Kohler Vanity K-2604 Montageanleitung

Installation and Care Guide

Vanity

Français, page ″Français-1″

Español, página ″Español-1″

K-2604

1207226-2-A

Tools

Important Information

CAUTION: Risk of property damage. Do not modify the

vanity. Doing so will compromise structural stability and may

cause property damage.

CAUTION: Risk of property damage. Use care when

moving the vanity to avoid impacting, sliding, or

side-loading the legs.

CAUTION: Risk of property damage. Select 250 lb (113.4

kg) load bearing 5/16″lag bolts with a length to clear

obstacles in the wall and 5/16″washers. Calculate proper lag

bolt length by adding the following: 1-1/2″(38 mm) backing

material + wallboard thickness + back rail thickness.

NOTICE: Siliconized acrylic caulk must be used to secure the sink

to the vanity. Do not use 100% silicone sealant which will damage

the ﬁnish of the vanity.

NOTICE: The ﬁnished wall must be straight and plumb to ensure

proper support of the vanity and alignment of the sink and door.

Observe all local plumbing and building codes.

Provide 2x6 backing material behind the ﬁnished wall to properly

support the vanity.

Plus:

• Wood Screws

• 2x6s

• 5/16" Lag Bolts and Washers

[Min 250 lb (113.4 kg) Load Bearing]

• Socket Wrenches

• Siliconized Acrylic Caulk

1207226-2-A 2 Kohler Co.

1. Prepare the Site

NOTICE: If the K-2607 bridge cabinet will also be installed, extend

the backing material a minimum of 12″(305 mm) beyond the width

of the vanity on the side where the bridge will be installed.

NOTICE: To properly secure the vanity, the top of the required 2x6

backing material must be 32-1/2″(826 mm) from the ﬁnished ﬂoor.

Measure and mark 32-1/2″(826 mm) up from the ﬁnished ﬂoor.

This will be the height from the ﬁnished ﬂoor to the top of the

2x6 backing material.

Ensure there are no obstructions in the wall (such as wiring or

plumbing) from the marked height down to the ﬂoor. If there are

obstructions, select another area to install the vanity.

NOTICE: Extend the backing material beyond the width of the

vanity to the nearest stud to ensure proper support for the vanity.

Front-notch the studs 1-1/2″(38 mm) to ensure the 2x6 backing

material is ﬂush against the studs.

Secure the 2x6 backing material to the studs with framing nails.

Rough-in the water supply and drain lines into the rough-in

plumbing area of the vanity.

NOTICE: The ﬁnished wall must be straight and plumb to ensure

proper support of the vanity and alignment of the sink and door.

2x6

Backing

Material

32-1/2" (826 mm)

Kohler Co. 3 1207226-2-A

Prepare the Site (cont.)

Complete the ﬁnished wall. Make sure the ﬁnished wall is

straight and plumb, and the ﬂoor is ﬂat and perpendicular to the

ﬁnished wall.

1207226-2-A 4 Kohler Co.

2. Secure the Vanity

CAUTION: Risk of property damage. Use care when

moving the vanity to avoid impacting, sliding, or

side-loading the legs.

CAUTION: Risk of property damage. Select 250 lb (113.4

kg) load bearing 5/16″lag bolts with a length that can safely

clear obstacles in the wall and 5/16″washers. Calculate the

proper length of the lag bolts by adding the following: 1-1/2″

(38 mm) backing material + wallboard thickness + back rail

thickness.

With assistance, lift and place the vanity in position against the

ﬁnished wall. Do not drag the vanity into position.

Verify the vanity is level and the back rail is plumb against the

wall. If necessary, turn the leveler(s) to adjust the unit.

Using a 1/4″drill bit, drill two pilot holes through the back rail

and the ﬁnished wall. Verify the pilot holes are positioned to

ensure the lag bolts will engage the 2x6 backing material.

Secure the vanity to the ﬁnished wall with two 5/16″lag bolts

and washers (not provided).

Pilot Hole Finished Wall

Leveler

Washer

Lag Bolt

Back Rail

Kohler Co. 5 1207226-2-A

3. Install the Bathroom Sink

CAUTION: Risk of personal injury. Vitreous china sinks are

very heavy. Get help lifting and aligning the sink.

Install the faucet (if applicable) and drain to the sink. Refer to the

faucet and drain manufacturer’s installation instructions.

NOTICE: Siliconized acrylic caulk must be used to secure the sink

to the vanity. Do not use 100% silicone sealant which will damage

the vanity ﬁnish.

Run a 1/4″(6 mm) continuous bead of siliconized acrylic caulk

around the top of the vanity, as illustrated.

NOTE: The sink is properly positioned when: (1) the back edge of

the sink is ﬂush against the ﬁnished wall and (2) the overhang on

the left, right, and front side of the sink is equal on each side of the

vanity.

With assistance, lift and properly position the sink on top of the

vanity.

Immediately wipe away any excess caulk that contacts the vanity.

Run a 1/8″(3 mm) bead of siliconized acrylic caulk along the top

edge of the sink where it contacts the ﬁnished wall.

1207226-2-A 6 Kohler Co.

4. Install the Door

NOTE: To ease installation, get assistance supporting the door.

NOTE: The vanity comes with hinges installed on the inside left. To

reverse door swing, use the included template (1181754-7) to mount

brackets to the opposite side of the vanity.

Align the hinge hooks with the cup of the top bracket.

Slide the hinge onto the top bracket.

Clip the hinge onto the bracket to secure.

Repeat for the lower hinge.

Hook

Bracket

Cup

Kohler Co. 7 1207226-2-A

5. Complete the Installation

Install the Door Knob

From the back side of the door, insert the screw through the

predrilled hole.

Thread the knob onto the screw. Tighten securely.

Install the Bridge Cabinet (Optional)

Refer to the installation instructions packed with the K-2607

bridge cabinet.

Knob

Screw

1207226-2-A 8 Kohler Co.

Door Adjustments

Adjustment

Refer to the illustration and note the screwdriver location for the

desired adjustment.

Removal

Apply a small amount of leverage to the door with one hand to

keep the door in the full open position.

Press the clip to release the hinge from its bracket.

Move the door forward to slide the hinges off the brackets.

Care and Cleaning

For best results, keep the following in mind when caring for your

KOHLER product:

Vitreous China and Fireclay

•Use a mild detergent such as liquid dishwashing soap and warm

water for cleaning. Do not use abrasive cleaners that may scratch

or dull the surface.

•Carefully read the cleaner product label to ensure the cleaner is

safe for use on the material.

•Always test your cleaning solution on an inconspicuous area

before applying to the entire surface.

•Do not allow cleaners to sit or soak on the surface.

Adjustments

Side

Depth

Height

Bracket

Clip

Kohler Co. 9 1207226-2-A

Care and Cleaning (cont.)

•Wipe surfaces clean and rinse completely with water immediately

after cleaner application. Rinse and dry any overspray that lands

on nearby surfaces.

•Use a soft, dampened sponge or cloth. Never use an abrasive

material such as a brush or scouring pad to clean surfaces.

Wood Surfaces

•As with any smooth surface, avoid using abrasive cleaners as

they will scratch the surface. Wipe the wood surface regularly to

prevent buildup of soap and scum.

•To protect against scratches, use felt, leather, or cork under all

items placed on the wood surface. To conceal scratches, a

touch-up marker is available for order. Contact a Kohler

distributor or call 1-800-4-KOHLER for ordering information.

•Do not expose wood furniture to direct sunlight, drying heat

sources, or dampness.

•Dust frequently with a soft cloth in the direction of the grain. Use

only products speciﬁcally made for cleaning wood. Avoid using

oily polishes or waxes, or products containing silicone. Blot spills

immediately with a soft, damp cloth.

•Every six months, remove soil buildup by rubbing with a soft

cloth dampened in a 50/50 solution of warm water and an

ammonia-free detergent. Wipe clean with a cloth dampened in

warm water, then wipe dry.

For detailed cleaning information and products to consider, visit

www.kohler.com/clean. To order Care & Cleaning information, call

1-800-456-4537.

Warranty

ONE-YEAR LIMITED WARRANTY

KOHLER plumbing products are warranted to be free of defects in

material and workmanship for one year from date of installation.

Kohler Co. will, at its election, repair, replace or make appropriate

adjustment where Kohler Co. inspection discloses any such defects

occurring in normal usage within one (1) year after installation. Kohler

Co. is not responsible for removal or installation costs. Use of in-tank

toilet cleaners will void the warranty.

To obtain warranty service contact Kohler Co. either through your

1207226-2-A 10 Kohler Co.

Andere Handbücher für Vanity K-2604

Inhaltsverzeichnis

Sprachen:

Andere Kohler Inneneinrichtung Handbücher

Kohler

Kohler Stillness 14388T Bedienungsanleitung

Kohler

Kohler K-2463 Bedienungsanleitung

Kohler

Kohler FLEXISPACE 2.0 K-23790T Bedienungsanleitung

Kohler

Kohler K-96106X-L Montageanleitung

Kohler

Kohler K-3082 Bedienungsanleitung

Kohler

Kohler FAIRFIELD K-72490T Bedienungsanleitung

Kohler

Kohler K-8211 Montageanleitung

Kohler

Kohler K-CB-CLW2030DAW Bedienungsanleitung

Kohler

Kohler K-2962 Montageanleitung

Kohler

Kohler Conceal K-2970 Montageanleitung

Kohler

Kohler Kathryn K-3020 Bedienungsanleitung

Kohler

Kohler ALEUTIAN K-24203T Bedienungsanleitung

Kohler

Kohler K-3082 Montageanleitung

Kohler

Kohler 97631-G9 Montageanleitung

Kohler

Kohler Bancroft 2461-F2 Montageanleitung

Kohler

Kohler K-2684 Montageanleitung

Kohler

Kohler K-9330 Montageanleitung

Kohler

Kohler Englefield Valencia Elite Bedienungsanleitung

Kohler

Kohler VEIL K-21800T-X Bedienungsanleitung

Kohler

Kohler K-2684 Montageanleitung

Kohler

Kohler Jacob Delafon Idol Bedienungsanleitung

Kohler

Kohler K-2967 Montageanleitung

Kohler

Kohler K-2412 Montageanleitung

Kohler

Kohler TRESHAM K-45980T-L Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung