Kichler Lighting Canfield Bedienungsanleitung

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local electrical

codes. Electrical installation should be

performed by a qualified licensed

electrician.

3. WARNING: Suitable for use with solid-

state speed controls.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting fixtures are not acceptable for fan

support and may need to be replaced,

consult a qualified electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use only CUL Listed outlet boxes

marked "FOR FAN SUPPORT".

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the floor.

7. To operate the reverse function on this fan,

press the reverse button while the fan is

running.

8. WARNING: Use only with light kit marked

"Suitable for Use in Damp Locations".

9. Avoid placing objects in the path of the

blades.

10. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

11. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

12. After marking electrical connections,

spliced conductors should be turned

upward and pushed carefully up into outlet

box. The wires should be spread apart with

the grounded conductor and the

equipment-grounding conductor on one

side of the outlet box.

13. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be CUL Listed and marked suitable

for use with the model fan you are

installing. Switches must be CUL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT FAN TO

OUTLET BOX MARKED "ACCEPTABLE FOR FAN

SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE BRACKETS (ALSO

REFERRED TO AS FLANGES) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT

INSERT OBJECTS IN THE PATH OF THE BLADES.

1. SAFETY RULES

3. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items:

a. Fan blades (5)

b. Hanger bracket and canopy

c. Ball/downrod assembly

d. Coupling cover

e. Fan motor assembly

f. Set of blades brackets (5)

g. Mounting plate

h. Switch housing

i. Part bag contents

1) Mounting hardware :

wood screws (2), flat washers (2),

star washers (2), wire nuts (3)

2) Blade attachment hardware:

screws (17), washers (17),

rubber washers (17)

3) Blade brackets hardware:

screws (10)

4) Safety cable hardware:

wood screw, lock washer, flat washer

5) Close mount hardware:

screw with lock washers (3)

6) Pull chain and fob

7) Balance Kit

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

CanfieldTM

4. MOUNTING OPTIONS

If there isn't an existing UL (CUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power

by removing fuses or turning off circuit

breakers

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1,2 and 3 are examples of different

ways to mount the outlet box.

NOTE: You may need a longer downrod to

maintain proper blade clearance when

installing on a steep, sloped ceiling. (Fig. 3)

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Fig 4.

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

ANGLED CEILING

MAXIMUM 20°ANGLE

CanfieldTM

Fig. 6

Fig. 7

Fig. 8

Mounting screws

(supplied with

electrical box)

Hook

Ceiling

mounting

bracket

CUL Listed

electrial

box

120V Wires

Washers

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly. NOTE:

This ceiling fan is supplied with two types of

hanging assemblies; the standard ceiling

installation using the downrod with ball and

socket mounting and the "close-to-ceiling"

installation. The "close-to-ceiling" installation is

recommended in rooms with less than 8-foot

ceilings or in areas where additional space is

desired from the floor to the fan blades. When

using the standard 6" downrod, the distance

from the ceiling to the bottom of the fan blades

will be approximately 10 inches. The "close-to-

ceiling" installation reduce this distance to 8-

inches. Once you have selected which

mounting system you will use, proceed with

the following instructions. Where necessary,

each section of the instructions will note the

different procedures to follow for the two types

of mounting.

STANDARD CEILING INSTALLATION

1. Remove the canopy ring from the canopy.

(Fig. 5)

2. Remove the hanger bracket from the canopy

by loosening the four screws on the top of the

canopy. Remove the two non-slotted screws

and loosen the slotted screws. This will enable

you to remove the hanger bracket. (Fig. 5)

Step 3. Secure the hanger bracket to the

ceiling outlet box using screws and washers

included with your outlet box. (Fig. 6)

Step 4. Remove hanger ball from downrod

assembly by loosening set screws, removing

the cross pin, and sliding ball off rod. (Fig. 7)

Step 5. Loosen the two set screws and

remove the hitch pin and lock pin from the top

coupling of the motor assembly. (Fig. 8)

Step 6. Carefully feed the fan wires up through

the downrod. Thread the downrod into the

coupling until the Hitch pin holes are aligned.

Next, replace the lock clip and hitch pin then

tighten the set screws. (Fig. 8)

Downrod

Cross pin

Hanger

ball Set screw

Fig. 5

Hanger bracket

Ceiling

canopy

Canopy

Ring

Supply wires

Downrod

Hitch pin

Lock pin Set screws

Set screws

5. HANGING THE FAN

Fig. 9

Fig. 10

Registration slot

Downrod Canopy

Canopy cover

Coupling cover

Step 7. Slip coupling cover, canopy ring and

canopy onto downrod. Carefully reinstall

hanger ball onto rod being sure that cross pin

is in correct position, the set screw on hanger

ball is tight and wires are not twisted. (Fig. 9)

Step 8. Now lift the motor assembly into

position and place the hanger ball into the

hanger bracket. Rotate until the "Check Tab"

has dropped into the "Registration Slot" and

seats firmly. (Fig. 10). The entire motor

assembly should not rotate if this is done

correctly.

Set screws

Hitch pin Lock pin

Fig. 11

Fig. 12

Fig. 13

1. Remove the decorative canopy cover from

the canopy. (Fig. 11)

2. Pass the 120-volt supply wires through the

center hole in the ceiling hanger bracket as

shown in Fig. 6.

3. Secure the hanger bracket to the ceiling

outlet box with the screws and washers

provided with your outlet box. (Fig. 6)

4. Tighten the two screws on the outlet box

securely.

5. Place the rubber gasket over the remaining

three screws, route the wires exiting the top of

the fan motor through the canopy ring (make

sure the slot openings of the ring are on top).

then proceed to place the ceiling canopy over

the collar at the top of the motor. Align the

mounting holes with the holes in the motor and

fasten using the screws and lock washers

provided. (Fig. 12).

6. Tighten the mounting screws securely.

(Fig. 12)

WARNING: Failure to completely tighten the

three screws in step 6 could result in fan

loosening and possibly falling.

7. Hang the fan on the hook of the hanger

bracket. Be certain that the canopy is fully

locked into hook as shown in Fig. 13.

CanfieldTM

CLOSE-TO-CEILING INSTALLATION

Screw and

Lockwasher

Canopy

Collar Canopy ring

Canopy cover

Canopy

Hook

Fig. 14

Fig. 15

Fig. 16

7. MAKE THE ELECTRIC CONNECTIONS

Remember to disconnect the power.

Follow the steps below to connect the fan to

your household wiring. Use the wire

connecting nuts supplied with your fan.

Secure the connectors with electrical tape.

Make sure there are no loose strands or

connections.

Step 1 Connect the fan supply (black) wire and

light supply (blue) wire to the black household

supply wire as shown in Figure 15.

Step 2. Connect the neutral fan (white) wire to

the white neutral household wire.

Step 3 Connect the fan ground wire (green) to

the household ground wire.

Step 4 After connecting the wires, spread

them apart so that the green and white wires

are on one side of the outlet box and the black

and the blue wires are on the other side.

Step 5 Turn the connecting nuts upward and

push the wiring into the outlet box.

6. INSTALLATION OF SAFETY SUPPORT

(for Canadian Installation ONLY)

Wiring

box

Ground to

mounting

bracket

or downrod

Power lines 120v

BLUE

BLK BLK

FAN

LIGHT

BLK

BLUE WH

Light

switch

Green ground

BLUE

BLK BLK

GRN

Wiring

box

Ground to

mounting

bracket

or downrod

BLUE

BLK WH

FAN

LIGHT

Power lines 120v

Green ground

An additional safety support is provided to

prevent the fan from falling fan). Place the end

of cable through the loop of ceiling support

cable. Pull as much cable through loop as

possible. Feed end of cable into clamp hole

and fi rmly tighten screw (Fig. 14). Cut off

excess safety cable. Secure the safety cable

to the ceiling joist with screw and washer.

Hanger bracket Attach safety cable

to ceiling joist with

screw and washer

CanfieldTM

Fig. 17

Fig. 18

Fig. 19

STANDARD CEILING INSTALLATION

Slide canopy up to the ceiling as shown in Fig.

18. Make sure you place the wires safely into

the outlet box. Secure the canopy to the

hanger bracket with the four screws with your

fan. Raise canopy ring up against canopy and

secure it to canopy until snug.

CLOSE-TO-CEILING INSTALLATION

Remove the fan from the hook on the hanger

bracket. Secure the canopy to the hanger

bracket as shown in Fig. 19 with four screws

included with your fan. Secure the canopy to

the hanger bracket with the four screws with

your fan. Raise canopy ring up against canopy

and secure it to canopy until snug.

Figures 16 and 17 illustrate the wiring

connections for optional wall control (The wire

color out of wall control may vary, see wall

control's installation manual for correct wire

connections.)

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR OTHER PERSONAL

INJURY. MOUNT FAN ONLY ON AN

OUTLET BOX OR SUPPORTING SYSTEM

MARKED ACCEPTABLE FOR FAN

SUPPORT.

8. FINISHING THE INSTALLATION

GROUND TO

MOUNTING

BRACKET

OR DOWNROD

POWER LINES 120V

GREEN

GROUND

WIRING

BOX

BLUE

BLK BLK

FAN

LIGHT

BLUE

BLK

LIGHT FAN

Outlet box

Hanger

bracket

Screws

Outlet box

Hanger

bracket

Canopy

Screws

Ceiling canopy

Canopy ring

9. ATTACHING THE FAN BLADES

Fig. 20

Fig. 21

Caution: Remove 5 rubber packing mounts

and discard before installation.

Step 1 Attach the blade to the blade bracket

using the screws, washers and rubber

washers as shown in Fig. 20. Start screw into

bracket. Repeat for the two remaining screws.

Step 2 Make sure the blade is straight and

tighten each screw.

Step 3 Fasten blade assembly to motor using

"Pre-Installed" mounting screws in the blade

bracket.

10. INSTALLING THE MOUNTING PLATE

1. Remove 1 of the 3 screws from the

mounting ring and loosen the other 2 screws.

(Do not remove)

2. Place the key holes on the mounting plate

over the 2 screws previously loosened from

the mounting ring, turn mounting plate until it

locks in place at the narrow section of the key

holes. Secure by tightening the 2 screws

previously loosened and the one previously

removed. (Fig. 21)

Screws Blade

Blades bracket

Screws

Washers

Rubber

washers

Mounting

plate

Mounting ring

Screws

Andere Handbücher für Canfield

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting Cortez Bedienungsanleitung

Kichler Lighting

Kichler Lighting Wilton Bedienungsanleitung

Kichler Lighting

Kichler Lighting Renew Premier Bedienungsanleitung

Kichler Lighting

Kichler Lighting Salvo 330045 Bedienungsanleitung

Kichler Lighting

Kichler Lighting RIDLEY2 KLF-RIDLEY2-52-NB Bedienungsanleitung

Kichler Lighting

Kichler Lighting Eads 310135 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lehr Decor 80" Bedienungsanleitung

Kichler Lighting

Kichler Lighting Motu Bedienungsanleitung

Kichler Lighting

Kichler Lighting 380106 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Selectlight fixture Bedienungsanleitung

Kichler Lighting

Kichler Lighting LYNDON Bedienungsanleitung

Kichler Lighting

Kichler Lighting Decor Link Bedienungsanleitung

Kichler Lighting

Kichler Lighting 310155 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Emerson HIGH COUNTRY Bedienungsanleitung

Kichler Lighting

Kichler Lighting Compass 300322 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Richland II Bedienungsanleitung

Kichler Lighting

Kichler Lighting 52 inch Colerne LED Bedienungsanleitung

Kichler Lighting

Kichler Lighting Saxon Premier Bedienungsanleitung

Kichler Lighting

Kichler Lighting ETL Bedienungsanleitung

Kichler Lighting

Kichler Lighting Larissa Bedienungsanleitung

Kichler Lighting

Kichler Lighting 339211APP Bedienungsanleitung

Kichler Lighting

Kichler Lighting Starkk Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35208 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300370 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung