Kichler Lighting Golden Iridescence Bedienungsanleitung

Golden IridescenceTM

Includes our new

CoolTouchTM Control System

Looks permanent, but goes wherever you go!

U.S. Patent Pending

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

A Kichler®Décor™ceiling fan

Designed to coordinate with a popular Kichler Lighting collection.

Instruction Manual

KHA9090101

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

3. WARNING: To reduce the risk of electrical

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the floor.

7. To operate the reverse function on this fan,

press the reverse button while the fan is

running.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After marking electrical connections,

spliced conductors should be turned

upward and pushed carefully up into outlet

box. The wires should be spread apart with

12. Electrical diagrams are for reference only.

Light kits that are not packed with the fan

must be marked suitable for use with the

Instructions packaged with the light kits and

switches for proper assembly.

1. SAFETY RULES

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT FAN TO

OUTLET BOX MARKED "ACCEPTABLE FOR FAN

WARNING

All wiring must be in accordance with the

National Electrical Code, ANSI/NFPA70-1999

and local electrical codes. Electrical installa-

tion should be performed by a qualified

licensed electrician.

WARNING: To reduce the risk of fire,

electric shock, or personal injury, mount

this fan to outlet box marked "Acceptable

for Fan Support" and use mounting

screws provided with the outlet box. Most

outlet boxes commonly used for the sup-

port of light fixtures are not acceptable for

fan support and may need to be replaced.

Due to the complexity of the installation of

this fan, a qualified licensed electrician is

strongly recommended.

conductor of a fan identified as grounded

condutor to be connected to a grounded

conductor of power supply, conductor of fan

identified as ungrounded conductor to be

connected to an ungrounded conductor of

power supply,conductor of fan identified for

equipment grounding to be connected to an

equipment-grounding conductor.

breaker or fuse box before cleaning and

shock and fire, do not use this fan with

any solid-state fan speed control device.

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE BRACKETS WHEN

INSTALLING THE BRACKETS, BALANCING THE

BLADES, OR CLEANING THE FAN. DO NOT

INSERT FOREIGN OBJECTS IN BETWEEN ROTAT-

ING FAN BLADES.

SUPPORT."

pounds. Use the outlet boxes marked

"FOR FAN SUPPORT."

model fan you are installing. Refer to the

maintenace, or attempting installation.

3. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items:

Philips screw driver

Slot screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

Golden IridescenceTM

a. Fan blades (5)

b. Mounting bracket(1)

c. Canopy (1)

d. Canopy Cover (1)

e. Ball/downrod assembly (1)

& extra downrod (1)

f. Coupling cover (1)

g. Fan assembly (1)

h. Set of blade brackets (5)

i. Mounting plate (1)

j. Upper glass bowl (1)

k. Light plate ASM (1)

l. Bulb (4)

m. Receiver +7 wire nuts

n. CoolTouch™ Control System

o. Parts Bag Contents

1) Mounting hardware:

a. wood screws (2), flat washers (2),

screws (2),wire nuts (4)

2) Blade attachment hardware:

a. screws (16), flat washers (16),

fiber washers (16)

3) Blade bracket hardware:

a. screws (1)

4) Safety cable hardware:

a. wood screw (1), spring washer (1),

flat washer (1)

5) Mounting plate for glass hardware:

a. mounting plates for upper glass (3),

manual nuts (3)

6) Balance kit

4. MOUNTING OPTIONS

Figures 1,2 and 3 are examples of different

ways to mount the outlet box.

NOTE: You may need a longer downrod to

maintain proper blade clearance when

installing on a steep, sloped ceiling. (Fig. 3)

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

If there isn't an exsiting UL (CUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need a

joist hanging bracket as shown in Fig. 4.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and build-

ing materials. The outlet box and its support

must be able to fully support the moving weight

of the fan (at least 50 lbs). Do not use plastic

outlet boxes.

Golden IridescenceTM

5. HANGING THE FAN

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly:

Step 2. Secure the mounting bracket to the

ceiling outlet box using screws and washers

provided with the outlet box. (Fig. 6)

Step 4. Loosen the two set screws and

remove the hitch pin and lock pin from the top

coupling of the motor assembly. (Fig. 8)

Step 1. Remove the fan motor and housing

assembly from the protective plastic bag

and take the lower styrofoam packing pad

out of the carton. Place the styrofoam pad

on the floor. Then place the fan assembly

into the styrofoam pad with the bottom of the

motor facing up.(The lower foam pad serves

as a holder for the fan during the first stages

of assembly). Remove the plastic motor

shipping block and discard. (Fig. 5)

Step 5. Carefully feed fan electrical wires up

through the downrod. Thread the downrod

onto the motor coupling until the hitch pin

holes are aligned. Next, replace hitch pin and

lock pin, and tighten both set screws.(Fig. 8)

Step 3. Use a screwdriver to loosen the cross

pin and remove it from downrod assembly.

Loosen the set screw and rotate the hanger

ball off the downrod. (Fig. 7)

Fan housing

Screw

shipping block

Fig. 7

Fig. 5

Fig. 6

Fig. 8

CUL listed

electrial box

Mounting bracket

Mounting screw 120V wires

Washer

Hitch pin

Set screw

Lock pin

Downrod

Hanger Ball

Cross Pin

Set Screw

Fig. 10

Fig. 9

Fig. 11

Registration slot

Step 6. Slip coupling cover, canopy cover and

canopy onto the downrod. Carefully reinstall

the hanger ball onto the dowrod. Make sure

set screw on hanger ball is tight. (Fig. 9)

Step 8. Now lift motor assembly into position

Rotate motor assembly until the “check

groove” has dropped into the “registration

slot” and seats firmly. (Fig. 11)

Step 7. Carefully pass the upper glass bowl

over the downrod and let it rest on top of the

motor housing. (Fig. 10) Align the slot on the

mounting plate with the screw stem on the

motor housing. Set the mounting plate so the

screw stem comes through slot on the mounting

plate with the bottom curled end of the mount-

ing plate resting against the side of the glass

bowl. Tighten the manual nut provided. Repeat

this process for the remaining two mounting

plates. Install four (4) lamps 15W (included),

one in each sochet.

NOTE: The entire motor assembly should not

rotate if this is done correctly.

NOTE: Please make sure all set screws are in

place and tight before installation the following

steps.

Canopy

Coupling cover

Downrod Canopy cover

Glass bowl

Manual nut

Mounting plate

the cross pin is in the correct position and the

and place hanger ball into the hanger bracket.

Golden IridescenceTM

6. INSTALLATION OF SAFETY SUPPORT

( For Canadian Installation ONLY )

Fig. 12-2

Fig. 12-1

Fig. 13

Fig. 14

7. MAKE THE ELECTRIC CONNECTIONS

Code switch

Receiver

Hanger

bracket

Battery Compartment

A safety support cable is provided to help prevent

the ceiling fan from failing, please install it as

follows.

Step 1. Attach the provided wood screw and

washers to the ceiling joist next to the mounting

bracket but do not tighten. (Fig. 12-1)

Step 2. Adjust the length of the safety cable to

reach the screw and washers by pulling the extra

cable through the cable clamp until the overall

length is correct, put the end of the cable back

through the cable clamp, forming a loop at the

end of the cable. Tighten the cable clamp

securely. Now, put the loop in the end of the

safety cable over the wood screw and under the

washer. Tighten the wood screw securely. See

Fig. 12-2

WARNING: To avoid possible electrical shock,

be sure the electricity is turned off at the main

circuit breaker or fuse box before wiring.

WARNING: If your house wires are different

colors than referenced in this manual, stop

immediately. A professional electrician is recom-

mended to determine proper wiring.

NOTE: The CoolTouch™ Control System is

equipped with 16 code combinations to prevent

possible interference from or to other remote

units. The frequency switches on your receiver

and transmitter have been preset at the factory.

Please recheck to make sure the switches on

the transmitter and receiver are set to the same

position, any combination of setting will operate

the fan as long as each switch on the transmitter

and receiver are set to the same opposition.

(Fig. 13) Changing the order of switches on

each switch block, changes the operational

frequency.

Step 1. Insert the receiver into the mounting

bracket, with the flat toward the ceiling. (Fig. 14)

Step 2. Motor to Receiver Electrical Connec-

tions:

NOTE: Make all of the following connections

with “Wire Nut” connectors.

Connect the black wire from the fan to black

wire marded “TO MOTOR L” from the receiver.

Connect the white wire from the fan to the white

wire marked “TO MOTOR N” from the receiver.

Connect the blue wire from the fan to the blue

wire marked “FOR BOTTOM LIGHT” from the

receiver. Connect the orange wire from fan to

the orange wire marked “FOR UPPER LIGHT”

receiver. Secure all the wire connections with

the plastic wire nut provided. (Fig. 15 on the

next page)

Ceiling

Support Brace

Outlet Box

Wood Screw

Flat Washer

Spring Washer

Wood Screw

Safety Cable bolt

Fig. 15

Fig. 16

8. INSTALLING THE CEILING CANOPY

Step 2. Slide the canopy up to ceiling fan and

onto the two screws on hanger bracket.

Rotate the canopy clockwise and tighten the

two screws. Next, while holding the canopy

with one hand, slide the canopy cover over the

screws and rotate clockwise until tight.

Step 3. Receiver to House Supply Wires

Electrical Connections: Connect the black

(hot) wire from the ceiling to the black wire

marked "AC in L" from the receiver. Connect

the white(neutral) wire from the ceiling to the

white wire marked "AC in N" from the Receiver.

Secure the wire connections with the plastic

wire nuts provided. (Fig. 15)

Step 4. If your outlet box has a ground wire

(green or bare copper) connect it to the fan

ground wiresSecure the wire connection with

a plastic nut provided.

NOTE: Carefully tuck the wire connections up

into the outlet box. (Fig. 15)

Warning: One last time, make sure the “Check

Tab” at the bottom of the hanger bracket is

properly seated in the “Registration Slot” on the

side of the hanger ball before attaching the

canopy to the bracket. Failure to properly seat

the “Check Tab” could damage the electrical

wires when to ceiling fan blade direction is

changed while the fan is running.

NOTE: The transmitting unit must be installed

at a maximum distance of 30 feet from the

ceiling fan for proper signal transmission

between the transmitting unit and the fan's

receiving unit.

Step 1. Make sure all of the electrical connec-

tions are tucked neatly into ceiling outlet box.

NOTE: You may need to adjust the canopy

mounting screws as necessary until the

canopy and canopy cover are have a snug fit.

(Fig.16)

white (neutral)

Ground Wire

White("AC IN N")

Copper (ground)

White("to motor N")

Green or bare

White (neutral)

Black (motor)

Orange

(For upper light)

Blue (for bottom light)

Black ("to motor L")

Receiver

Black("AC" IN L")

Black (hot)

Outlex box

Canopy cover

Orange

Blue

Outlet box

Hanger bracket

Screw

Canopy

Canopy cover

Golden IridescenceTM

9. ASSEMBLYING AND ATTACHING

THE FAN BLADES

Fig. 17

Fig. 19

Fig. 18

10. INSTALLATING THE MOUNTING PLATE

Step 2. Make sure the blade is straight and

tighten each screw until the fiber washer is

slightly compressed and all three screws are

secure.

Step 3. Attach each completed blade assem-

mounting screws in each blade bracket. (Fig.

18) Make sure each mounting screw is

Step 1. Attach the blade to the blade

bracket using the screws, washers and

fiber washers provided. Refer to Fig. 17 as

needed. Start each screw into the bracket.

Repeat for the two (2) remaining screws.

1. Remove 1 of the 3 screws on the mount-

ing ring and loosen the other 2 screws. Do

2. Place the key holes on the mounting

plate over the 2 screws previously loos-

ened and turn the mounting plate until it

locks in place at the narrow section of the

key holes. Secure by tightening the 2

screws previously loosened and reinstall

the one removed. (Fig. 19)

Blade

Screws

Blade

Blade bracket

Mounting plate

Screw

Mounting ring

Screw

Metal washer

Fiber washer

比例

1.000

Blade bracket

not remove the mounting ring located on

the motor shaft.

securely tightened.

bly to the face of the motor using the “pre-installed”

Fig. 21

Fig. 20

11. INSTALLING THE LIGHT PLATE

NOTE: Before continuing, make sure the power

is disconnected by turning off the circuit breaker

Step 1. Loosen the 3 screws from the mounting

plate.

Step 2. The square plastic wiring connectors

will only fit together one way. Match up the color

on the side of each connector, then push them

together until the snap engages. (Fig. 20)

Step 3. Tuck the new connections neatly into

light plate assembly, place the light plate key

holes over the 3 screws previously loosened on

the mounting plate, turn light plate until it locks

in place at the narrow section of the key holes.

Secure by tightening the 3 screws previously

loosened. (Fig. 21)

YOUR NEW KICHLER CEILING FAN IS NOW

REDAY TO USE. REMEMBER TO RESTORE

ALL POWER.

connector

Light Plate Assembly

or removing the fuse at the circuit box.

from the ceiling fan and the switch housing

Switch Housing

Andere Handbücher für Golden Iridescence

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting 35166 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Meredith Bedienungsanleitung

Kichler Lighting

Kichler Lighting BASICS PRO SELECT 330017MWH Bedienungsanleitung

Kichler Lighting

Kichler Lighting KOSMUS Bedienungsanleitung

Kichler Lighting

Kichler Lighting Sterling Manor Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch Bedienungsanleitung

Kichler Lighting

Kichler Lighting Deckard Bedienungsanleitung

Kichler Lighting

Kichler Lighting Cadence Bedienungsanleitung

Kichler Lighting

Kichler Lighting Salvo 330045 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Ample Bedienungsanleitung

Kichler Lighting

Kichler Lighting BISC 300710MWH Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300044 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Starkk 330174OZ Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lyndon 300120 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Kittery Point Bedienungsanleitung

Kichler Lighting

Kichler Lighting Select Sutter Place Bedienungsanleitung

Kichler Lighting

Kichler Lighting Ried 300356 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Selectlight fixture Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch II Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lacey Bedienungsanleitung

Kichler Lighting

Kichler Lighting Decor Dorset Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lija 330140NI Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lehr Decor 80" Bedienungsanleitung

Kichler Lighting

Kichler Lighting Seaside 310181WZC Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung