Kohler K-20195 Montageanleitung

Installation and Care Guide

Vanity

K-20195

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

1304474-2-A

Tools and Materials

Before You Begin

CAUTION: Risk of property damage. Select 250 lb (113.4

kg) load bearing 5/16″lag bolts with a length to clear

obstacles in the wall and 5/16″washers. Calculate proper lag

bolt length by adding the following: 1-1/2″(38 mm) backing

material + wallboard thickness + back rail thickness.

IMPORTANT! Risk of property damage. Use care when moving

the cabinet to avoid impacting, sliding, or side-loading the legs.

IMPORTANT! Risk of product damage. Do not modify the vanity.

Doing so will compromise structural stability.

NOTICE: Siliconized acrylic caulk must be used to secure the

bathroom sink to the vanity. Do not use 100% silicone sealant which

will damage the ﬁnish of the vanity.

NOTICE: To avoid the risk of product damage, the ﬁnished wall

must be straight and plumb. If the ﬁnished wall is not straight and

plumb, the vanity will not be properly supported and will cause

misalignment of the sink and door.

Observe all local plumbing and building codes.

Provide 2x6 backing material behind the ﬁnished wall to properly

support the vanity.

Siliconized Acrylic

Caulk

Plus:

• 5/16" Lag Bolts and Washers

• Pad

• 2x6s

• Common Plumbing and Woodworking

Tools and Materials

1304474-2-A 2 Kohler Co.

1. Prepare the Site

NOTICE: If the K-20199 bridge cabinet will also be installed, extend

the backing material a minimum of 12″(305 mm) beyond the width

of the vanity on the side where the bridge will be installed.

NOTICE: To properly secure the vanity, the top of the required 2x6

backing material must be 32-1/2″(826 mm) from the ﬁnished ﬂoor.

Measure and mark 32-1/2″(826 mm) up from the ﬁnished ﬂoor.

This will be the height from the ﬁnished ﬂoor to the top of the

2x6 backing material.

Ensure there are no obstructions in the wall (such as wiring or

plumbing) from the marked height down to the ﬂoor. If there are

obstructions, select another area to install the vanity.

NOTICE: Extend the backing material beyond the width of the

vanity to the nearest stud to ensure proper support for the vanity.

Front-notch the studs 1-1/2″(38 mm) to ensure the 2x6 backing

material is ﬂush against the studs.

Secure the 2x6 backing material to the studs with framing nails.

Rough-in the water supply and drain lines.

NOTICE: To avoid the risk of product damage, the ﬁnished wall

must be straight and plumb. If the ﬁnished wall is not straight and

plumb, the vanity will not be properly supported and will cause

misalignment of the sink and door.

32-1/2"

(826 mm)

2x6 Backing Material

Kohler Co. 3 1304474-2-A

Prepare the Site (cont.)

Complete the ﬁnished wall. Make sure the ﬁnished wall is

straight and plumb, and the ﬂoor is ﬂat and perpendicular to the

ﬁnished wall.

1304474-2-A 4 Kohler Co.

2. Install the Legs

NOTE: To protect the ﬁnished surface of the vanity, perform

assembly tasks on a ﬂat, padded work surface.

Position the vanity on its side on a ﬂat, padded surface.

Attach the Legs

Secure each leg assembly using two #8 x 1″panhead screws, lock

washers, and ﬂat washers.

Kohler Co. 5 1304474-2-A

3. Secure the Vanity

CAUTION: Risk of personal injury. Select 250 lb (113.4 kg)

load bearing 5/16″lag bolts with a length to clear obstacles

in the wall and 5/16″washers. Calculate the proper lag bolt

length by adding the following: 1-1/2″(38 mm) backing

material, plus the wallboard thickness, plus the back rail

thickness.

IMPORTANT! Risk of product damage. The vanity is heavy and

cumbersome to move. Obtain sufficient help to lift or move the

vanity to avoid impacting, sliding, or side-loading the legs.

Position and Level

With assistance, lift and place the vanity in position against the

ﬁnished wall. Do not drag the vanity into position.

Verify the vanity is level and the back rail is plumb against the

wall. If necessary turn the leveler(s) to adjust the unit.

Using a 1/4″drill bit, drill pilot holes through the back rail and

the ﬁnished wall. Verify the pilot holes are positioned to ensure

the lag bolts will engage the 2x6 backing material.

Secure

Secure the vanity to the wall with two 5/16″lag bolts and

washers (not provided).

Washer

Lag Bolt

Leveler

Finished

Pilot Hole

1304474-2-A 6 Kohler Co.

4. Install the Bathroom Sink

CAUTION: Risk of personal injury. Vitreous china sinks are

very heavy. Get help lifting and aligning the sink.

Install the faucet and drain to the sink. Refer to the faucet and

drain manufacturer’s installation instructions.

NOTICE: Siliconized acrylic caulk must be used to secure the sink

to the vanity. Do not use 100% silicone sealant, which will damage

the vanity ﬁnish.

Apply a 1/4″(6 mm) continuous bead of siliconized acrylic caulk

around the top of the vanity, as illustrated.

NOTE: The sink is properly positioned when the back edge of the

sink is ﬂush against the ﬁnished wall, and the overhang on the left,

right, and front of the sink is the same.

With assistance, lift and properly position the sink on top of the

vanity.

Immediately wipe away any excess caulk that contacts the vanity.

Apply a 1/8″(3 mm) bead of siliconized acrylic caulk along the

top edge of the sink where the sink contacts the ﬁnished wall.

Kohler Co. 7 1304474-2-A

5. Complete the Installation

NOTICE: Ensure that the knob location you choose will provide

unobstructed clearance when opening and closing the door.

Select and mark the desired knob location on the door.

Use a 3/16″bit to drill the marked hole location.

From the back side of the door, insert the screw through the hole.

Thread the knob onto the screw. Securely hand-tighten.

Screw

Knob

1304474-2-A 8 Kohler Co.

6. Reinstall the Door

NOTICE: The door on this vanity was pre-installed by the

manufacturer. Follow these steps to reinstall the door if it has been

removed for any reason.

NOTE: To ease installation, get assistance supporting the door.

Align the hinge hooks with the cup of the top bracket.

Slide the hinge onto the top bracket.

Clip the hinge onto the bracket to secure.

Repeat for the lower hinge.

Hook

Bracket

Cup

Kohler Co. 9 1304474-2-A

7. Adjust the Door

Adjustment

Refer to the illustration and note the screwdriver location for the

desired adjustment.

Removal

Apply slight leverage to the door with one hand to keep the door

in the full open position.

Press the clip to release the hinge from its bracket.

Move the door forward to slide the hinges off the brackets.

Care and Cleaning

For best results, keep the following in mind when caring for your

KOHLER product:

Vitreous China and Fireclay

•Use a mild detergent such as liquid dishwashing soap and warm

water for cleaning. Do not use abrasive cleaners that may scratch

or dull the surface.

•Carefully read the cleaner product label to ensure the cleaner is

safe for use on the material.

•Always test your cleaning solution on an inconspicuous area

before applying to the entire surface.

•Do not allow cleaners to sit or soak on the surface.

Adjustments

Side

Depth Height

Bracket

Clip

1304474-2-A 10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Inneneinrichtung Handbücher

Kohler

Kohler CL Series Bedienungsanleitung

Kohler

Kohler Jacob Delafon Idol Bedienungsanleitung

Kohler

Kohler K-23111T Bedienungsanleitung

Kohler

Kohler Kathryn K-2318 Bedienungsanleitung

Kohler

Kohler K-99003-TLC Montageanleitung

Kohler

Kohler K-2412 Montageanleitung

Kohler

Kohler K-2527 Montageanleitung

Kohler

Kohler Vanity K-2435 Bedienungsanleitung

Kohler

Kohler K-99003T-R Bedienungsanleitung

Kohler

Kohler AMERISSIC K-99073T Bedienungsanleitung

Kohler

Kohler Englefield 1141301 Bedienungsanleitung

Kohler

Kohler Top Art K-14041 Bedienungsanleitung

Kohler

Kohler Purist 1011420-2-B Bedienungsanleitung

Kohler

Kohler K-45764T Bedienungsanleitung

Kohler

Kohler K-2461 Bedienungsanleitung

Kohler

Kohler K-2659 Montageanleitung

Kohler

Kohler K-2451 Montageanleitung

Kohler

Kohler M MODULAR Bedienungsanleitung

Kohler

Kohler K-96106X-L Montageanleitung

Kohler

Kohler K-2732 Montageanleitung

Kohler

Kohler K-1082 Montageanleitung

Kohler

Kohler Archer K-2449 Bedienungsanleitung

Kohler

Kohler K-3082 Bedienungsanleitung

Kohler

Kohler Kathryn K-3020 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung