the

"Check Tab" could damage the electrical wires

when to ceiling fan blade direction is changed

while the fan is running.

8. FINISHING THE INSTALLATION

9. ATTACHING THE FAN BLADES

Step 1. Insert the blade through the blade slot

in the motor housing. Align the holes in

blade and blade bracket, place the blade

support plate on blade as showing in Figure

15, making sure the holes are also aligned and

secure with screws and fiber washers

provided.

Step 2. Repeat process with other blades.

Fig. 14

Fig. 15

Outlet box

Ceiling

mounting

bracket

Canopy

Canopy cover

Screws

Blades

Blade

support

plates

Screws

Fiber washers

Fig. 16

Fig. 17

Light plate

Screws

Mounting ring

Socket plate

Screws

Light plate

Wire connectors

BotellaTM

10. INSTALLING THE LIGHT PLATE

Step 1. Loosen the two screws on the

mounting ring attached to the motor shaft and

"remove" and save the third screw. (Fig. 16)

Step 2. Place the key hole slots on the light

plate over the two screws previously loosened

on the mounting ring.

Turn the light plate until is locks in place at the

narrow section of the key hole slots.

Tighten both key hole screws and replace the

third screw previously removed and tighten

securely.

11. INSTALLING THE SOCKET PLATE

NOTE: Before continuing installation, confirm

that the power is still turned off at the main

circuit breaker or by removing the correct fuse.

Turning the power off using a wall switch is not

sufficient to prevent electrical shock.

Step 1. Loosen the two mounting screws on

the inside of the light plate then remove and

save the third screw.

Step 2. Hold the Lamp Socket Plate close to

the light plate and connect the white wires

from the socket plate and the fan by pushing

the connectors together. Follow the same

procedure with the black wires. (Fig. 17)

Step 3. Tuck the connections neatly into the

light plate. Place the key holes on the socket

plate over the 2 screws previously loosened

from the light plate, turn the socket plate until it

locks in place at the narrow section of the key

holes. Secure by tightening all three screws.

(Fig. 17)

Fig. 18

Step 1. Install the 100 Watt DE - Type J

halogen lamp (provided). (Fig. 18)

Step 2. Raise the glass shade against the

mounting plate and turn clockwise until snug,

DO NOT OVERTIGHTEN. (Fig. 18)

12. INSTALLING THE LAMP AND

GLASS SHADE

Lamp

Mounting plate

Glass shade

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting RIDLEY2 KLF-RIDLEY2-52-NB Bedienungsanleitung

Kichler Lighting

Kichler Lighting Saxon Premier Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35162 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35155 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Hatteras Bay Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting 54 Skye LED Bedienungsanleitung

Kichler Lighting

Kichler Lighting Kittery Point Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch II Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting True Bedienungsanleitung

Kichler Lighting

Kichler Lighting Imari 65 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Bellamy Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch Bedienungsanleitung

Kichler Lighting

Kichler Lighting Select Dorset Bedienungsanleitung

Kichler Lighting

Kichler Lighting ELLYS Bedienungsanleitung

Kichler Lighting

Kichler Lighting Golden Iridescence Bedienungsanleitung

Kichler Lighting

Kichler Lighting Canfield Patio 310192 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Sterling Manor Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting FLYY 310700MWH Bedienungsanleitung

Kichler Lighting

Kichler Lighting Golden Iridescence Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lucian II 330241 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Select Canfield 300107 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Salvo 330045 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300395 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Harbour Walk Patio Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung