Kohler K-14434 Bedienungsanleitung

Installation Guide

Single Control Bidet Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página“ Español-1”

K-14434

1032027-2-B

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Carefully inspect waste and supply tubing for any sign of

damage.

Replace waste or supply tubing if necessary.

For new installations, install the faucet before installing the bidet.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed within the Price Book.

Adjustable

Wrench Plumbers

Putty 1/8" Hex

Wrench

1032027-2-B 2 Kohler Co.

1. Faucet Body Installation

Apply a bead of plumbers putty to the underside of the faucet

body according to the putty manufacturer’s instructions.

Feed the faucet supply inlets through the bidet hole and position

the faucet and escutcheon. Slide the bracket and washer over the

stud and tighten the nut securely to the stud.

Bidet

Nut

Bracket

Washer

Stud

Supply Inlet

Escutcheon

Apply Plumbers

Putty.

Kohler Co. 3 1032027-2-B

2. Drain Style

Refer to the illustrations above to determine the drain style you

received with your faucet.

Please follow the instructions for your drain style.

Style A Drain Style B Drain

1032027-2-B 4 Kohler Co.

3. Drain Installation-Style A

Remove the protective material from the ﬂange.

Wrap the bottom 2/3 of the ﬂange threads with three layers of

sealant tape.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Insert the ﬂange into the ﬁxture drain hole.

Assemble the gasket (tapered side up) and washer to the ﬂange

and partially thread the nut to the ﬂange. Do not fully tighten the

nut at this time.

Install the body washer and drain body with the seal hole facing

the back of the ﬁxture and securely tighten the nut. Use care to

avoid scratching the ﬁnish.

Remove any excess putty or sealant.

Insert the stopper into the ﬂange.

Insert the seal into the seal hole on the body.

Seal

Stopper

Lavatory

Screw

Spring

Clip Gasket

NutNut

Link

Rod Seal

Flange

Apply Plumbers

Putty.

Apply 3 layers of

sealant tape to

bottom 2/3.

Washer

Body Washer

Drain Body

Kohler Co. 5 1032027-2-B

4. Complete Drain Installation-Style A

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper. Secure

with the body nut.

Remove and adjust the stopper so it lifts about 3/8″(1 cm) when

opened. To adjust, loosen the stopper nut and shorten or lengthen

the stopper as needed. Tighten the stopper nut.

Apply three layers of thread tape and a small bead of pipe

sealant to the tailpiece threads.

Thread the tailpiece to the body and tighten securely.

Slide one end of the clip onto the rod. Slide the link onto the rod

with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the faucet and then into the

hole in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

above the lift rod hole.

Faucet

Rod

Clip

Thumb

Screw

Link

1032027-2-B 6 Kohler Co.

5. Drain Installation-Style B

Remove the protective cover from the ﬂange.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Assemble the nut, ﬂat washer, and tapered gasket (tapered side

up) fully onto the body.

From the underside of the ﬁxture, insert the drain body up into

the drain hole.

From the top of the ﬁxture, securely hand tighten the ﬂange onto

the drain body.

Make sure the drain body seal hole is facing the back of the

ﬁxture, and securely tighten the nut.

Remove any excess putty or sealant.

Apply Plumbers

Putty.

Flange

Gasket

Washer

Nut

Drain Body

Fixture

Kohler Co. 7 1032027-2-B

6. Complete Drain Installation-Style B

Press the seal into the seal hole on the body.

Insert the stopper into the ﬂange.

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper. Hand

tighten the body nut.

Remove and adjust the stopper as needed so it lifts about 3/8″(1

cm) when opened. To adjust, rotate the threaded stopper rod in or

out as needed. Retighten the stopper nut.

Apply thread sealant tape to the tailpiece threads, and thread the

tailpiece to the body. Tighten the tailpiece securely.

Slide one end of the clip onto the rod. Slide the link onto the rod

with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the faucet and then into the

hole in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

1/2″(1.3 cm) above the lift rod hole.

Body

Rod

Clip

Stopper

Nut

Flange

Seal

Nut

Tailpiece

Apply

Thread

Sealant.

Thumb

Screw

Stopper Rod

Link

1032027-2-B 8 Kohler Co.

7. Single Control Link Installation

Identify the best hole in the link to allow full operation of the

drain rod and the lifting rod.

Align the link hole with the drain rod and slide the clip and the

link onto the drain rod with the thumbscrew facing the back of

the bidet.

To move the link to the proper position, squeeze the clip and

slide it along the rod.

If not already down, push the drain rod down to the open drain

position.

If required, loosen the thumbscrew on the link.

Align the link with faucet lifting rod and push the lift rod

through the holes in the link.

Ensure that the drain knob is at the bottom of the slot in the back

of the faucet.

With both the drain knob and the drain rod fully down, tighten

the thumbscrew on the lifting rod.

Test operation of the drain knob.

Clip

Link

Thumbscrew

Drain Knob

Faucet Body Lift Rod

Drain Rod

Kohler Co. 9 1032027-2-B

Single Control Link Installation (cont.)

As required, complete the installation of the bidet according to

the manufacturer’s instructions.

1032027-2-B 10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-7163 Bedienungsanleitung

Kohler

Kohler 11829T-B Bedienungsanleitung

Kohler

Kohler K-T376 Montageanleitung

Kohler

Kohler rada Thermotap-3 Bedienungsanleitung

Kohler

Kohler 73087T-B4 Bedienungsanleitung

Kohler

Kohler K-10086 Montageanleitung

Kohler

Kohler K-10481 Bedienungsanleitung

Kohler

Kohler K-1167 Bedienungsanleitung

Kohler

Kohler RUBICON 20147T-4 Bedienungsanleitung

Kohler

Kohler K-4350 Series Montageanleitung

Kohler

Kohler K-6536 Bedienungsanleitung

Kohler

Kohler SIMPLICE 596T-4 Bedienungsanleitung

Kohler

Kohler Reve K-5036BR Bedienungsanleitung

Kohler

Kohler K-10586 Montageanleitung

Kohler

Kohler K-2515 Montageanleitung

Kohler

Kohler K-1110-G Kurzanleitung

Kohler

Kohler PATIO Series Bedienungsanleitung

Kohler

Kohler K-6330 Bedienungsanleitung

Kohler

Kohler K-1002-H2 Bedienungsanleitung

Kohler

Kohler TROCADERO K-2247-1 Bedienungsanleitung

Kohler

Kohler STRAYT 37331A-4ND Bedienungsanleitung

Kohler

Kohler K-12177 Montageanleitung

Kohler

Kohler Memoirs Stately 3 Hole Basin Mixer Bedienungsanleitung

Kohler

Kohler K-12286-4 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung