Kichler Lighting 54 Skye LED Bedienungsanleitung

54" Skye LED

TABLE OF CONTENTS

SAFETY RULES ………………………………………………………. 4

TOOLS AND MATERIAL REQUIRED ………………… 5

PACKAGE CONTENTS …………………………………………. 5

MOUNTING OPTIONS ………………………………………… 6

HANGING THE FAN ………………………………………....... 7

INSTALLATION OF SAFETY SUPPORT ……………… 9

ELECTRIC CONNECTIONS ………………………………… 10

FINISHING THE INSTALLATION ……………………….. 11

ATTACHING THE FAN BLADES ………………………… 12

INSTALLING THE MOUNTING PLATE ……………… 13

54" Skye LED

TM 3

INSTALLING THE LIGHT KIT ………………………………… 14

INSTALLING THE LAMP AND GLASS SHADE …… 15

INSTALLING THE TRANSMITTER………………………… 15

CONTROL SYSTEM SET-UP ………………………………… 16

OPERATING INSTRUCTIONS ……………………………… 17

TROUBLESHOOTING………………………………………………18

FCC WARNING…………………………………………………………..19

1. To reduce the risk of electric shock, insure electricity has

been turned o at the circuit breaker or fuse box before

beginning.

2. All wiring must be in accordance with the National

Electrical Code and local electrical codes. Electrical

installation should be performed by a qualified licensed

electrician.

3. WARNING: Suitable for use with solid-state speed

controls.

4. WARNING: To reduce the risk of personal injury, use

only the two steel screws (and lock washers) provided

with the outlet box for mounting to the outlet box. Most

outlet boxes commonly used for the support of lighting

fixtures are not acceptable for fan support and may

need to be replaced,consult a qualified electrician if in

doubt.

5. To operate the reverse function on this fan, press the

reverse button while the fan is running.

6. Avoid placing objects in the path of the blades.

7. To avoid personal injury or damage to the fan and other

items, be cautious when working around or cleaning the

fan.

8. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be suitable

for most cleaning.

9. After making the electrical connections, spliced conductors

should be turned upward and pushed carefully up intooutlet box.

The wires should be spread apart with the ground wire and white

(common) wire to one side with the black (load) wire to the other

side of the outlet box.

10. Electrical diagrams are reference only.Light kits that are not

packed with the fan must be ETL Listed and marked suitable

for use with the model fan you are installing. Switches must

be ETL General Use Switches. Refer to the Instructions

packaged with the light kits and switches for proper assembly.

SAFETY RULES

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS IN THE PATH OF THE BLADES.

PACKAGE CONTENTS

Unpack your fan and check the contents . You should have the following items:

A. Mounting bracket

B. Ball / downrod assembly (1)

C. Canopy

D. Canopy Hole Cover

E. Coupling cover

F. Motor Body

G. Set of 5 blades arm and

pre-installed mounting screws

H. Fan Blades (5)

I. Switch Housing

J. Light Kit

K. Fan Lamp (Upper light 2*5W

/ Bottom light 2*5W)

L. Glass Shade

M. Finial

N. Wall Mount Control System

O. Package hardware

Wood screws(2) , flat washers (2) ,

1) Mounting hardware :

2) Blade attachment hardware :

3) Blade arm hardware : screw (2)

4) Safety cable hardware :

7) Screw hardware: screw (3)

screws (2) , lock washers (2),

wire nuts (3)

Screws (17) , fiber washers (17)

Wood screw (1) , spring washer (1),

flat washer (1)

Finial nut (1)

5) Balance kit

6) Finial nut hardware:

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

TOOLS REQUIRED

54" Skye LED

TM 5

MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect the

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box and its

support must be able to fully support the moving weight of the fan

(at least 50 lbs). Do not use plastic outlet boxes.

box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A minimum

clearance of 12” is suggested for optimal operation.

NOTE: Depending on the location you have selected for installation,

you may need to purchase and install a “Joist Hanger” for the

support of the outlet box. Make sure the joist hanger you purchase

has been designed for use with ceiling fans. (Fig. 4)

Fig. 1

Outlet box

Fig. 2

Provide strong

support

Recessed

outlet box Ceiling

mounting

plane

Fig. 3

ANGLED CEILING

MAXIMUM 20° ANGLE

Outlet box

Fig. 4

54" Skye LED

TM 7

HANGING THE FAN

REMEMBER to turn o the power before you begin installation. This is necessary

for your safety and also the proper programming of the control system.To properly

install your ceiling fan, follow the steps below.

Step 1 . Before attaching fan to outlet box (not included), ensure the outlet box is

securely fastened to at least two points to a structural ceiling member (a loose box

will cause the fan to wobble). Pass the 120 volt supply wires from the ceiling outlet

box through the center of the ceiling mounting bracket. Install mounting bracket to

outlet box in ceiling using the screws and washers included with the outlet box or

screws and washers in the hardware bag. (Fig. 5)

Step 2. Remove the hanger ball from downrod assembly by loosening set screws ,

removing the cross pin, and sliding ball o the rod.( Fig. 6)

Fig. 5

Flat Washer

Screw

Ceiling Mounting Bracket

Outlet Box

Fig. 6

Downrod

Cross Pin Set Screw

Hanger Ball

Step 5

WARNING:

. Now lift the motor body into position and place the hanger ball into the hanger

bracket. Rotate until the "Check Tab" has dropped into the "Registration Slot " and

seats ﬁrmly. ( Fig. 9) The entire motor body should not rotate if this is done correctly.

Failure to properly seat the "Check Tab" can damage the ceiling fan during

operation.

Fig. 9

Check Tab Registration Slot

Step 4. Slip the coupling cover, canopy hole cover and canopy onto the downrod.

Carefully reinstall the hanger ball onto the downrod . Make sure the cross pin is in the

correct position and the set screw is tight and the wires are not twisted . ( Fig. 8)

Step 3. Loosen the two set screws and remove the lock pin and hitch pin from the top

coupling of the motor body.Carefully feed the fan wires up through the downrod.

Thread the downrod onto the motor coupling until the hitch pin holes are aligned.

Next, replace the lock pin and hitch , pinand tighten both set screws. (Fig. 7)

Fig. 7

Hitch Pin

Lock Pin

Set Screw

Motor Body

Hitch Pin

Lock Pin

Set Screw

Fig. 8

Motor Body

Hanger Ball

Canopy

Canopy Hole

Cover

Coupling Cover

54" Skye LED

TM 9

Step 1.

NOTE:

INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan from faIling, please

install it as follows.

Drive a wood screw and washers into the side of the brace that holds the outlet

box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig. 10)

Insert the safety cable through the mounting bracket and one of the holes in the

outlet box into the ceiling. Adjust the length of the safety cable to reach the screw and

washers by pulling the extra cable through the cable clamp until the overall length is

correct, put the end of the cable back through the cable clamp, forming a loop at the

end of the cable. Tighten the cable clamp securely. Now, put the loop in the end of the

safety cable over the wood screw and under the washer. Tighten the wood screw

securely. (Fig. 11)

Although the safety support cable is required for Canadian installations only.

It’s a good idea to make the attachment with any installation.

Step 2.

Fig. 10

Flat Washer

Wood Screw

Spring Washer

Outlet Box

Support Brace

Ceiling

Fig. 11

Safety Cable Bolt

Wood Screw

MAKE THE ELECTRIC CONNECTIONS

WARNING: To avoid possible electrical shock,be sure you have turned o the power at

the main circuit panel before wiring. Follow the steps below to connect the fan to your

household wiring. Use the wire connecting nuts supplied with your fan. Secure the

connector with electrical tape. Make sure there are no loose wire stands or connections.

WARNING: If your house wires are dierent colors than referenced in this manual, stop

immediately. A professional electrician is recommended to determine properwiring.

NOTE: The wall mount control system is equipped with 16 code combinations to prevent

possible interference from or to other remote units. The frequency switches on your

receiver and transmitter have been preset at the factory. Please recheck to make sure

the switches on the transmitter and receiver are set to the same position, any

combination of settings will operate the fan as long as the transmitter and receiver are

set to the same opposition. ( Fig. 12 )Changing the order of switches on each switch

block, changes the operational frequency.

Step 1. Insert the receiver into the mounting bracket, and keep flat in opposition of

ceiling. (Fig. 13)

Step 2. Motor to Receiver Electrical Connections: Connect the BLACK wire from the

fan to BLACK wire marked "TO MOTOT L" from the receiver. Connect the WHITE

wire from the fan to the WHITE wire marked "TO MOTOR N" from the receiver.

Connect the BLUE wire from the fan to the BLUE wire marked "FOR BOTTOM

LIGHT " from the receiver. Connect the ORANGE wire from the fan to the ORANGE

wire marked "FOR UPPER LIGHT " from the receiver. Secure all the wire connections

with the plastic wire nuts provided. ( Fig. 14)

Fig. 13

Mounting Bracket

Receiver

Fig. 14

White (Neutral)

Blue(FOR BOTTOM LIGHT) Ground wire

White("AC IN N")

White("TO MOTOR N")

Green or bare copper (ground)

Black (motor)

Black ("TO MOTOR L")

Receiver

Black("AC" IN L")

Black (hot)

Outlex box

White (Neutral)

Blue(FOR BOTTOM LIGHT)

Orange (FOR UPPER LIGHT)

Fig. 12

Code Switch

ON ECE

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting Wilton Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35152 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lehr Decor 80" Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lucia Bedienungsanleitung

Kichler Lighting

Kichler Lighting 380106 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300260/60-GENT Series Bedienungsanleitung

Kichler Lighting

Kichler Lighting RIED Bedienungsanleitung

Kichler Lighting

Kichler Lighting Starkk Bedienungsanleitung

Kichler Lighting

Kichler Lighting Bellamy Bedienungsanleitung

Kichler Lighting

Kichler Lighting Decor InnesII 300130 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Motu Bedienungsanleitung

Kichler Lighting

Kichler Lighting 310155 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch II Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting RIDLEY2 KLF-RIDLEY2-52-NB Bedienungsanleitung

Kichler Lighting

Kichler Lighting BISC 300710MWH Bedienungsanleitung

Kichler Lighting

Kichler Lighting Humble 300415 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Deckard Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch II Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch Bedienungsanleitung

Kichler Lighting

Kichler Lighting Eads 310135 Bedienungsanleitung

Kichler Lighting

Kichler Lighting HATTERAS BAY PATIOLED 60" Bedienungsanleitung

Kichler Lighting

Kichler Lighting VASSAR Bedienungsanleitung

Kichler Lighting

Kichler Lighting 330013 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Ried 300356 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung