KNX AQS/TH-UP Touch Leitfaden

KNX AQS/TH-UP Touch

Combined indoor sensor

Item numbers 70619 (black), 70620 (pure white)

Installation and Ad justment

1 Content

Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany

Sensor KNX AQS/TH-UP Touch • from ETS programme version 1.0

Status: 23.10.2018 • Technical changes and errors excepted.

1. Description ........................................................................................... 4

1.0.1. Scope of delivery .......................................................................................... 5

1.1. Technical specifications ........................................................................................... 5

1.1.1. Accuracy of the measurement ..................................................................... 6

2. Installation and commissioning ........................................................... 6

2.1. Installation notes ...................................................................................................... 6

2.2. Installation position .................................................................................................. 7

2.3. Composition ............................................................................................................. 8

2.3.1. Housing .......................................................................................................... 8

2.4. Assembly of the sensor ........................................................................................... 8

2.5. Notes on mounting and commissioning ................................................................ 8

3. Display and operation at the device .................................................... 9

3.1. Mode display and manual temperature controller ................................................ 9

3.2. Change ambient temperature with the buttons .................................................. 10

4. Transfer protocol ............................................................................... 12

4.1. List of all communications objects ....................................................................... 12

5. Parameter setting .............................................................................. 23

5.1. Behaviour on power failure/ restoration of power .............................................. 23

5.2. General settings ..................................................................................................... 23

5.3. Temperature value ................................................................................................. 23

5.4. Temperature threshold values .............................................................................. 24

5.4.1. Threshold value 1, 2, 3 ............................................................................... 24

5.4.1.1. Threshold value ............................................................................ 24

5.4.1.2. Switching output .......................................................................... 25

5.4.1.3. Block .............................................................................................. 26

5.5. Temperature PI control .......................................................................................... 26

5.5.0.1. General control ............................................................................. 26

5.5.1. General set point values ............................................................................. 28

5.5.1.1. Set point Comfort ......................................................................... 29

5.5.1.2. Standby setpoint ........................................................................... 30

5.5.1.3. Eco setpoint ................................................................................... 30

5.5.1.4. Setpoint values for frost/heat protection (building protection) 31

5.5.1.5. General control variables ............................................................. 31

5.5.2. Heating control level 1/2 ............................................................................. 32

5.5.3. Cooling control level 1/2 ............................................................................. 34

5.6. Humidity measurement ......................................................................................... 36

5.7. Humidity threshold values .................................................................................... 36

5.7.1. Threshold value 1, 2 ................................................................................... 37

5.7.1.1. Threshold value ............................................................................ 37

5.7.1.2. Switching output .......................................................................... 38

5.7.1.3. Block .............................................................................................. 38

5.8. Humidity PI control ................................................................................................ 39

2 Content

Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany

Sensor KNX AQS/TH-UP Touch • from ETS programme version 1.0

Status: 23.10.2018 • Technical changes and errors excepted.

5.8.0.1. General control ............................................................................. 39

5.8.0.2. Controller setpoint ........................................................................ 40

5.8.0.3. Dehumidification and/or humidification ..................................... 41

5.9. Dewpoint measurement ........................................................................................ 42

5.9.1. Cooling medium temp. monitoring ........................................................... 42

5.9.1.1. Threshold value ............................................................................ 42

5.9.1.2. Switching output .......................................................................... 43

5.9.1.3. Blocking ......................................................................................... 43

5.10.Absolute humidity ................................................................................................. 44

5.11.Comfort field .......................................................................................................... 45

5.12.CO2parameter settings ......................................................................................... 45

5.13.CO2 threshold values ............................................................................................ 46

5.13.1. Threshold value 1, 2, 3, 4 ........................................................................... 46

5.13.1.1.Threshold value ............................................................................ 46

5.13.1.2.Switching output .......................................................................... 47

5.13.1.3.Block .............................................................................................. 48

5.14.CO2 PI-control ........................................................................................................ 49

5.14.0.1.General control ............................................................................. 49

5.14.0.2.Controller setpoint ........................................................................ 49

5.14.0.3.Ventilation control ........................................................................ 50

5.15.Variable comparator .............................................................................................. 51

5.15.1. Control variable comparator 1/2 ................................................................ 51

5.16.Logic ........................................................................................................................ 52

5.16.0.1.AND logic ....................................................................................... 52

5.16.0.2.OR logic ......................................................................................... 52

5.16.1. AND logic 1-4 and OR logic outputs 1-4 ................................................... 52

5.16.1.1.Block .............................................................................................. 54

5.16.2. Connection inputs of the AND logic .......................................................... 54

5.16.3. Connection inputs of the OR logic ............................................................. 56

5.17.Display .................................................................................................................... 56

5.18.Pushbutton ............................................................................................................. 58

5.18.1. Pushbutton for temperature control ......................................................... 59

5.18.2. Pushbutton interface .................................................................................. 59

3 Clarification of signs

This manual is amended periodically and will be brought into line with new software

releases. The change status (software version and date) can be found in the contents footer.

If you have a device with a later software version, please check

www.elsner-elektronik.de in the menu area "Service" to find out whether a more up-to-

date version of the manual is available.

Clarification of signs used in this manual

Installation, inspection, commissioning and troubleshooting of the device

must only be carried out by a competent electrician.

Safety advice.

Safety advice for working on electrical connections, components,

etc.

DANGER! ... indicates an immediately hazardous situation which will lead to

death or severe injuries if it is not avoided.

WARNING! ... indicates a potentially hazardous situation which may lead to

death or severe injuries if it is not avoided.

CAUTION! ... indicates a potentially hazardous situation which may lead to

trivial or minor injuries if it is not avoided.

ATTENTION! ... indicates a situation which may lead to damage to property if it is

not avoided.

ETS In the ETS tables, the parameter default settings are marked by

underlining.

4 Description

Sensor KNX AQS/TH-UP Touch as of software 0.1.0 • Version: 23.10.2018 • Technical changes and errors excepted.

1. Description

The Sensor KNX AQS/TH-UP Touch measures CO2concentration, temperature and

humidity and calculates the dew point. The sensor can receive external measured

values via the bus and process them with the own data to overall values (mixed values,

e. g. room average). The KNX AQS/TH-UP Touch offers two push buttons that may

be used for changing the ambient temperature (target value), for switching between

operating modes or as free programmable bus push buttons.

The KNX AQS/TH-UP Touch provides switching outputs with adjustable threshold

values. The switching outputs and further communication objects can be linked by

AND and OR logic gates. Additionally, an integrated actuating variable comparator can

compare and output values that are received via communication objects.

Integrated PI controllers allows for control of a ventilation (depending on CO2

concentration and air humidity) and a heating/cooling system (depending on

temperature). The KNX AQS/TH-UP Touch can emit a warning to the bus as soon as

the area of optimum comfort (according to DIN 1946) is left.

The integrated display shows the own values and data received from the bus (e.g. date,

time). The device is completed with a frame of the switching series installed in the

building and thus merges with the interior.

Functions:

• Measurement of CO2concentration of the air, of temperature and air

humidity (absolute and relative), calculation of the dew point

•Mixed values from own measured values and external values (proportions

can be set in percentage)

•Display 1-3 rows (own values or values received from the bus) or display of

temperature control (see Mode display and manual temperature controller)

•2 push buttons. Configuration as bus push button or for changing ambient

temperature and switching between operating modes (see Change ambient

temperature with the buttons)

•PI controller for heating (one or two step) and cooling (one or two step)

depending on temperature. Control according to separate target values or

basic target temperature

•PI controller for ventilation depending on humidity and CO2concentration:

dehumidification/humidification (one step) or dehumidification (one or two

step)

•Threshold values can be adjusted per parameter or via communication

objects: 3 × temperature, 2 × humidity, 4 × CO2

•4 AND and 4 OR logic gates with each 4 inputs. Every switching incident as

well as 16 logic inputs in the form of communication objects, may be used as

inputs for the logic gates. The output of each gate may optionally be configured

as 1 bit or 2 x 8 bits

•2 actuating variable comparators for output of minimum, maximum or

average values. Each with 5 inputs (for values received via communication

objects)

5 Description

Sensor KNX AQS/TH-UP Touch as of software 0.1.0 • Version: 23.10.2018 • Technical changes and errors excepted.

Configuration is made using the KNX software ETS 5. The product file can be

downloaded from the ETS online catalogue and the Elsner Elektronik website on

www.elsner-elektronik.de in the “Service” menu.

1.0.1. Scope of delivery

• Housing with display

• Base plate

You will need in addition (not supplied):

• Socket Ø 60 mm, 42 mm deep

• Frame (for element 55 x 55 mm), suitable for the switching programme used in

the building

1.1. Technical specifications

Housing ABS plastic material

Colours • similar to RAL 9005 jet black

• similar to RAL 9010 pure white

Mounting In-wall (wall mounting in socket Ø60 mm, 42 mm

deep, resp. cavity wall socket for hole Ø68 mm)

Protection category IP 20

Dimensions Housing approx. 55 x 55 (W x H, mm), mounting depth

approx. 8 mm, base plate approx. 71 x 71 (W x H, mm)

Total weight approx. 55 g

Ambient temperature Operation 0…+50°C, storage -10…+60°C

Ambient air humidity max. 95% RH, avoid bedewing

Operating voltage KNX bus voltage

Bus current max. 20 mA

Data output KNX +/- bus terminal plug

BCU type Own micro controller

PEI type 0

Group addresses max. 254

Allocations max. 254

Communication objects 224

CO2 measurement range 300...5000 ppm

CO2resolution 1 ppm

CO2accuracy ± 50 ppm plus ± 3% of the measured value (Mind the

notes on Accuracy of the measurement)

Temperature measurement

range

0…+50°C

Temperature resolution 0.1°C

Temperature accuracy ± 0,5°C at 0…+50°C (Mind the notes on Accuracy of the

measurement)

6 Installation and commissioning

Sensor KNX AQS/TH-UP Touch as of software 0.1.0 • Version: 23.10.2018 • Technical changes and errors excepted.

The product conforms with the provisions of EU guidelines.

1.1.1. Accuracy of the measurement

Measurement variations from permanent sources of interference (see chapter

Installation position) can be corrected in the ETS in order to ensure the specified

accuracy of the sensor (offset).

To ensure a correct CO2measurement, the device must be installed in a windproof

socket.

When measuring temperature, the self-heating of the device is considered by the

electronics. The heating is compensated by the software.

2. Installation and commissioning

2.1. Installation notes

Installation, testing, operational start-up and troubleshooting should

only be performed by an electrician.

CAUTION!

Live voltage!

There are unprotected live components inside the device.

• National legal regulations are to be followed.

• Ensure that all lines to be assembled are free of voltage and take

precautions against accidental switching on.

• Do not use the device if it is damaged.

• Take the device or system out of service and secure it against

unintentional use, if it can be assumed, that risk-free operation is no

longer guaranteed.

The device is only to be used for its intended purpose. Any improper modification or

failure to follow the operating instructions voids any and all warranty and guarantee

claims.

After unpacking the device, check it immediately for possible mechanical damage. If it

has been damaged in transport, inform the supplier immediately.

Humidity measurement

range

0% RH …95% RH

Humidity resolution 0.1%

Humidity accuracy ±7,5% RH at 0...10% RH

±4,5% RH at 10...90% RH

±7,5% RH at 90...95% RH

Humidity drift ± 0.5% R.H. per year in normal air

7 Installation and commissioning

Sensor KNX AQS/TH-UP Touch as of software 0.1.0 • Version: 23.10.2018 • Technical changes and errors excepted.

The device may only be used as a fixed-site installation; that means only when

assembled and after conclusion of all installation and operational start-up tasks and

only in the surroundings designated for it.

Elsner Elektronik is not liable for any changes in norms and standards which may occur

after publication of these operating instructions.

2.2. Installation position

The Sensor KNX AQS/TH-UP Touch is made for wall mounting in a socket

(Ø 60 mm, 42 mm deep).

May be installed and operated in dry interior rooms only.

Avoid condensation.

When selecting an installation location, please ensure that the measurement results

are affected as little as possible by external influences. Possible sources of interference

include:

• Direct sunlight

• Drafts from windows and doors

• Draft from ducts which lead from other rooms or from the outside to the

junction box in which the sensor is mounted

• Warming or cooling of the building structure on which the sensor is mounted,

e.g. due to sunlight, heating or cold water pipes

• Connection lines and ducts which lead from warmer or colder areas to the

sensor

Measurement variations from permanent sources of interference can be corrected in

the ETS in order to ensure the specified accuracy of the sensor (offset).

To ensure a correct CO2measurement, the device must be installed in a windproof

socket.

Fig. 1: Sectional drawing.

The Sensor KNX AQS/TH-UP Touch fits into a standard

socket (Ø 60 mm, depth 42 mm).

The frame is not included!

8 Installation and commissioning

Sensor KNX AQS/TH-UP Touch as of software 0.1.0 • Version: 23.10.2018 • Technical changes and errors excepted.

2.3. Composition

2.3.1. Housing

2.4. Assembly of the sensor

First of all fit the windproof socket with connection. Also seal inlet pipes to avoid

infiltration.

Screw the base plate onto the socket and position the frame of the switching

programme. Connect the bus line +/- to the black-red plug.

Pin the housing with the notches on to the metal frame, so that device and frame are

fixed.

2.5. Notes on mounting and commissioning

Never expose the device to water (e.g. rain) or dust. This can damage the electronics.

You must not exceed a relative humidity of 95%. Avoid condensation.

After the bus voltage has been applied, the device will enter an initialisation phase

lasting a few seconds. During this phase no information can be received or sent via the

bus.

Fig. 2

1 Base plate

2 Openings for air circulation

3 Touch sensitive buttons

4 Catches

5 Programming LED (recessed)

6 Programming button (recessed) for teaching device

7 KNX terminal BUS +/-

Inhaltsverzeichnis

Andere KNX Zubehör Handbücher

KNX

KNX AQS-UP basic Leitfaden

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung