KMC Controls NetSensor KMD-1261 Betriebsanleitung

Contents

Specifications ............................................................... 2

Network cable preparation ........................................... 6

Rough-in preparation ................................................... 6

Installing the NetSensor ................................................ 7

PC data port ................................................................. 8

Operation .................................................................... 9

Maintenance .............................................................. 10

Programming ............................................................. 11

Installation and

Operation Guide

NetSensor

KMD-1261 and KMD-1281

Motion, temperature and humidity

sensors

903-019-10

KMC Controls

Specifications

Display LCD, 4-character, 7-segment,

0.375 in. high. (temperature)

Compatibility KMD-5800 series controllers

KMD-7000 series controllers

BAC-5800 series BACnet controllers

BAC-7000 series BACnet controllers

Controller Connection

Connector type Six-wire RJ-12 modular jack

Cable type and length Up to 75 feet (22.9 meters) maximum;

conductors no smaller than 24 AWG

Power 5 volts DC supplied from the connected

controller

Mounting Surface mount directly to any flat

surface or to a 2 x 4 inch or 4 x 4 inch

handy-box. Mounting on a 4 x 4 inch

box requires a mounting backplate.

Weight 2.8 ounces (80 grams)

Material Light almond or white plastic

Accessories

Mounting backplate

Almond 4 x 4 inch HMO-1161

White 4 x 4 inch HMO-1161W

Gasket HPO-1161

Replacement Allen screws HPO-0044 (package of 10)

Network plenum cables with connectors

25 feet (7.6 meters) KMD-5690

50 feet (15.2 meters) KMD-5691

75 feet (22.9 meters) KMD-5692

NetSensor Installation and Operation

PC data port interfaces See “PC data port” on page 8.

Sensor Accuracy, KMD-1261

Type Thermistor

Accuracy ±0.36° F (±0.2° C)

Resistance 10,000at 77° F (25° C)

Operating range 48° to 96° F (8.8° to 35.5° C)

Sensor Accuracy, KMD-1281

Type CMOS

Humidity

Range 0 to 100% Relative humidity

Accuracy at 25°C ±2% from 10–90% Relative humidity

Response time Less than or equal to 4 seconds

Tempe r ature

Accuracy ±0.9° F (±0.5° C) Offset from

40 to 104° F

(4.4 to 40.0° C) Offset is adjusted

through configuration software

Resolution ±0.1°F (±0.1° C)

Operating range 36 to 120° F (2.2 to 48.8° C)

Response time 5 to 30 seconds

Environmental Limits

Operating Temperature 34° to 125° F (1.1 to 51.6° C)

Shipping –40° to 140° F (–40°C to 60° C)

Humidity 0 to 95% Relative humidity

non-condensing

KMC Controls

Dimensions

AB CDE F

3.25 in. 5.16 in. 2.58 in. 3.25 in. 0.87 in. 1.07 in.

83 mm 131 mm 66 mm 83 mm 22 mm 27 mm

NetSensor Installation and Operation

Motion sensor range 33 feet (10 meters)

Models KMD-1261 and KMD-1281 detect motion and change the

value of the auxiliary function.

• A value of -1 indicates motion

• A value of -2 indicates no motion

• A value of 0 or 1 indicates the auxiliary function is active.

The value of the auxiliary function will remain at 0 for approximately

30 seconds after power is applied to the NetSensor.

Models

Temperature only

Almond KMD-1261

White KMD-1261W

Temperature and humidity

Almond KMD-1281

White KMD-1281W

55°

10 m

32.8 ft

10 m

32.8 ft

0°

10 m

32.8 ft

10 m

32.8 ft

0°

46.5°

Top view Side view

KMC Controls

Network cable preparation

Connecting a NetSensor to a controller requires a six-wire cable with

RJ-12 connectors on each end. KMC plenum-rated preassembled

cables are recommended. Cables made to length must meet the

following requirements:

◆Cable length must be no longer than 75 feet (22.9 meters).

◆Cable conductors must be no smaller than #24 AWG.

◆Cable insulation must meet local building codes.

◆Connectors must be appropriate for the cable in use and are

installed following the connector manufacturers instructions.

Rough-in preparation

Caution

To prevent mounting screw heads from touching the circuit

board in the NetSensor, use only the mounting screws

supplied by KMC Controls. Using screws other than the

type supplied will damage the NetSensor.

Cable details

RJ-12

NetSensor Installation and Operation

Complete rough-in wiring at each sensor location prior to sensor

installation. This includes the following.

◆Routing the network cable from the NetSensor to a controller.

◆If required, installing the appropriate backplate. See Accessories

on page 2 for model numbers.

Installing the NetSensor

1. Turn the Allen screws in the base of the NetSensor clockwise

until they clear the cover. Swing the sensor away from the

mounting base to remove it.

2. Route the RJ-12 cable through the mounting base.

3. Fasten the mounting base directly to a 2 x 4 inch outlet box or a

backplate with the Allen screws toward the floor.

4. Insert the RJ-12 cable coming from the base into the NetSensor.

5. Place the top of the NetSensor over the top of the mounting base

and swing it down over the Allen screw brackets. Be careful not

to pinch any wiring.

6. Back the Allen screws out of the brackets until they engage the

NetSensor cover and hold it in place.

NetSensor mounting details

Mounting screws

Network

cable

Allen

screws

Mounting

base

Turn clockwise to

remove from base.

KMC Controls

PC data port

The NetSensor is equipped with a PC data port located at the bottom

of the NetSensor housing. This port provides a temporary connection

for setup or troubleshooting to either KMD Tier 2 or BACnet MS/TP

networks.

To use the port to connect to a computer, use one of the following

connection methods. The exact connection depends on the computer

and the operator workstation software (see also the instructions

included with those devices and software):

◆For a USB connection with either WinControl or BACstage, use a

KMD-5576 USB Communicator (see the illustration above).

◆For a serial port connection to BACstage, use a third-party

interface.

◆For serial port connection to WinControl, use a KMD-5559

CommTalk and KMD-5624 cable.

To use the PC data port:

1. Connect the keyed, flat end of the KMD-5624 NetSensor

interface cable to the port on the NetSensor. The KMD-5624

cable is included with the KMD-5576 but not the KMD-5559.

2. Connect the RJ-12 end of the cable to the interface device that

converts the EIA-485 signal from the NetSensor into a USB or

EIA-232 signal.

3. Connect the suitable cable from the interface device to the

computer’s serial or USB port. Install any required software and

configure the port as necessary.

NetSensor PC port location and USB connection

NetSensor Installation and Operation

Operation

The following sections describe the controls and indicators found on

the NetSensor.

Display The temperature display contains four 0.375-inch, 7-segment

LCD digits that are visible across a normal size office. The display

provides time, temperature and on the KMD-1281 humidity

readouts. Room temperature is displayed until either setpoint button

is pressed and then the display changes to setpoint mode.

Controls Models KMD-1261 and KMD-1281 include eight push

buttons; six of which (button 1 and buttons 3-7) are user

programmable. The actual operation of the programmable buttons

depend upon the program in the controller to which the NetSensor is

connected. See Programming on page 11.

The arrow buttons adjust the programmed values up or down. Values

can be changed for all programmed buttons except the setpoint as

follows:

1. Press the button for the desired function.

2. Adjust the value up or down.

Setpoint Pressing either the up or down arrow buttons changes

the display from room temperature mode to setpoint mode. Each

additional time a setpoint button is pressed and released changes the

setpoint up or down.

Auxiliary function These NetSensors do not have auxiliary wires

found on earlier models. Press buttons 5 and 7 together and then

press an up arrow or down arrow button to change the auxiliary

function.

NetSensor buttons

Setpoint

KMC Controls

Maintenance

Remove dust as necessary from holes in top and bottom. Clean the

display and motion sensor cover with a soft, damp cloth and mild

soap.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KMC Controls Zubehör Handbücher

KMC Controls

KMC Controls NetSensor KMD-1162 Betriebsanleitung

KMC Controls

KMC Controls STE-6014-10 Bedienungsanleitung

KMC Controls

KMC Controls STE-6014 Benutzerhandbuch

KMC Controls

KMC Controls SSS-1000 Series Bedienungsanleitung

KMC Controls

KMC Controls Conquest STE-90 Series Bedienungsanleitung

KMC Controls

KMC Controls STE-6010-10 Bedienungsanleitung

KMC Controls

KMC Controls STE-6014 Bedienungsanleitung

KMC Controls

KMC Controls SSS-1000 Series Bedienungsanleitung

KMC Controls

KMC Controls THE-1105 Bedienungsanleitung

KMC Controls

KMC Controls STE-6010 Benutzerhandbuch

KMC Controls

KMC Controls STW-6010 Bedienungsanleitung

KMC Controls

KMC Controls STW Series Bedienungsanleitung

KMC Controls

KMC Controls KMD-1183 Betriebsanleitung

KMC Controls

KMC Controls STE-1421 Bedienungsanleitung

KMC Controls

KMC Controls STE-8001 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung