Koden KBG-3 Bedienungsanleitung
Declaration of Conformity
(As required by Article 6.3 of Directive 1999/5/EC-RTTE Directive)
Declares under his sole responsibility that the Marine GPS sensor module manufactured
by Koden Electronics Co., Ltd.
5278 Uenohara
Uenohara-Shi,
Yamanashi-Ken
409-0112, Japan
Telephone +81 554 20 5865 Telefax +81 554 20 5880
Intended for Worldwide use as a Marine GPS sensor for use aboard non-SOLAS vessels
and Identified by the type number KBG-3 to which this declaration refers
is in conformity with the EMC, Health and Safety standards of
EN60945
and complies with the essential requirements of Directive
1999/5/EC
Conformity assessment under Annex II of 1999/5/EC (internal production control) has
been undertaken.
Koden Electronics Co., Ltd.
5278 Uenohara, Uenohara-Shi
Yamanashi-Ken
409-0112, Japan
Telephone +81 554 20 5865
Telefax +81 554 20 5880
Signed ………………………………………
Kenichi Chiwaki
Manager / Quality Assurance Department
Dated ………………………………………
20 Jun. 2006
AMENDMENT HISTORY
KBG-3 INSTALLATION MANUAL
Doc No: 0092622632
No. Document No & Rev No. Revised Date
Y/M /D
Amendments
0 0092622632-00 2005/12/06 First issue
1 0092622632-01 2006/06/27 Chapter 5
2 0092622632-02 2008/09/22 Declaration
3 0092622632-03 2010/02/26 Chapter 5
4 0092622632-04 2013/06/06 Chapter 4
5 0092622632-05 2017/06/12 Chapter 1
6
7
8
9
10
11
12
13
14
15
Amendment policy
When any change is applied in the document, only the document number of the relevant sheet(s) and
cover sheet are modified and the rest of the sheets are not changed. The document number is shown in
the footer area, right or left bottom of each sheet.
○
c2005-2017 Koden Electronics Co., Ltd.All rights reserved.
No part of this publication may be reproduced, transmitted, translated in any form by any means without
the written permission of Koden Electronics Co., Ltd. The technical descriptions contained in this
publication are subject to change without notice. Koden assumes no responsibility for any errors,
incidentals or consequential damages caused by misinterpretation of the descriptions contained in this
publication.
- This page intentionally left blank.-
KGB-3 Preface
Installation Manual
0092622632-01 (1)
Preface
Safety Precautions
zBe Sure to "Disconnect" Inboard Power Supply
It is still possible to receive an electric shock caused by unintentionally switching on
the power supply during maintenance work. To prevent this from happening, be sure
to disconnect the inboard power supply and the power supply switch of equipment.
Place a notice "Men working" near the power supply switch of equipment to ensure
safety.
zBe Careful about Dust
Dust can cause temporarily the respiratory diseases. While cleaning inside of
equipment, be careful not to inhale dust. It is advisable to wear a safety mask etc.
zTake Countermeasures against Static Electricity
Carpets laid on the floor and synthetic fiber clothes can generate static electricity, and
can damage the electronic parts on the printed circuit boards. Take appropriate
countermeasures against static electricity before handling the printed circuit boards.
Preface KBG-3
Installation Manual
(2) 0092622632-01
Symbols used in this installation manual
The following symbols are used in this installation manual. You are requested to be fully aware of
the meaning of each symbol before carrying out maintenance and check.
Alarm mark
Caution mark
Prohibition mark
To handle the equipment ignoring this sign may lead to injury to
the human body or damage to the equipment.
Warning
This sign indicates that a specified action is prohibited. The
prohibited action will be shown in the vicinity of the mark.
To handle the equipment ignoring this sign may lead to a
malfunction or a failure of the equipment.
Caution
KGB-3 Preface
Installation Manual
0092622632-01 (3)
How to use this installation manual
Scope
This installation manual contains necessary information about installation and inboard
maintenance of the DGPS sensor KBG-3.
Structure
To ensure quick reference of necessary information in this installation manual, the
whole structure is divided into chapters according to the contents. The contents
contained in each chapter are as follows.
Chapter 1: Overview
-About GPS
-About DGPS, SBAS
-Equipment outline
-Applicable standard
-Equipment interconnection diagram
Chapter 2: Equipment composition
-Standard equipment composition list
Chapter 3: Equipment specifications
-Specifications
-Serial data
-Power supply specifications
-Environment conditions
-External dimensions and weight
Chapter 4: Installation
-Installation precautions
-Unpacking and inspection of the goods
-Selection of the installation site
-Installation method
Preface KBG-3
Installation Manual
(4) 0092622632-01
Chapter 5: Technical references
-Details of input/output data
-Cable connections and connector pinouts
-List of geodetic systems
-Table of DGPS reference stations
Andere Handbücher für KBG-3
1
Inhaltsverzeichnis
Andere Koden Zubehör Handbücher
