Kohler K-10217 Bedienungsanleitung

Installation Guide

Centerset Lavatory Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-10217

1056603-2-A

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

IMPORTANT! Plumbers putty is not needed to install this faucet.

The base of the faucet acts as a water barrier.

Observe all local plumbing and building codes.

Shut off the main water supply.

Inspect the supply tubing for damage. Replace as necessary.

Clean the lavatory surface to remove any grease, oil, or debris.

This faucet is for use on a single-hole lavatory.

For new installations, install the faucet and drain to the lavatory

before installing the lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Adjustable

Wrench Thread

Sealant Plumbers

Putty

Hex

Wrench

1056603-2-A 2 Kohler Co.

1. Install the Faucet

IMPORTANT! Plumbers putty is not needed to install this faucet.

The base of the faucet acts as a water barrier.

Insert the supply hoses and stud of the faucet through the center

hole of the lavatory.

Position the base of the faucet ﬂush against the center hole of the

lavatory.

From underneath the lavatory, slide the bracket and washer onto

the stud.

Thread the nut onto the stud.

Tighten the nut securely against the bracket to secure the faucet

into place.

Bracket

Washer

Nut

Lavatory

Stud Supply Hoses

Kohler Co. 3 1056603-2-A

2. Install the Click Drain

CAUTION: Risk of product damage. Never pull on the drain

cap to open the drain. Press and release the drain cap once to

close it. Press and release it again to open it.

Remove the seal from the body.

Apply a 1/2″(1.3 cm) diameter ring of plumbers putty or other

sealant around the underside of the body according to the putty

manufacturer’s instructions.

Insert the body into the ﬁxture drain hole.

Attach the rubber washer (tapered side up) to the body.

Install the ﬂat washer over the threads of the body.

Partially thread the nut onto the body. Do not tighten at this time.

Orient the ″KOHLER″logo as desired. Adjustment is not possible

after ﬁnal assembly.

Wrench-tighten the nut.

Apply sealant tape to the top of the tailpiece threads before

screwing it into the body.

Connect the tailpiece to the body.

Remove any excess putty or sealant.

Rubber Washer

Lavatory

Tailpiece

Nut

Body

Flat Washer

Apply plumbers

putty.

1056603-2-A 4 Kohler Co.

3. Connect the Supplies

If the lavatory is not installed, install it at this time. Follow the

lavatory manufacturer’s instructions.

NOTE: Connect the supply hose marked with a blue dot to the cold

supply.

Connect the supply hose marked with a blue dot to the cold

supply.

Connect the remaining supply hose to the hot supply.

Tighten the connections with an adjustable wrench.

Supply

Stop

Supply

Hose

Kohler Co. 5 1056603-2-A

4. Installation Checkout

Connect the drain tailpiece into the P-trap.

Remove the aerator from the faucet spout.

Open the drain.

Turn on the main water supply and check for leaks. Repair as

needed.

Lift and rotate the faucet handle to the full hot position, then the

full cold position. Run water through the spout for about one

minute to remove any debris. Check for leaks and repair as

needed.

Push the lever handle down to close the water supplies, then

reinstall the aerator.

Aerator

Faucet Spout

1056603-2-A 6 Kohler Co.

5. Optional Temperature Limiting Adjustment

Carefully pry the plug button off of the lever handle with a small

ﬂat-blade screwdriver.

Loosen the setscrew with a hex wrench, then remove the lever

handle.

Note the position of the locking ring relative to the inner geared

ring.

NOTE: To avoid damage to the locking ring during removal, pry

each side of the locking ring off the inner geared ring with an equal

and even technique.

Gradually pry each side of the locking ring up off of the inner

geared ring and onto the valve stem with a ﬂat-blade screwdriver.

Rotate the locking ring clockwise to increase temperature, or

counterclockwise to decrease temperature.

Align the geared teeth, then slide the locking ring down until

ﬂush against the inner geared ring.

Reinstall the lever handle.

Test the temperature setting. Repeat the above steps, if needed.

Retighten the setscrew.

Press the plug button into place.

Setscrew

Plug Button Handle

Inner Geared

Ring

Locking Ring

Inner Geared

Ring

Kohler Co. 7 1056603-2-A

Guide de l’installation

Robinet de lavabo à petit entraxe

Outils et matériels

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de performance. Nos numéros de téléphone

et notre adresse du site internet sont au verso. Merci encore d’avoir

choisi la compagnie Kohler.

Avant de commencer

IMPORTANT ! Du mastic de plombier n’est pas nécessaire pour

installer ce robinet. La base du robinet sert de barrière d’eau.

Respecter tous les codes de plomberie et de bâtiment locaux.

Couper l’alimentation d’eau principale.

Inspecter si la tuyauterie d’alimentation est endommagée.

Remplacer si nécessaire.

Nettoyer la surface du lavabo pour éliminer toute graisse, huile

ou débris.

Ce robinet est conçu pour des lavabos à un oriﬁce.

Cléàmolette Joint

d'étanchéité

pourfiletage Masticde

plombier

Clé

hexagonale

Kohler Co. Français-1 1056603-2-A

Avant de commencer (cont.)

Pour de nouvelles installations, installer le robinet et le drain au

lavabo avant d’installer celui-ci.

Kohler Co. se réserve le droit d’apporter toutes modiﬁcations au

design des robinets et ceci sans préavis, comme spéciﬁé dans le

catalogue des prix.

Kohler Co. Français-2 1056603-2-A

1. Installer le robinet

IMPORTANT ! Du mastic de plombier n’est pas nécessaire pour

installer ce robinet. La base du robinet sert de barrière d’eau.

Insérer les tuyaux d’alimentation et le manche du robinet dans

l’oriﬁce central du lavabo.

Positionner la base du robinet à égalité contre l’oriﬁce central du

lavabo.

À partir du dessous du lavabo, glisser le support et la rondelle

sur le montant.

Serrer l’écrou sur le manche.

Serrer fermement l’écrou contre le support pour sécuriser le

robinet en place.

Support

Rondelle

Écrou

Lavabo

Montant Flexibles d'alimentation

1056603-2-A Français-3 Kohler Co.

Andere Handbücher für K-10217

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-T10585 Bedienungsanleitung

Kohler

Kohler K-7397 Montageanleitung

Kohler

Kohler K-14424 Bedienungsanleitung

Kohler

Kohler K-9132 Bedienungsanleitung

Kohler

Kohler K-1188BR Bedienungsanleitung

Kohler

Kohler K-4986X Montageanleitung

Kohler

Kohler 13EOZD Bedienungsanleitung

Kohler

Kohler 31138T-4 Bedienungsanleitung

Kohler

Kohler Supply K-13724 Bedienungsanleitung

Kohler

Kohler Rapport K-1496-H2 Bedienungsanleitung

Kohler

Kohler K-T13141 Montageanleitung

Kohler

Kohler TOUCHLESS 32323T-4 Bedienungsanleitung

Kohler

Kohler K-10215 Montageanleitung

Kohler

Kohler K-4108BR Bedienungsanleitung

Kohler

Kohler Memoirs Stately 3 Hole Basin Mixer Bedienungsanleitung

Kohler

Kohler K-7163 Bedienungsanleitung

Kohler

Kohler 99721T-4 Bedienungsanleitung

Kohler

Kohler K-2804 Bedienungsanleitung

Kohler

Kohler STRAYT 37337T-B4 Bedienungsanleitung

Kohler

Kohler 16316-4FP Bedienungsanleitung

Kohler

Kohler K-2331 Montageanleitung

Kohler

Kohler 72282T-4 Service-Handbuch

Kohler

Kohler K-310 Montageanleitung

Kohler

Kohler K-11660 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung