Kohler K-7223 Bedienungsanleitung

Installation Guide

Bath Drain

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-7223

1054248-2-B

Thank You For Choosing Kohler Company

Thank you for choosing Kohler Company. Your Kohler Company

product reﬂects the true passion for design, craftsmanship, artistry, and

innovation Kohler Company stands for. We are conﬁdent its

dependability and beauty will surpass your highest expectations,

satisfying you for years to come.

All the information in this guide is based upon the latest product

information available at the time of publication. At Kohler Company,

we strive to fulﬁll our mission of improving the level of gracious living

for each person who is touched by our products and services. We

reserve the right to make changes in product characteristics, packaging,

or availability at any time without notice.

Please take a few minutes to review this guide. If you encounter any

installation or performance problems, please call 1-800-4KOHLER

(1-800-456-4537) from within the USA and Canada, or 001-877-680-1310

from within Mexico.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Turn off the main water supplies.

Carefully inspect the ﬁttings for damage before installing.

For replacement installations, remove the wall covering from the

drain end of the bath and remove the existing drain.

Hacksaw or

Tubing Cutter

Plumbers Putty

Plus:

• Trap

• Emery Paper

• Lubricant

• Silicone Sealant (Optional)

Sealant Tape

1054248-2-B 2 Kohler Co.

Before You Begin (cont.)

The drain tee is reversible for above-the-ﬂoor or through-the-ﬂoor

installations.

If installing a new bath, install the drain before installing the

bath.

This drain is for use with the K-1166 overﬂowing bath.

The overﬂow ell and drain ell tubes may need to be cut for

proper ﬁt. Dry ﬁt or measure and cut them to the proper length.

If cutting is needed, remove any burrs from the tubes.

Kohler Co. reserves the right to make revisions in the design of

drains without notice, as speciﬁed in the Price Book.

Kohler Co. 3 1054248-2-B

1. Prepare the Site

NOTE: For freestanding bath installations: Use the cut-out template

provided with your bath to assist you. For drop-in bath

installations: Refer to the roughing-in dimensions illustrated.

Mark the drain location on the subﬂoor.

Using a hacksaw, cut the marked drain location in the subﬂoor.

Install the P-trap.

Install the ﬁnished ﬂoor material on the subﬂoor.

17-1/8" (43.5 cm)

19-7/8" (50.5 cm)

21-3/16"

(53.8 cm)

1054248-2-B 4 Kohler Co.

2. Install the Drain Ell

Apply a ring of plumbers putty or other sealant around the

underside of the strainer according to the putty manufacturer’s

instructions.

Set the gasket between the drain ell and the underside of the

bath.

Thread the strainer into the drain ell until snug. Do not fully

tighten at this time.

Strainer

Gasket

Bath

Stopper

Drain Ell

Apply plumbers putty.

Kohler Co. 5 1054248-2-B

3. Install the Overﬂow Ell

Using lubricant (not provided), lubricate the two O-rings on the

overﬂow ell.

Slide the O-rings into the grooves on the overﬂow ell.

Apply additional lubricant to the O-rings and the area

surrounding the O-rings.

Slide the overﬂow tube over the bottom end of the overﬂow ell.

Attach the washer to the overﬂow ell.

Apply a ring of plumbers putty or other sealant to the front side

of the washer according the putty manufacturer’s instructions.

Align the overﬂow ell with the overﬂow hole in the bath.

Thread the lock ring on the overﬂow ell until hand-tight.

Gasket

Overflow Ell

Lock Ring

Overflow

Tube

1054248-2-B 6 Kohler Co.

4. Assemble the Drain

NOTE: The same steps apply to both above-the-ﬂoor and

through-the-ﬂoor installations, but the tee is aligned differently.

Align as shown in the illustration.

Slide a coupling nut, then a gasket onto the overﬂow tube.

Slide a coupling nut, then a gasket onto the drain ell.

Align the overﬂow tube and drain ell with the tee. Align the tee

following the illustration for your style of installation.

Insert the tubes completely into the tee. If necessary cut the

overﬂow tube to the correct length. Remove any burrs.

Align the tubes and tighten the coupling nuts.

Apply thread sealant to the threads on the tailpiece.

Insert the tailpiece 1” (2.5 cm) to 2” (5.1 cm) inside the trap inlet.

The tailpiece may need to be cut for proper ﬁt.

Insert the tailpiece into the tee, then tighten with a pipe wrench.

Tee

Tailpiece

Overflow Tube

Gasket

Coupling Nuts

Through-the-Floor Installations

Drain Ell

Tee

Tailpiece

Gasket

Overflow Tube

Coupling Nuts

Drain Ell

Above-the-Floor Installations

Kohler Co. 7 1054248-2-B

5. Tighten the Drain Ell

WARNING: Risk of property damage. Do not reposition the

drain ell after the strainer body is tightened. Moving the

drain ell may damage the seal created when the strainer is

tightened, increasing the risk of leaking.

Insert pliers handles into the top of the strainer.

Turn the handles to securely tighten the strainer into the drain ell.

Remove any excess sealant.

1054248-2-B 8 Kohler Co.

6. Install the Overﬂow Hood

Ensure the length from the eye to end of the spring is 17-3/4″

(45.1 cm). To adjust the length: Loosen the nut on the rod, adjust

the rod, then retighten the nut.

NOTE: In order for the drain to function properly, assemble the lift

rod with the crank at the 8 o’clock position as illustrated.

Slide the lift rod eye and washer onto the crank, as illustrated.

Secure the lift rod eye and washer with the cotter pin.

Using a pliers, close the cotter pin.

NOTE: If the handle is not pre-assembled to the overﬂow hood,

secure the handle to the overﬂow hood with the provided screw at

this time.

Angle the lift rod assembly to the side, as illustrated, then insert

it into the overﬂow of the bath.

Using a Phillips screwdriver, secure the overﬂow hood to the

overﬂow ell with the screws provided.

NOTE: If the overﬂow hood will be exposed to high volumes of

direct water spray, apply silicone sealant around the overﬂow hood.

This will create a watertight seal.

Overflow Hood

Screws Cotter Pin

Lift Rod Eye

Lift Rod

Assembly

17-3/4"

(45.1 cm)

Handle

Rod

Nut

Brass

Washer

Kohler Co. 9 1054248-2-B

7. Complete the Installation

Install the drain linkage with the drain stopper and nut at least

half way down the threaded rod. The distance between the

underside of the stopper and the bath surface should be 1/2″(1.3

cm).

Adjustment

Remove the stopper from the threaded rod.

Remove the drain stopper, then loosen the nut on the threaded

rod. To raise the drain stopper, turn the nut counterclockwise. To

lower the drain stopper, turn the nut clockwise.

Reinstall the stopper onto the threaded rod.

Toggle the overﬂow hood handle to ensure the stopper moves up

and down at the distance of 1/2″(1.3 cm). Repeat the adjustment

procedure, if necessary.

Checkout

Make sure all connections are tight.

Close the overﬂow hood handle, then ﬁll the bath with water and

check for leaks.

Check for leaks. Repair as needed.

1/2"

(1.3 cm)

Drain Stopper

Nut

Threaded

Rod

Flange

1054248-2-B 10 Kohler Co.

Andere Handbücher für K-7223

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-10217 Bedienungsanleitung

Kohler

Kohler K-368 Bedienungsanleitung

Kohler

Kohler 77984T-4MU Bedienungsanleitung

Kohler

Kohler ALTERNA Bedienungsanleitung

Kohler

Kohler K-18865 Bedienungsanleitung

Kohler

Kohler 5024-T-0 Bedienungsanleitung

Kohler

Kohler K-7127 Bedienungsanleitung

Kohler

Kohler 72218T-B7-CP Montageanleitung

Kohler

Kohler K-6227 Montageanleitung

Kohler

Kohler Mira Showers Escape Thermostatic 9.8 kW Bedienungsanleitung

Kohler

Kohler K-6813 Montageanleitung

Kohler

Kohler K-2515 Montageanleitung

Kohler

Kohler K-72218 Montageanleitung

Kohler

Kohler Cachet Quiet-Close K-7671 Bedienungsanleitung

Kohler

Kohler K-3323X Montageanleitung

Kohler

Kohler MING K-20029T-RW1 Bedienungsanleitung

Kohler

Kohler STRAYT 37331-4 Bedienungsanleitung

Kohler

Kohler Fairfax K-12265 Montageanleitung

Kohler

Kohler URBANITY 23748T-9 Bedienungsanleitung

Kohler

Kohler K-1110-G Kurzanleitung

Kohler

Kohler K-2294 Bedienungsanleitung

Kohler

Kohler K-20199 Montageanleitung

Kohler

Kohler K-11618 Bedienungsanleitung

Kohler

Kohler Stargaze BubbleMassage K-1959-GHW Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung