Kidde KIR-COD Montageanleitung

KIR-COD Intelligent CO

Sensor Installation Sheet

Carbon monoxide alarm procedure

WARNING: The carbon monoxide (CO) alarm indicates the presence

of CO, which can kill you. If the alarm signal sounds four times, pauses

for five seconds, and then repeats the pattern, follow the steps shown

below.

1. Move to fresh air immediately —outdoors or by an open door or

window. Check that all persons are accounted for. Do not reenter

the premises or move away from the open door or window until

emergency services responders have arrived, the premises have

been aired out, and your detector remains in normal condition.

2. Call emergency services, the fire department, or 911:

Phone:

Information about carbon monoxide

WARNINGS

•Read these installation instructions in their entirety before

proceeding. Leave these instructions with the owner/user of this

CO detection equipment.

•This product is intended for use in indoor locations of dwelling

units. It is not designed to comply with Occupational Safety and

Health Administration (OSHA) commercial or industrial standards.

•The detector only indicates the presence of CO gas at the

detector. Carbon monoxide gas may be present in other areas.

•Failure to properly install, test, and maintain a CO detector may

cause it to fail, potentially resulting in loss of life.

•Installation of this detector is not a substitute for proper installation,

use, and maintenance of fossil fuel-burning appliances, including

appropriate ventilation and exhaust systems.

•To reduce the risk of CO poisoning, test the detector operation

when not in use for 10 days or more.

•This detector does not operate without electrical power. As fires

frequently cause power interruption, discuss further safeguards

with the authority having jurisdiction (AHJ).

•Do not paint the detector.

Notes

•Regulatory code may require that the system generate a three-

pulse temporal code (TC3) for fire alarms and a four-pulse

temporal code (TC4) for CO alarms.

•The CO sensor is calibrated at the factory. CO sensitivity is set to

conform to UL 2034 requirements and cannot be changed by the

user. See “Regulatory information” on page 4 for specific sensitivity

values.

•Connect this detector only to a UL Listed control panel capable of

differentiating between alarm signals (fire, burglary, CO, etc.) and

providing distinct identification for each.

•To reduce the likelihood of nuisance alarms, ventilate

accommodation spaces when using household cleaning supplies

or similar contaminants. If a detector has been exposed to such

contaminants, test it promptly afterwards.

Symptoms of CO poisoning

The following symptoms related to CO poisoning should be discussed

with all occupants of the protected site.

Mild exposure: Slight headache, nausea, vomiting, fatigue, runny nose,

sore eyes (often described as “flu-like” symptoms).

Medium exposure: Severe throbbing headache, dizziness, drowsiness,

confusion, fast heart rate.

Extreme exposure: Unconsciousness, brain damage, convulsions,

cardiorespiratory failure, death.

Many cases of reported CO poisoning indicate that while victims are

aware they are not well, they become so disoriented that they are

unable to save themselves by either exiting the building or calling for

assistance. Young children and pets may be the first affected.

CO sources

The CO sensor in this detector is designed to detect carbon monoxide

gas from any source of combustion. It is not intended to detect fire,

smoke, or any other gas. Potential CO sources include fuel-fired

appliances (e.g., space heater, furnace, water heater, range, oven,

clothes dryer); other sources of combustion (e.g., kerosene-burning

stove or heater, or gas log fireplace); or internal combustion engines.

In addition, excessive exhaust spillage or reverse venting of fuel-

burning appliances can produce dangerous transient levels of CO. This

can be caused by external conditions:

•Wind direction, velocity, or a combination of both, including high

gusts of wind or insufficient draft in vent pipes

•Temperature inversions that can trap exhaust gases near the

ground

•Negative pressure differential resulting from the use of exhaust

fans

•Simultaneous operation of several fuel-burning appliances

competing for limited internal air

•Vent pipe connections vibrating loose from dryers, furnaces, or

water heaters

•Obstructions in vent pipes or unconventional vent pipe designs

which can amplify the above situations

•Poorly designed or maintained chimneys and/or vents

•Extended operation of unvented fossil fuel-burning devices (range,

oven, fireplace, etc.)

•Idling cars in an open or closed attached garage, or near the

premises

firealarmresources.com

2 / 4 P/N 3102527-EN • REV 001 • ISS 14SEP18

General limitations of CO detectors

This detector is designed to protect individuals from the acute affects

of CO exposure. It will not fully safeguard individuals with specific

medical conditions. People with special medical problems should

consider using specialized detection devices with less than 30 ppm

(parts per million) alarming capabilities. If in doubt, consult a medical

practitioner.

If the detector is in trouble or at the end of its life, it may not sense CO

and cannot be relied upon to monitor CO levels. Replace the detector

every ten years from the date of manufacture or when the control panel

indicates a sensor end-of-life condition, whichever comes first.

A detector installed outside a bedroom may not awaken a sleeper.

Normal noise due to stereos, television, etc. may also prevent the

detector from being heard if distance or closed or partly closed doors

muffle the sounder. This unit is not designed for the hearing impaired.

CO detectors are not a substitute for life safety. Though these

detectors will warn against increasing CO levels, we do not warrant or

imply in any way that they will protect lives from CO poisoning. They

should only be considered as an integral part of a comprehensive

safety program.

Detector locations

Selecting a suitable location is critical to the operation of CO detectors.

Figure 1: shows appropriate detector locations.

Install detectors according to applicable codes and standards. Place

wall-mounted detectors at least 5 ft. (1.5 m) up from the floor. For

ceiling mounted applications, place detectors at least 1 ft. (0.3 m) from

any wall. For combination detectors, follow the spacing requirements

for each sensor. Refer to the control panel’s application bulletin for the

sensor spacing requirements.

The recommended CO detector locations are:

•Outside each separate sleeping area in the immediate vicinity of

the bedrooms (including areas such as hotel rooms and dorm

rooms)

•On every occupiable level of a dwelling unit, including basements,

but excluding attics and crawl spaces

•Centrally located on every habitable level of the building and in

every HVAC zone based on an engineering evaluation considering

potential sources and migration of carbon monoxide

•On the ceiling in the same room as permanently installed fuel-

burning appliances

•In any area required by local building codes, legislation, or the

authority having jurisdiction

•In a suitable environment per the detector specifications (see

“Specifications” on page 4 for details)

•On a firm, permanent surface

Do not install the CO detector:

•Within 5 ft. (1.5 m) of any cooking appliance

•Within 10 ft. (3 m) of a fuel-burning appliance

•Near air conditioners, heating registers, or any other ventilation

source that may interfere with CO gas entering the detector

•Where furniture or draperies may obstruct the airflow

•In a recessed area

Figure 1: Recommended CO detector locations

Recommended CO detector location

Description

The model KIR-COD Intelligent CO Sensor is an intelligent device that

uses a CO sensor to detect carbon monoxide from any source of

combustion and analyzes the sensor data to determine when to initiate

a life safety CO alarm. It is not intended to detect fire, smoke, or any

other gas.

LED indicator. The LED indicator (see Figure 2) displays the following

states:

•Normal: Green LED indicator flashes, no action.

•Alarm/active: Red LED indicator flashes, evacuate the area.

Sensor end-of-life indicator. The detector signals a “COMMON

TRBL ACT”condition on the control panel when the CO sensor

reaches its end of life. Pressing the Details button on the control panel

displays “END OF LIFE ACT”providing verification that it is an end-of-

life trouble of the CO sensor. This trouble remains active until the

detector is replaced, even if the panel is reset.

Figure 2: KIR-COD features

(1) Self-locking tab

(2) LED indicator

firealarmresources.com

P/N 3102527-EN • REV 001 • ISS 14SEP18 3 / 4

Installation

Notes

•To ensure proper operation, store the detector within the

recommended ranges. Allow the detector to stabilize to room

temperature before applying power.

•The dust cover (supplied) must remain on the detector during

installation and be removed prior to commissioning and service.

The dust cover is not a substitute for removing the detector during

new construction or heavy remodeling.

•Do not install detectors until after final construction cleanup (unless

otherwise specified by the AHJ).

•Install per NFPA 720 Standard for the Installation of Carbon

Monoxide (CO) Detection and Warning Equipment, UL 2075

Standard for Gas and Vapor Detectors and Sensors, and

applicable codes.

To install the detector:

1. Install and wire the base as described on the installation sheet

supplied with the base.

2. Set the detector address. Refer to the panel technical reference

manual for a list of valid addresses. Use a screwdriver to adjust

the two rotary switches on the back of the detector.

(See Figure 3:) Set the left rotary switch (0 through 12) for the 10s

and 100s digit and the right rotary switch for the 0 through 9 digit.

3. Attach the detector to the base by rotating the detector clockwise

until it snaps into the locked position.

4. If required by the AHJ or local codes, affix the supplied CO

Warning Label (P/N 3303928) in proximity to the detector.

Figure 3: Setting detector address (address 52 shown)

(1) Insert a screwdriver here to set the address

Testing

Before testing, notify the proper authorities that the fire alarm system is

undergoing maintenance and will be temporarily out of service.

Test each sensor in the detector.

Note: If the CO sensor is programmed as an alarm point, it must

comply with the requirements of NFPA 720.

To perform an initial installation test:

1. Visually inspect each detector and verify that it is installed in the

correct location. Make sure that factors not apparent on the plans

do not adversely affect the detector.

2. Remove the detector from its base and verify that the proper

detector address, trouble signals, and messages are reported.

3. If wired for Class A operation, verify that the detector continues to

operate first with SLC_IN disconnected, and then with SLC_OUT

disconnected. (Refer to the installation sheet for the base.)

4. Place a momentary ground fault on the SLC circuit and verify

operation of the ground fault detection circuitry.

5. Perform a sensor function test, as described below.

To perform a CO sensor function test:

1. Use the fire alarm control panel to put the detector into accelerated

response mode. (Refer to the panel technical reference manual for

instructions.)

2. Activate the CO sensor using SDI LLC model Solo C6 CO aerosol

spray without covering the head, or using the Testifire detector

tester per the manufacturer’s instructions.

Maintenance

To ensure proper operation, plan maintenance (regular or selected) of

the detector in accordance with the AHJ and all applicable governing

laws, codes or standards. Refer to NFPA 720 Standard for the

Installation of Carbon Monoxide(CO) Detection and Warning

Equipment.

Refer to application bulletin 3102534-EN for additional information and

cleaning instructions.

CO sensor. The CO sensor has a 10 years life from the date of

manufacture or when the control panel indicates a sensor end-of-life

condition, whichever comes first.

23456

456 7 8901

TENS ONES

(1)

firealarmresources.com

4 / 4 P/N 3102527-EN • REV 001 • ISS 14SEP18

Specifications

Operating voltage

15.20 to 19.95 VDC

Current

Normal operating current

Alarm

51 µA

68 µA

Vibration level

10 to 35 Hz, with an amplitude of

0.01 in.

Compatible bases

Standard

Relay

Isolator

Audible

KI-SB, KI-SB4

KI-RB, KI-RB4

KI-IB, KI-IB4

KI-ABDT [1], KI-ABLT [1]

Compatible detector testers

Testifire 2000

Operating environment

Temperature

Relative humidity

32 to 120°F (0 to 49°C)

0 to 90% noncondensing

Storage temperature

−4 to 140°F (−20 to 60°C)

Environmental compensation

Automatic

[1] Required for those installations that must provide separate CO

(TC4) and fire (TC3) patterns from the sounder base. Refer to

FX-T3T4 installation sheet p/n 3102359-EN.

Regulatory information

UL CO alarm level

UL CO False

alarm level

70 ppm 60 to 240 minutes [1]

150 ppm 10 to 50 minutes [1]

400 ppm 4 to 15 minutes [1]

30 ppm 30 days[1]

70 ppm 60 minutes[1]

North American

standards

UL 2075

Note: This detector has been evaluated to the CO

alarm sensitivity limits of UL 2034.

FCC compliance

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation.

[1] Sensitivity per UL 2034

Contact information

For contact information, see www.kiddelifesafety.com.

firealarmresources.com

Andere Kidde Zubehör Handbücher

Kidde

Kidde Co120x Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung