Kichler Lighting Lucia Bedienungsanleitung

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

A Kichler®Décor™Ceiling Fan

Instruction Manual

Includes our new

CoolTouchTM Control System

Looks permanent, but goes wherever you go!

U.S. Patent Pending

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local electrical

codes. Electrical installation should be

performed by a qualified licensed

electrician.

3. WARNING: Suitable for use with solid-

state speed controls.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting fixtures are not acceptable for fan

support and may need to be replaced,

consult a qualified electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use only CUL Listed outlet boxes

marked "FOR FAN SUPPORT".

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the floor.

7. To operate the reverse function on this fan,

press the reverse button while the fan is

running.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After making the electrical connections,

spliced conductors should be turned

upward and pushed carefully up into outlet

box. The wires should be spread apart with

the ground wire and white (common) wire

to one side with the black (load) wire to the

other side of the outlet box.

12. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be CUL Listed and marked suitable

for use with the model fan you are

installing. Switches must be CUL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

OR PERSONAL INJURY, MOUNT FAN TO OUTLET

BOX MARKED "ACCEPTABLE FOR FAN

SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE BRACKETS (ALSO

REFERRED TO AS FLANGES) DURING ASSEMBLY

OR AFTER INSTALLATION. DO NOT INSERT

OBJECTS IN THE PATH OF THE BLADES.

1. SAFETY RULES

Special Notice

This appliance is equipped with a "Wattage

Limiting Device" required by the United

States Department of Energy. The device

has been installed at the factory and can not

be removed.

Installing Lamps in excess of 190 total watts

will disable the unit's light fixture. If this

should happen, you will need to reset the

lighting fixture by turning the power off to

the ceiling fan and/or light fixture,

reinstalling lamps totaling less that 190

watts and then turning the power back on.

3. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items:

Philips screw driver

Slot screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

LuciaTM

a. Ceiling Mounting Bracket (1)

b. Canopy (1)

c. Canopy Cover (1)

d. Decorative Ring (1)

e. Ball / Downrod Assembly (1)

f. Decorative Arm (3)

g. Coupling Cover (1)

h. Upper Glass Bowl (1)

i. Fan Assembly (1)

j. Fan Blades (5)

k. Set of Blade Brackets (5)

l. Mounting Plate (1)

m. Switch Housing for no light kit (1)

n. Light Fixture Assembly (1)

o. Inner Glass Bowl (1)

p. Outer Glass Bowl (1)

q. Receiver + 7 Wire Nuts

r. CoolTouch™ Control System

s. Candelabra Bulbs (4)

t. Halogen Bulbs (2)

u. Package Hardware:

1) Mounting hardware:

a. wood screws (2), flat washers(2),

screws(2),wire nuts(4)

2) Blade Attachment Hardware:

a. screws (21), flat washers(21),

fiber washers(21)

3) Blade Bracket Hardware:

a. screws (11)

4) Safety Cable Hardware:

a. wood screw (1), spring washer (1),

flat washer (1)

5) Balance Kit (1)

v. Light kit Hardware:

a. manual nut (1), silicon washer (1),

metal washer (1), finial (1)

w. Mounting Plate Hardware:

a. glass mounting plates(3), manual nuts (3)

4. MOUNTING OPTIONS

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1,2 and 3 are examples of different

ways to mount the outlet box.

NOTE: If you are installing the ceiling fan on a

sloped (vaulted) ceiling, you may need a longer

downrod to maintain proper clearance between

the tip of the blade and the ceiling. A minimum

clearance of 12" is suggested for optimal

operation.

NOTE: Depending on the location you have

selected for installation, you may need to

purchase and install a "Joist Hanger" for the

support of the outlet box. Make sure the joist

hanger you purchase has been designed for

use with ceiling fans. (Fig. 4)

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

Installation) listed mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

If there isn't an existing UL ( cUL for Canadian

LuciaTM

5. HANGING THE FAN

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly:

Remove the fan motor and housing assembly

from the protective plastic bag and take the lower

Styrofoam packing out of the carton. Place the

styrofoam on the floor. Place the fan assembly

on the styrofoam for protection while working /

assembling the fan.

To properly install your ceiling fan, follow the steps

below.

Step 1. Pass the 120 volt supply wires from the

ceiling outlet box through the center of the ceiling

mounting bracket. (Fig.6)

Step 2. Attach the ceiling mounting bracket to the

outlet box using the screws and washers included

with the outlet box. (Fig. 6)

Step 3. Remove the hanger ball from the downrod

assembly by loosening the set screw, removing the

Step 4. Loosen the two set screws and remove the

hitch pin and retaining clip from the coupling on top

of the motor assembly. (Fig. 8)

Step 5. Carefully feed the electrical lead wires from

the fan up through the downrod. Thread the downrod

into the coupling until the Hitch pin holes are aligned.

Next, replace the hitch pin and retaining clip. Tighten

both set screws. (Fig 8)

Fig. 7

Fig. 5

Fig. 6

Fig. 8

Set Screw

Cross Pin

Hanger Ball

Downrod

Shipping Block

Downrod

Supply wires

Hitch pin

120 V wires

Listed electrial box

Washer

Mounting screw

Ceiling Mounting Bracket

Retaining clip

cross pin and slide the ball off the rod. (Fig.7)

Step 8. Remove the three (3) decorative wire

arms from the packing. Note that, one end of

each set of wires are welded together. Feed

the welded end of the wire through the

decorative ring on the downrod and fit the

other end into the holes on the decorative

bracket. (see Fig. 11). Repeat this process

for the other two (2) decorative wire arms,

then tighten the set screw on the decorative

ring as shown.

Step 10. Now lift the motor assembly into position

and place the hanger ball into the ceiling mounting

bracket. Rotate the motor assembly until the

"Check Tab" on the mounting bracket has dropped

into the "Registration Slot" on the hanging ball and

seats firmly. (Fig. 13)

Step 9. Install four (4) 15 watt lamps (included).

One in each of the sockets. (Fig. 12)

Step 7. Loosen the set screws preinstalled on

the decorative ring. Slip the coupling cover,

decorative ring, canopy cover and canopy onto

the downrod. Reinstall the hanger ball onto the

downrod and make sure the cross pin is in

place and the set screw on hanger ball is tight.

(Fig. 10)

Step 6. Carefully pass the upper glass bowl

over the downrod and let it rest on top of the

motor housing. Align the slot on the mounting

plate with the screw stem on the motor hous-

ing. Set the mounting plate so the screw stem

comes through the slot on the mounting plate

with the bottom curled end of the mounting

plate resting against the side of the glass

bowl. Tighten the manual nut provided.

Repeat this process for the remainig two

mounting plates. (Fig. 9)

NOTE: The entire motor assembly should not

rotate if this is done correctly.

NOTE: Please make sure all set screws are in

place and tight before installation the following

steps.

Fig. 9

Fig. 10

Fig. 11

Fig. 12

Bulb

Canopy

Canopy Cover

Coupling Cover

Decorative Ring

Manual Nut

Fan Assembly

Upper Glass Bowl

Mounting Plate

Decorative bracket

Screw

Decorative Ring

Decorative arm

Fig. 13

Registration slot

Ceiling Mounting Bracket

Check

tap

LuciaTM

6. INSTALLATION OF SAFETY SUPPORT

( For Canadian Installation ONLY )

Fig. 15

Fig. 16

7. MAKE THE ELECTRIC CONNECTIONS

Code switch

Battery Compartment

Receiver

Hanger

bracket

A safety support cable is provided to help

prevent the ceiling fan from falling, please install

it as follows.

Step 1. Attach the provided wood screw and

washers to the ceiling joist next to the mounting

bracket but do not tighten. See Figure 14-1

Step 2. Adjust the length of the safety cable to

reach the screw and washers by pulling the

extra cable through the cable clamp until the

owerall length is correct, put the end of the

cable back through the cable clamp, forming a

loop at the end of the cable. Tighten the cable

clamp securely. Now, put the loop in the end of

the safety cable over the wood screw and under

the washer. Tighten the wood screw securely.

See Figure 14-2

WARNING: To avoid possible electrical shock,

be sure the electricity is turned off at the main

circuit breaker or fuse box before wiring.

NOTE: The CoolTouch™ Control System is

equipped with 16 code combinations to prevent

possible interference from or to other remote

units. The frequency switches on your receiver

and transmitter have been preset at the factory.

Please recheck to make sure the switches on the

transmitter and receiver are set to the same

position, any combination of settings will operate

the fan as long as each switch on the transmitter

and receiver are set to the same position. (Fig.

15) Changing the order of switches on each

switch block, changes the operational frequency.

Step 1. Insert the receiver into the ceiling mounting

bracket with the flat side of the receiver facing the

ceiling. (Fig. 16)

For best performance, make sure the Black Antenna,

on the end of the receiver, remains extended and not

tangled with any of the electrical wires.

Step 2. Motor to Receiver Electrical Connections:

(Fig. 17, next page)

Connect the black wire from the fan to the black wire

marked "TO MOTOR L" on the receiver.

Connect the white wire from the fan to the white wire

marked "TO MOTOR N" on the receiver.

Connect the blue wire from the fan to the blue wire

marked "FOR LIGHT" on the receiver.

Connect the Orange wire from the fan to the Orange

wire from the receiver marked "For Upper Light".

(Fig. 17)

NOTE: Some model fans may not have Upper Lights

OR the Orange wires

Secure each set of wire connections with the plastic

wire nuts provided in the parts bag.

Fig. 14-1

Fig. 14-2

Safety CableCable Clamp

Wood Screw

Flat Screw

Spring Washer

Ceiling

Support Brace

Outlet Box

Wood Screw

Fig. 18

Step 3. Receiver to Supply Wires Electrical

Connections: (Fig. 17)

Connect the black (load) wire from the ceiling

outlet box to the black wire marked "AC in L"

on the receiver.Connect the white (neutral) wire

from the ceiling outlet box to the white wire

marked "AC in N" on the receiver.

with the plastic wire nuts provided in the parts

bag.

Step 4. Connect the ground wire (green or bare

copper) from the outlet box to the ground wire on

the ceiling mounting bracket and the ground wire

from the ceiling fan.

After making all connections, separate the white

and green wire connections to one side and the

black wire connections to the other side of the

outlet box.Carefully tuck all wire connections up

into the outlet box.

Fig. 17

8. INSTALLING THE CEILING CANOPY

NOTE: For optimal operation and signal

transmission, the CoolTouch™ Remote

Transmitter should be installed and/or

operated at a maximum distance of 30

feet from the ceiling fan receiver.

Step 2. Slide the canopy up to ceiling and onto

the two screws on hanger bracket. Rotate the

canopy clockwise and tighten the two screws.

Next, while holding the canopy with one hand,

slide the canopy décor over the screws and

rotate clockwise until tight.

Step 1. Make sure all of the electrical connec-

tions are tucked neatly into ceiling outlet box.

WARNING: One last time, make sure the

“Check Tab” at the bottom of the hanger bracket

is properly seated in the “Registration Slot” on

the side of the hanger ball before attaching the

canopy to the bracket. Failure to properly seat

the “Check Tab” could damage the electrical

wires when to ceiling fan blade direction is

changed while the fan is running.

NOTE: You may need to adjust the canopy

mounting screws as necessary until the canopy

and canopy cover have a snug fit. (Fig. 18)

Canopy Cover

Canopy

Screw

Hanger bracket

Outlet box

Blue(motor)

Black(motor)

White(neutral)

White("to motor N")

Receiver

Ground Wire

Orange

(for upper light)

Blue

(for bottom light)

Black("to motor L")

White("AC IN N")

Green or bare

copper(ground)

White(neutral)

Black("AC IN L")

Black(hot)

Outlet box

Orange(motor)

Secure each set of electrical connections

LuciaTM

9. ASSEMBLYING AND ATTACHING

THE FAN BLADES

Fig. 19

Fig. 20

Fig. 21

Step 1. Attach the blade to the blade bracket

using the screws, washers and fiber washers

provided. Refer to Fig. 19 as needed. Start

each screw into bracket. Repeat for the three

(3) remaining screws.

Step 2. Make sure the blade is straight and

tighten each screw until the fiber washer is

slightly compressed and all four screws are

secure.

Step 3. Insert the blade assembly into one of

the slots on the blade bracket ring, align the

mounting holes on the blade bracket with the

mounting holes on the inside of the bracket

ring and insert two (2) mounting screws and

tighten securely. Repeat this procedure for the

remaining Four (4) blade assemblies. See Fig.

20 as needed.

10. INSTALLATING THE MOUNTING PLATE

Step 2. Place the key holes on the mounting

plate over the 2 screws previously loosened.

Turn the mounting plate until it locks in place

at the narrow end of the key holes. Replace

the screw you removed and securely tighten

all three. (Fig. 21)

Step 1. Remove 1 of the 3 screws on the

mounting ring (located on the motor shaft)

and loosen the other 2 screws but do not

remove them.

Screw

Metal Washer

Fiber Washer Blade

Blade Bracket

Blade

Blade Bracket

Blade Bracket Ring Screw

Mounting Plate

Molex Connection

Screw

fan, please skip to step 12 and continue.

without the down light fixture, follow step

11 and then skip to step 14.

Mounting Ring

If you want your ceiling fan installed

light fixture that came with your ceiling

NOTE: If you plan on installing the down

Fig. 23

Fig. 22

11. INSTALLING THE SWITCH HOUSING

NOTE: Before continuing, make sure the power

is disconnected by turning off the circuit breaker

of removing the fuse at the circuit box.

Step 1. Remove 1 of the 3 screws on the edge of

the mounting plate and loosen the other 2

screws, do not remove.

Step 2. Connect the black wire connectors from

the switch housing and fan assembly by pushing

them together. Follow the same procedure with

the white wire connectors. (Fig. 22)

Step 3. Tuck the new connections neatly into the

switch housing. Align the key holes on the switch

housing with the 2 screws on the mounting plate.

Rotate the switch housing until it locks in place at

the narrow end of the key holes. Tighten all three

screws. (Fig. 22)

12. INSTALLING THE LIGHT KIT

PROCEED TO STEP 14

Molex Connector

Switch Housing

Mounting Plate

Screw

Mounting Plate

Molex Connector

Step 1. Remove 1 of the 3 screws on the

mounting plate and loosen the other 2 screws.

(Do not remove)

Step 2. Connect the black wire connectors from

the Light Fixture and the fan assembly by pushing

them together. Follow the same procedure with

the white wire connectors. (Fig. 23)

Step 3. Tuck all wire connections neatly into the

mounting plate. Align the key holes on the light

fixture with the screws on the mounting plate, turn

the light fixture until it locks in place at the narrow

end of the key holes. Tighten all screws. (Fig. 23)

Light Fixture

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting 339211APP Bedienungsanleitung

Kichler Lighting

Kichler Lighting FERRON Bedienungsanleitung

Kichler Lighting

Kichler Lighting Crescent 300325 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Arkwright Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300260/60-GENT Series Bedienungsanleitung

Kichler Lighting

Kichler Lighting Arkwet Weather+ Bedienungsanleitung

Kichler Lighting

Kichler Lighting RIDLEY2 KLF-RIDLEY2-52-NB Bedienungsanleitung

Kichler Lighting

Kichler Lighting Vinea 52 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Compass 300322 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Jade 300030 Bedienungsanleitung

Kichler Lighting

Kichler Lighting 54 Skye LED Bedienungsanleitung

Kichler Lighting

Kichler Lighting 54 inch Skye Bedienungsanleitung

Kichler Lighting

Kichler Lighting Harbour Walk Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting Logan Bedienungsanleitung

Kichler Lighting

Kichler Lighting Verdi Bedienungsanleitung

Kichler Lighting

Kichler Lighting Rivetta Bedienungsanleitung

Kichler Lighting

Kichler Lighting Almere Bedienungsanleitung

Kichler Lighting

Kichler Lighting ZEUS KLF-ZEUS-60-WHT-BN Bedienungsanleitung

Kichler Lighting

Kichler Lighting Select Canfield 300107 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Seaside Bedienungsanleitung

Kichler Lighting

Kichler Lighting Starkk 330180MWH Bedienungsanleitung

Kichler Lighting

Kichler Lighting Bronson Bedienungsanleitung

Kichler Lighting

Kichler Lighting Canfield Bedienungsanleitung

Kichler Lighting

Kichler Lighting ETL Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung