Kichler Lighting Sola 330151 Bedienungsanleitung

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

Instruction Manual

Sola

A Kichler

Select ceiling fan

™

330150, 330151, 330152

3066708

Includes wall mount control system

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local

electrical codes. Electrical installation

should be performed by a qualiﬁed

licensed electrician.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting ﬁxtures are not acceptable for fan

support and may need to be replaced,

consult a qualiﬁed electrician if in doubt.

5. WARNING: To reduce the risk of ﬁre, electric

shock, or Personal Injury, mount directly to a

structural framing member or to an outlet box

marked 'Acceptable for Fan Support of

15.9 kg (35 lbs) or less'. For outlet box

mounting, use mounting screws provided with

the outlet box.

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the ﬂoor.

7. To operate the reverse function on this

fan, press the reverse button while the fan

is running. A few seconds later the fan will

slow to a stop and then reverse direction.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After making the electrical connections,

spliced conductors should be turned

upward and pushed carefully up into

outlet box. The wires should be spread

apart with the ground wire and white

(common) wire to one side with the black

(load) wire to the other side of the outlet

box.

12. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be ETL Listed and marked suitable

for use with the model fan you are

installing. Switches must be ETL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS

IN THE PATH OF THE BLADES.

1. SAFETY RULES

WARNING

To reduce the risk of ﬁre, electric shock, or

Personal Injury, mount directly to a structural

framing member or to an outlet box marked

'Acceptable for Fan Support of 15.9 kg(35 lbs)

or less'. For outlet box mounting, use mounting

screws provided with the outlet box.

3. WARNING: To reduce the risk of ﬁre or

electric shock, do not use this fan with any

solid-state speed control. Use only the

control provided with the fan.

3. PACKAGE CONTENTS

Unpack your fan and check the contents .

You should have the following items:

A. Ceiling Mounting Plate/Bracket

B. Motor Assembly

C. Blade (3)

D. Blade Trim (3)

E. Switch Housing

F. LED Assembly

G. Glass Shade

H. Light Kit Wire Cover

I. Steel Cap

J. Wall Mount Control System

K. Package hardware

1) Mounting hardware:

wood screws (2), ﬂat washers (2),

screws (2) , lock washers (2),

wire nuts (3)

2) Blade attachment hardware:

Screws (11)

3) Safety cable hardware :

wood screw (1) , spring washer (1),

ﬂat washer (1)

4) Balance kit

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

12 3 4

DIPON

Sola

4. MOUNTING OPTIONS

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

ANGLED CEILING

MAXIMUM 30°ANGLE

If there isn't an existing ETL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of different

ways to mount the outlet box.

NOTE: If you are installing the ceiling fan on a

sloped (vaulted) ceiling, you may need a

longer downrod to maintain proper clearance

between the tip of the blade and the ceiling.

A minimum clearance of 12" is suggested for

optimal operation.

NOTE: Depending on the location you have

selected for installation, you may need to

purchase and install a "Joist Hanger" for the

support of the outlet box. Make sure the joist

hanger you purchase has been designed for

use with ceiling fans. (Fig. 4)

5. HANGING THE FAN

REMEMBER to turn off the power before you

begin installation. This is necessary for your

safety and also the proper programming of the

control system.

To properly install your ceiling fan, follow the

steps below.

Step 1. Pass the 120 Volt supply wires from the

ceiling outlet box through the center of the

mounting bracket. Securely attach the Ceiling

Mounting Plate/Bracket to the ceiling junction

box as shown. ( Fig. 4)

Step 2. Hook the motor body onto the Ceiling

Mounting Plate/Bracket as shown.

You can now proceed with the electrical

wiring of your fan. (Fig. 5)

Fig. 4

Fig. 5

ETL Listed

Outlet Box

Screw

Flat Washer

Ceiling Mounting Plate/Bracket

Hook

Sola

A safety support cable is provided to help prevent

the ceiling fan from failing, please install it as

follows.

Step 1. Drive a wood screw and washers into the

side of the brace that holds the outlet box. Leave

3mm (1/8") of space between the support brace

and the washer. (Fig. 6)

Step 2. Insert the safety cable through the

mounting bracket and one of the holes in the outlet

box into the ceiling. Adjust the length of the safety

cable to reach the screw and washers by pulling the

extra cable through the cable clamp until the overall

lenght is correct, put the end of the cable back

through the cabel clamp, forming a loop at the end

of the cable. Tighten the cable clamp securely. Now,

put the loop in the end of the safety cabel over the

wood screw and under the washer. Tighten the

wood screw securely. (Fig. 7)

NOTE: Although the safety support cable is required

for Canadian installations only. It’s a good idea to

make the attachment with any installation.

WARNING: To avoid possible electrical shock, be

sure you have turned off the power at the main

circuit panel before wiring.

WARNING: If your house wires are different colors

than referenced in this manual, stop immediately.

A professional electrician is recommended to

determine proper wiring.

Follow the steps below to connect the fan to your

household wiring. Use the wire connecting nuts

supplied with your fan. Secure the connector with

electrical tape. Make sure there are no loose wire

stands or connections.

7. MAKE THE ELECTRIC CONNECTIONS

6. INSTALLATION THE SAFETY SUPPORT

NOTE: The CoolTouch Control System is

equipped with 16 code combinations to prevent

possible interference from or to other remote units.

The frequency switches on your receiver and

transmitter have been preset at the factory. Please

recheck to make sure the switches on the transmitter

and receiver are set to the same position, any

combination of settings will operate the fan as long

as the transmitter and receiver are set to the same

opposition. ( Fig. 8) Chainging the orfer of switches

on each switch block, changes the operational

frequency.

Fig. 6

Fig. 7

Fig. 8

Safety Cable Bolt

Wood Screw

Flat Washer

Wood Screw

Spring Washer

Outlet Box

Support Brace

Ceiling

1234

DIPON

Code Switch

Step 1. Motor to Receiver Electrical Connections:

Connect the BLACK wire from the fan to BLACK

wire marked "TO MOTOT L" from the receiver.

Connect the WHITE wire from the fan to the

WHITE wire marked "TO MOTOR N" from the

receiver. Connect the BLUE wire from the fan to

the BLUE wire marked "FOR LIGHT" from the

receiver. Secure all the wire connections with the

plastic wire nuts provided. ( Fig. 9)

NOTE: Fan must be installed at a maximum distance

of 30 feet from the transmitting unit for proper signal

transmission between the transmitting unit and the

fan’s receiving unit.

NOTE: Carefully tuck the wire connections up into

the outlet box.

8 . FINISHING THE INSTALLATION

Step 1. Remove the 3 small screws from the motor

assembly for later use. Lift up the motor housing on

to the Ceiling Mounting Plate/Bracket, align the 3 holes

from both parts. Secure the motor housing to the motor

bracket by using the 3 small screws removed previously.

(Fig. 10)

Step 3. If your outlet box has a ground wire ( green

or bare copper ) connect it to the fan ground wires :

Secure the wire connection with a plastic nut

provided. After connecting the wires, spread them

apart so that the green and white wires are on one

side of the outlet box and black wire is on the other

side. ( Fig. 9)

Step 2. Remote Receiver to Outlet Box Electrical

Connections: Connect the BLACK (hot) wire from

the ceiling to the BLACK wire marked “AC in L”

from the receiver . Connect the WHITE ( neutral )

wire from the ceiling to the WHITE wire marked

“ AC in N” from the Receiver . Secure the wire

connections with the plastic wire nuts provided .

( Fig. 9)

Fig. 9

Fig. 10

1 2 3 4

DIPON

Outlex box

Ground wire

Green wire

White(Neutral)

White (AC IN N)

Blue(FOR LIGHT)

Black(hot)

Black (AC IN L)

White(“TO MOTOR N”)

Black(“TO MOTOR L”)

Screw

Ceiling Mounting

Plate/Bracket

Motor Assembly

Sola

Step 2. Insert the blade through the slots on the

ﬂywheel and attach to the motor hub using the

blade screws and blade tirm. Make sure the screws

securing the blades to the motor hub are tighten

and are properly seated. (Fig. 11)

Step 3. Remove one of the three screws in the

adapter plate at the bottom of the motor assembly

and retain the screw for later use. Slightly loosen the

remaining two screws. Place the motor connector

through the center hole of the switch housing.

Rotate the switch housing key hole slots clockwise

to engage both loosened screws. Reinstall the

previous removed screw. Secure the switch

housing to the adapter plate by tightening the

three screws.(Fig. 12)

Step 4. Remove one of the three screws in the

switch housing. Slightly loosen the remaining

two screws. (Fig. 13)

Fig. 13

Fig. 12

Fig. 11

Adapter Plate

Switch Housing

Screw

Blade Screw

Blade Trim

Blade Flywheel

Motor Hub

Step 5. If installing the light kit, skip to step 7.

Assembly the light kit wire cover to the switch

housing using the two key slots. Replace the

removed screw and secure all three screws.

(Fig. 14a)

Step 6. Assemble the steel cap to the light kit by

twisting in a clockwise direction. (Fig. 14b)

Step 7. for use with light kit Connect the 2

single-pin connectors from the switch housing to the

2 single-pin connectors from LED assembly.

Assemble the LED assembly to the switch housing

using the two key slots. Replace the third screw removed

in step 4 and securely tighten all three screws. (Fig. 15a)

Step 8. Secure the glass shade to switch housing by

twisting in a clockwise direction. Do not over-tighten.

(Fig. 15b)

Fig. 14a

Fig. 14b

Fig. 15b

Fig. 15a

Screw

Light Kit Wire Cover

Switch Housing

Steel Cap

Screw

LED Assembly

Switch Housing

Glass Shade

Sola

10. CONTROL SYSTEM SET-UP

9. INSTALLING THE TRANSMITTER

Step 2. Use the screws provided to secure

the wall transmitter to the outlet box.

(Fig. 17)

Step 2. Test the transmitter by pressing and

releasing ANY button. A RED Light should

illuminate, if not, check to make sure the battery

is inserted and seated correctly. (Fig. 18)

NOTE: Make sure the power is completely

NOTE: Make sure the electrical power is TURNED

OFF at the main panel before continuing.

NOTE: SWITCH INSTALLATION MUST COMPLY

WITH ALL LOCAL AND NATIONAL ELECTRIC

CODE.

disconnected before you begin this procedure.

NOTE: To prevent damage to transmitter ,

remove the battery if not used for long periods

of time ( months ).

Read all of these steps before preceeding.

All wiring nust be in accordance with the National

Electrical Code and local electrical codes. Electrical

installation should be performed by a qualiﬁed

licensed electrician.

Select a location to install your wall mount Control

System Transmitter. You can replace an existing wall

seitch, or install the transmitter to a new outlet box.

Each step must be followed exactly to properly

program the control system.

Step 1. Use a small ﬂat screw driver and gently

pry it apart from the top or bottom of the switch

plate. Install 1, 12volt battery included with wall

mount Control system and make sure it is seated

correctly. Replace the switch plate. (Fig. 18)

Fig. 17

Fig. 18

Step 1. Remove the existing wall plate and

the old switch from the wall outlet box. Wire

nut the BLACK leads (hot) together and

push back inside the outlet box. (Fig. 16)

Or Select the desired location with a new

wall outlet box.

Outlet Box

Switch

Wall Plate

Fig. 16

Outlet Box

Wall Switch

Wall Plate

Wall Switch

Battery

Switch Plate

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting Decor Kimberley Bedienungsanleitung

Kichler Lighting

Kichler Lighting Jade 300030 Bedienungsanleitung

Kichler Lighting

Kichler Lighting VASSAR Bedienungsanleitung

Kichler Lighting

Kichler Lighting Select Sutter Place Bedienungsanleitung

Kichler Lighting

Kichler Lighting VASSAR Bedienungsanleitung

Kichler Lighting

Kichler Lighting Ample Bedienungsanleitung

Kichler Lighting

Kichler Lighting Almere Bedienungsanleitung

Kichler Lighting

Kichler Lighting KLF-SOLA-34-WHT-BN Bedienungsanleitung

Kichler Lighting

Kichler Lighting Surrey Climates 60 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300370 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Universal 3 Light Fitter Bedienungsanleitung

Kichler Lighting

Kichler Lighting Canfield Patio 310192 Bedienungsanleitung

Kichler Lighting

Kichler Lighting sterling manor select Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lehr Decor 80" Bedienungsanleitung

Kichler Lighting

Kichler Lighting Spyn Lite Bedienungsanleitung

Kichler Lighting

Kichler Lighting Highland Manor Bedienungsanleitung

Kichler Lighting

Kichler Lighting Crystal Bay Bedienungsanleitung

Kichler Lighting

Kichler Lighting Rivetta Bedienungsanleitung

Kichler Lighting

Kichler Lighting Fit Bedienungsanleitung

Kichler Lighting

Kichler Lighting FLYY 310700MWH Bedienungsanleitung

Kichler Lighting

Kichler Lighting Vassar 330002OZ Bedienungsanleitung

Kichler Lighting

Kichler Lighting Bentzen Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lucia Bedienungsanleitung

Kichler Lighting

Kichler Lighting 54 Meredith Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung