Kichler Lighting Sterling Manor Bedienungsanleitung

  2*

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

Instruction Manual

Sterling Manor™

A Kichler

Select

™

deiling fan

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local electrical

codes. Electrical installation should be

performed by a qualified licensed

electrician.

3. WARNING: Suitable for use with

solid-state speed controls.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting fixtures are not acceptable for fan

support and may need to be replaced,

consult a qualified electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use only CUL Listed outlet boxes

marked "FOR FAN SUPPORT".

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the floor.

7. Do not operate reversing switch while fan

blades are in motion. Fan must be turned

off and blades stopped before reversing

blade direction.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After marking electrical connections,

spliced conductors should be turned

upward and pushed carefully up into outlet

box. The wires should be spread apart with

the grounded conductor and the

equipment-grounding conductor on one

side of the outlet box.

12. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be CUL Listed and marked suitable

for use with the model fan you are

installing. Switches must be CUL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

OR PERSONAL INJURY, MOUNT FAN TO OUTLET

BOX MARKED "ACCEPTABLE FOR FAN

SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE BRACKETS (ALSO

REFERRED TO AS FLANGES) DURING ASSEMBLY

OR AFTER INSTALLATION. DO NOT INSERT

OBJECTS IN THE PATH OF THE BLADES.

1. SAFETY RULES

3. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items:

a. Fan blades (5)

b. Ceiling mountung bracket

c. Canopy

d. Ball/downrod assembly

e. Fan motor assembly

f. Set of 5 blade brackets and Pre-Installed

mounting screws

g. Switch housing

h. Part bag contents

1) Mounting hardware:

wood screws (2), flat washers (2),

star washers (2), wire nuts (3),

screws (2)

2) Rubber gasket

3) Blade attachment hardware:

screws (17), fiber washers (17)

4) Blade brackets hardware:

screws (2)

5) Safety cable hardware:

wood screw, lock washer, flat washer

6) Pull chain and fob

7) Balance Kit

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

Sterling Manor

4. MOUNTING OPTIONS

If there isn't an existing UL (cUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of different

ways to mount the outlet box.

NOTE: If you are installing the ceiling fan on a

sloped (vaulted) ceiling, you may need a

longer downrod to maintain proper clearance

between the tip of the blade and the ceiling. A

minimum clearance of 12" is suggested for

optimal operation.

NOTE: Depending on the location you have

selected for installation, you may need to

purchase and install a "Joist Hanger" for the

support of the outlet box. Make sure the joist

hanger you purchase has been designed for

use with ceiling fans. (Fig. 4)

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

ANGLED CEILING

MAXIMUM 20°ANGLE

Sterling Manor

5. HANGING THE FAN

Fig. 5

Fig. 6

Fig. 7

Mounting screws

(supplied with

electrical box)

Hook

Ceiling

mounting

bracket

CUL Listed

electrial

box

120V Wires

Washers

Downrod

Cross pin

Hanger

ball Set screw

Cross pin

Hanger

ball Set screw

Supply wires

Downrod

Hitch pin

Retaining clip Set screws

Set screws

Ceiling canopy

NOTE: This ceiling fan is supplied with two

types of hanging assemblies; a downrod and

canopy mounting system and a "close to

ceiling" Canopy ONLY system. The "close-to-

ceiling" installation is recommended in rooms

with less than 8-foot ceilings or in areas where

additional space is desired from the floor to the

fan blades. Once you have selected which

mounting system you will use, proceed with

the following instructions. Where necessary,

each section of the instructions will note the

different procedures to follow for the two types

of mounting.

REMEMBER to turn off the power before you

begin.

To properly install your ceiling fan, follow the

steps below.

Step 1. Pass the 120 volt supply wires from

the ceiling outlet box through the center of the

ceiling mounting bracket. (Fig. 5)

Step 2. Attach the ceiling mounting bracket to

the outlet box using the screws and washers

included with the outlet box. (Fig. 5)

Step 1. Remove the hanger ball from the

downrod assembly by loosening the set screw,

removing the cross pin and sliding the ball off

the rod. (Fig. 6)

Step 2. Loosen the two set screws and

remove the hitch pin and retaining clip from

the coupling on top of the motor assembly.

(Fig. 7)

Step 3. Carefully feed the electrical lead wires

from the fan up through the downrod. Thread

the downrod into the coupling until the Hitch

pin holes are aligned.

Next, replace the hitch pin and retaining clip.

Tighten both set screws. (Fig. 7)

STANDARD CEILING INSTALLATION

Fig. 8

Fig. 9

Fig. 10

Fig. 11

Registration slot

Canopy

Collar

Rubber gasket

Canopy cover

Canopy

Screw and

Lockwasher

(3 of 6 places)

Hook

Step 4. Slip the coupling cover and canopy

onto the downrod as Figure 7.

Thread the hanger ball onto the downrod,

insert the cross pin previously removed from

the ball/downrod assembly through the

downrod and tighten. Now tighten the set

screw previously loosened. (Fig. 6)

Step 5. Lift the motor assembly into position

and place the hanger ball into the ceiling

mounting bracket. (Fig. 8)

Rotate the entire assembly until the "Check

Tab" has dropped into the "Registration Slot"

and seats firmly. (Fig. 8)

The entire motor assembly should not rotate

(left or right) when seated properly.

WARNING: Failure to reattach the cross pin

and seat the "Check Tab" can cause the fan to

fall from the ceiling during operation. Take

special care to make sure this pin is

reattached.

Step 1. Remove the decorative canopy cover

from the canopy. (Fig. 9)

Step 2. Remove three of the six screws and

lock washers (every other one) from the

coupler on top of the motor assembly. Place

the ceiling fan canopy and the rubber gasket

over the coupler and align the mounting holes

with the holes in the coupler. Attach the

canopy with the rubber gasket and the three

screws and lock washers previously removed.

(Fig. 10)

WARNING: Failure to completely tighten the

three mounting screws in step 10 could result

in the fan possibly falling from the ceiling.

Step 3. Hang the fan on the ceiling mounting

bracket by inserting the hook on the inside

edge of the ceiling mounting bracket through

one of the screw holes in the ceiling canopy

(Fig. 11). This will allow you to have both

hands free to make the wiring connections.

CLOSE-TO-CEILING INSTALLATION

Fig. 12

Sterling Manor

Hanger bracket Attach

safety cable

to ceiling joist

with screw and

washer

Fig. 13

7. ELECTRIC CONNECTIONS

BLK

BLUE

BLK

GRN

Wiring

box

Ground to

mounting

bracket

or downrod

Power lines 120v

Green ground

A safety support cable is provided to help

prevent the ceiling fan from falling, please

install it as follows.

Step 1. Attach the provided wood screw and

washers to the ceiling joist next to the

mounting bracket but do not tighten. (Fig. 12)

Step 2. Adjust the length of the safety cable to

reach the screw and washers by pulling the

extra cable through the cable clamp until the

overall length is correct, put the end of the

cable back through the cable clamp, forming a

loop at the end of the cable. Tighten the cable

clamp securely. Now, put the loop in the end of

the safety cable over the wood screw and

under the washer. Tighten the wood screw

securely.

NOTE: Although the safety support cable is

required for Canadian installations only. It's a

good idea to make the attachment with any

installation.

WARNING: To avoid possible electrical shock,

be sure you have turned off the power at the

main circuit panel.

Follow the steps below to connect the fan to

your household wiring. Use the wire

connecting nuts suppled with your fan. Secure

the connectors with electrical tape. Make sure

there are no loose wire strands or

connections.

Step 1. Connect the fan supply (black) wire

and light supply (blue) wire to the black

household supply wire as shown in Figure 13.

Step 2. Connect the neutral fan (white) wire to

the neutral household (white) wire.

Step 3. Connect the fan ground wire (green) to

the household ground wire.

Step 4. After connecting the wires, spread

them apart so that the green and white wires

are on one side of the outlet box and the black

and blue wires are on the other side.

Step 5. Turn the connecting nuts upward and

push the wiring into the outlet box.

6. INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

Fig. 15

Fig. 14

Outlet box

Ceiling mounting

bracket

Canopy

Screws

Outlet box

Ceiling mounting

bracket Hook

Canopy

CLOSE-TO-CEILING INSTALLATION

Step 1. Tuck all the wire connections neatly

above the receiver and into the ceiling outlet

box.

Step 2. Remove the fan from the hook on the

ceiling mounting bracket. Attach the fan

assembly to the ceiling mounting bracket

using 4 screws at the top edge of the

mounting bracket.

Align the keyhole slots on the canopy with the

mounting screw heads on the sides of the

mounting bracket. Lift up and turn the fan

assembly until the heads of the mounting

screws are in the narrow end of the keyhole

slots.

Step 3. Make sure all four mounting screws

are tight. (Fig. 15)

8. FINISHING THE INSTALLATION

STANTARD CEILING INSTALLATION

Step 1. Tuck all the connections neatly into the

ceiling outlet box.

Step 2. Slide the canopy up to ceiling and

attach the canopy to the ceiling mounting

bracket using 4 screws at the top edge of the

mounting bracket. Insert each screw through

the canopy mounting hole and into the

mounting bracket. Tighten all screws securely.

(Fig. 14)

Sterling Manor

9. ATTACHING THE FAN BLADES

Fig. 16

Fig. 17

CAUTION: Remove the five rubber shipping

blocks attached to the face of the motor.

These blocks keep the motor from shifting

during shipping and MUST be removed during

installation.

Step 1. Attach the blade to the blade bracket

using the screws and fiber washers as shown

in Figure 16. Start screw into bracket. Repeat

for the two remaining screws.

Step 2. Make sure the blade is straight and

tighten each screw.

Step 3. Fasten blade assembly to motor using

"Pre-Installed" mounting screws in the blade

bracket.

10. INSTALLING THE SWITCH HOUSING

NOTE: Before starting installation, disconnect

the power by turning off the circuit breaker or

removing the fuse at fuse box. Turning power

off using the fan switch is not sufficient to

prevent electric shock.

1. While holding the switch housing under

your ceiling fan, push the square wire

connectors together. One from the fan and on

from the switch housing.

NOTE: These connectors are color coded and

will ONLY engage when the colored strips are

matched (aligned).

2. Carefully push all the wires into the switch

housing.

Attach the switch housing to the mounting

plate with the screws provided. Make sure

each screw is tight.

Screws Blade

Blades bracket

Screws

Fiber

washers

Switch

housing

Wire connector

Screws

Mounting plate

Fig. 18

Fig. 19

11. OPERATING INSTRUCTIONS

Turn the power on and check the operation of

your ceiling fan.

The pull chain controls the 3 speeds of your

ceiling fan as follows:

1 pull = High, 2 pulls = Medium, 3 pulls = Low

and the 4th pull turns the motor off.

The Black Slide Switch on the side of the

switch housing controls the direction of the

blades "Forward and Reverse".

Warm weather - Forward (counter clockwise)

A downward airflow creates a cooling effect

as shown in Fig. 18. This allows you to set

your air conditioner on a warmer setting

without affecting your comfort.

Cool weather - Reverse (clockwise) An

upward airflow moves warm air off the ceiling

area as shown in Fig. 19. This allows you to

set your heating unit on a cooler setting

without affecting your comfort.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting Terna 300230 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Starkk 330180MWH Bedienungsanleitung

Kichler Lighting

Kichler Lighting KAPONO Bedienungsanleitung

Kichler Lighting

Kichler Lighting Arkwet Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting Renew Premier Bedienungsanleitung

Kichler Lighting

Kichler Lighting Maor 310136 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 52" Chiara LED Bedienungsanleitung

Kichler Lighting

Kichler Lighting Surrey Climates 60 Bedienungsanleitung

Kichler Lighting

Kichler Lighting ELLYS Bedienungsanleitung

Kichler Lighting

Kichler Lighting 52" Basics Pro Bedienungsanleitung

Kichler Lighting

Kichler Lighting Olympia Bedienungsanleitung

Kichler Lighting

Kichler Lighting Saxon Premier Bedienungsanleitung

Kichler Lighting

Kichler Lighting IMARI 300365SBK Bedienungsanleitung

Kichler Lighting

Kichler Lighting Starkk Bedienungsanleitung

Kichler Lighting

Kichler Lighting 380106 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lija 330140NI Bedienungsanleitung

Kichler Lighting

Kichler Lighting Hatteras Bay Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lucia Bedienungsanleitung

Kichler Lighting

Kichler Lighting 54 inch Skye Bedienungsanleitung

Kichler Lighting

Kichler Lighting Makoda Bedienungsanleitung

Kichler Lighting

Kichler Lighting Crystal Bay Bedienungsanleitung

Kichler Lighting

Kichler Lighting Guardian 330057 Bedienungsanleitung

Kichler Lighting

Kichler Lighting FLYY 310700MWH Bedienungsanleitung

Kichler Lighting

Kichler Lighting Starkk 330174OZ Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung