Kohler K-10268 Bedienungsanleitung

Installation Guide

Centerset Lavatory Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-10268, K-10270, K-10271

1018258-2-F

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Carefully inspect the waste and supply tubing for any sign of

damage.

For new installations, install the faucet and drain to the lavatory

before installing the lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Pliers

#2 Phillips

Screwdriver

3/16" Hex

Wrench

Thread

Sealant

Pipe

Sealant

Plumbers

Putty

Adjustable Wrench

1018258-2-F 2 Kohler Co.

1. Faucet Installation

Clean the lavatory surface to remove any grease, oil, or debris.

Using a #2 Phillips screwdriver or 3/16″hex wrench, tighten the

faucet through the lift rod hole.

Phillips

Screwdriver

Faucet

Body

Hex

Wrench

Kohler Co. 3 1018258-2-F

2. Choose Drain Type

Refer to the illustrations above to determine the drain style you

received with your faucet.

Please follow the instructions for your drain style.

Style A Drain Style B Drain

1018258-2-F 4 Kohler Co.

3. Drain Installation-Style A

Remove the protective material from the ﬂange.

Wrap the bottom 2/3 of the ﬂange threads with three layers of

sealant tape.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Insert the ﬂange into the ﬁxture drain hole.

Assemble the gasket (tapered side up) and washer to the ﬂange

and partially thread the nut to the ﬂange. Do not fully tighten the

nut at this time.

Install the body washer and drain body with the seal hole facing

the back of the ﬁxture and securely tighten the nut. Use care to

avoid scratching the ﬁnish.

Remove any excess putty or sealant.

Insert the stopper into the ﬂange.

Insert the seal into the seal hole on the body.

Seal

Stopper

Lavatory

Screw

Spring

Clip Gasket

NutNut

Link

Rod Seal

Flange

Apply plumbers

putty.

Apply 3 layers of

sealant tape to

bottom 2/3.

Washer

Body Washer

Drain Body

Kohler Co. 5 1018258-2-F

4. Complete Drain Installation-Style A

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper. Secure

with the body nut.

Remove and adjust the stopper so it lifts about 3/8″(1 cm) when

opened. To adjust, loosen the stopper nut and shorten or lengthen

the stopper as needed. Tighten the stopper nut.

Apply three layers of thread tape and a small bead of pipe

sealant to the tailpiece threads.

Thread the tailpiece to the body and tighten securely.

Slide one end of the clip onto the rod. Slide the link onto the rod

with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the faucet and then into the

hole in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

above the lift rod hole.

Body Nut

Stopper

Body

Tailpiece

Seal

Seal Hole

Rod

Apply 3 layers of

sealant tape and a

small bead of pipe

sealant to threads.

Stopper

Nut

Faucet

Rod

Clip

Thumb

Screw

Link

1018258-2-F 6 Kohler Co.

5. Drain Installation-Style B

Remove the protective cover from the ﬂange.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Assemble the nut, ﬂat washer, and tapered gasket (tapered side

up) fully onto the body.

From the underside of the ﬁxture, insert the drain body up into

the drain hole.

From the top of the ﬁxture, securely hand tighten the ﬂange onto

the drain body.

Make sure the drain body seal hole is facing the back of the

ﬁxture, and securely tighten the nut.

Remove any excess putty or sealant.

Apply plumbers putty.

Flange

Tapered Gasket

Flat Washer

Nut

Drain Body

Fixture

Kohler Co. 7 1018258-2-F

6. Complete Drain Installation-Style B

Press the seal into the seal hole on the body.

Insert the stopper into the ﬂange.

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper rod. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper rod.

Hand tighten the rod nut.

Remove and adjust the stopper as needed so it lifts about 3/8″(1

cm) when opened. To adjust, rotate the threaded stopper rod in or

out as needed. Retighten the stopper nut.

Apply thread sealant tape to the tailpiece threads, then thread the

tailpiece to the body. Tighten the tailpiece securely.

Slide one end of the clip onto the rod. Slide the link onto the lift

rod with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the body and then into the hole

in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

1/2″(1.3 cm) above the lift rod hole.

Body

Clip

Stopper

Stopper Nut

Flange

Seal

Rod Nut

Tailpiece

Apply

thread

sealant.

Thumb

Screw

Stopper

Rod

Link

Rod

Lift

Rod

1018258-2-F 8 Kohler Co.

7. Supply Connections

If the lavatory is not installed, install it at this time according to

the lavatory manufacturer’s instructions.

Allow enough space for penetration of supply tubes into the

supply stops. Cut the supply tubes if necessary.

Connect the supply hoses to the supply stops. (Left is hot - right

is cold).

Tighten all connections.

8. Installation Checkout

Connect the P-trap.

Make sure all connections are tight.

Remove the aerator by turning it counterclockwise.

Remove the aerator by turning it counterclockwise. For

commercial faucets, use the supplied key to remove the aerator.

Open the drain.

Turn on the main water supply and check for leaks. Repair as

needed.

Open both hot and cold valves and run water through the spout

for about a minute to remove debris. Check for leaks.

Remove any debris from the aerator and reinstall.

Hot Cold

Aerator

Kohler Co. 9 1018258-2-F

Guide de l’Installation

Robinet Central de Lavabo

Outils et matériels

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de performance. Nos numéros de téléphone

et notre adresse du site internet sont au verso. Merci encore d’avoir

choisi la compagnie Kohler.

Avant de commencer

Respecter tous les codes de plomberie et de bâtiment locaux.

Couper l’alimentation d’eau principale.

Vériﬁer avec soin si les tubes d’évacuation ou d’alimentation

d’eau sont endommagés.

Pour de nouvelles installations, installer le robinet et le drain au

lavabo avant d’installer celui-ci.

Kohler Co. se réserve le droit d’apporter toutes modiﬁcations au

design des robinets et ceci sans préavis, comme spéciﬁé dans le

catalogue des prix.

Pinces

Tournevis

cruciforme #2

Clé hexagonale

de 3/16"

Joint

d'étanchéité

pour filetage

Joint

d'étanchéité

pour tuyau

Mastic de

plombier

Clé à molette

Kohler Co. Français-1 1018258-2-F

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Devonshire K-TS395-4S Bedienungsanleitung

Kohler

Kohler Archer K-2359X Montageanleitung

Kohler

Kohler Singulier 7787T-4 Bedienungsanleitung

Kohler

Kohler K-T12014 Montageanleitung

Kohler

Kohler TAHOE Bedienungsanleitung

Kohler

Kohler KUMIN 18655T-CP Bedienungsanleitung

Kohler

Kohler FLEXISPACE 2.0 K-23794T-1 Bedienungsanleitung

Kohler

Kohler K-11340X Montageanleitung

Kohler

Kohler K-7223 Bedienungsanleitung

Kohler

Kohler K-2953 Montageanleitung

Kohler

Kohler 77980T-4 Bedienungsanleitung

Kohler

Kohler K-6536 Bedienungsanleitung

Kohler

Kohler AVID 31137T-4 Bedienungsanleitung

Kohler

Kohler K-7127 Montageanleitung

Kohler

Kohler K-13491 Montageanleitung

Kohler

Kohler mira Bijou Bedienungsanleitung

Kohler

Kohler K-1418-G Kurzanleitung

Kohler

Kohler 23475-4-BL Bedienungsanleitung

Kohler

Kohler 11679T Bedienungsanleitung

Kohler

Kohler Kelston K-T13494 Montageanleitung

Kohler

Kohler K-7147T Bedienungsanleitung

Kohler

Kohler COMPOSED K-20257T-B-CP Bedienungsanleitung

Kohler

Kohler Rada 215 Series Bedienungsanleitung

Kohler

Kohler K-6814-3 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung