Kohler PATIO Series Bedienungsanleitung

1070157-T01-E

Please read these instructions carefully to familiarize

yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is based upon the

latest product information available at the time of

publication. Kohler China reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning, and

warranty information -

please leave instructions for the

consumer

·-

Open end/adjustable wrenches

Tape measure

Basin wrench

Pipe wrench

Square

Level

Pliers

Socket wrench with sockets

Screw driver

Seal tape

Connection wire

Wire cutter

Insulation tape

Bushing

Drill

Sealant

RECOMMENDED TOOLS AND MATERIALSRECOMMENDED TOOLS AND MATERIALS

PATIO

INSTALLATION INSTRUCTIONS

VITREOUS CHINA TOUCHLESS URINAL

K-16320T-M/K-16321T-M(DC/ )

K-16320T-MC05/K-16321T-MC05(AC/ )

-1-

BEFORE YOU BEGINBEFORE YOU BEGIN

, 2009

528137

1070157-T01-E

Note: the sensing distance in the table is measured with a 30 30cm white board as the reflecting surface.

Model

Power

Liter per flushing

Temperature

Starting pressure

Testing time

Flushing mode

Sensing distance

16321T-M 16321T-MC05

220V AC 50/60Hz

Water pressure at 0.18~0.55 MPa:

No more than 1L

Environmental temperature: 1 to 55 C

0.05~0.86MPa

70cm away from sensing window (Automatic adjustiment range: 50~70cm)

About 2 seconds or 5 seconds (Automatic adjustment)

Flushing after used

2 "AAA" size alkaline batteries

16321T-MC05

0.18~0.55MPa. 1L

1~ 55 C

0.05~0.86MPa.

70cm ( 50~70cm)

25( )

220V 50/60Hz

16321T-M

2 7 (AAA 2)

30 30cm2

SENSOR SPECIFICATIONSSENSOR SPECIFICATIONS

-2-

Model

Power

Liter per flushing

Temperature

Starting pressure

Testing time

Flushing mode

Sensing distance

16320T-M 16320T-MC05

2 AAA size alkaline batteries""

220V AC 50/60Hz

Water pressure at 0.18~0.55 MPa:no more than 3.8L

Water pressure at 0.1 MPa:No more than 3L

Environmental temperature: 1 to 55 C

0.05~0.86MPa

70cm away from sensing window (Automatic adjustiment range: 50~70cm)

About 2 seconds or 5 seconds (Automatic adjustment)

Dual flushing

16320T-M 16320T-MC05

2 7 (AAA 2) 220V 50/60Hz

0.18~0.55MPa. 3.8L

0.1MPa. 3L

1~ 55 C

0.05~0.86MPa.

70cm ( 50~70cm)

25( )

1070157-T01-E

ROUGHING-IN

Notice: a. The dimensions above are just for reference.

b. The layout dimensions of water and outlet see

installation step B(Install the hook).

c. ** Indicates the location of inlet pipe, while inlet

connector size is G 1/2.

inlet

b. B( )

c. ** G 1/2

-3-

Unit:mm

Notice: To ensure an effective flush performance,

strongly recommended inner diameter of

water supply (including water meter, valve,

etc.) is no less than 25mm, and supplied

water pressure (sensor inlet dynamic

pressure) is 0.18MPa ~0.55MPa.

(

) 25mm (

) 0.18MPa ~0.55MPa

Reference Value

Kohler reserves the right to change marked dimensions without prior notice.

332

180

600 50 ext

145

55 642

303

455

G1/2

180

180 5

K-16320T-M/K-16320T-MC05/K-16321T-M/K-16321T-MC05

1070157-T01-E -4-

Outlet Downwards

1. Please install 16320T-MC05/16321T-MC05(AC) as below:

Please directly reference to Step 2 when installing 16320T-M/

16321T-M (DC).

CAUTION:

Please match 16306T-NA AC power unit when installing

16320T-MC05/16321T-MC05 (AC).

a. Outlet of AC power unit upward prohibited.

b. Do not connect 220V AC power supply to DC wiring

terminal.

c. Do not damage the covering of AC power unit or

remove screws to avoid leakage.

1. 16320T-MC05/ ( )

b. 220V DC

() 2

16320T-MC05/ ( ) 16306T-

16321T-MC05

16320T-M/16321T-M

16321T-MC05

CAUTION:

. When installing the power unit on the ceiling, please

chisel out a slot and layout bushing according to Fig., and

thread wire through the bushing.

One AC power unit can supply two

sensors at most.

Outlet Upwards

Connect to

Sensor

Connect to

Sensor

Connect to AC

Power Supply

Connect to AC

Power Supply

Notice:

. AC power unit connected to electric control box by

connection wire.

The length of the connection wire should keep

the connector out of the urinal. It s convenient

connect.

16306T-NA

AC Power Unit

Connector

Wire Prepared

By Customer

Connect With

Control Box

Ceiling

Slot

INSTALLATION

AC Power Unit

Bushing(In-wall)

()

Bushing

()

(In-wall)

Connect with the same color wire,

and protect connect area by insulation tape.

1070157-T01-E -5-

Notice:

f. Don't install the AC power unit in the free

space behind the urinal to avoid damaging

the AC power unit.

b. Do not connect the DC output of AC power

unit to AC power supply.

c. Do not connect to power supply while

installing. Connection line is not supplied.

AC connection wire with insulating sleeving

is recommended. Wire of which the

nominal section area of conductor is not

less than 0.5mm is also recommended.

DC connection line use wire of which the

nominal section area is not less than

0.3mm . It is cut according to acted

installation requirements(The length of cut

wire is recommended less than 10m).

d. The head AC power supply must be

protected with appropriate fuse.

e. Please confirm the AC power supply and

water supply should be shut off before

maintaining the products with AC power

related.

a. Keep the connector away from water. a.

0.5mm

0.3mm

( 10m)

2. Install urinal

Notes: a. Observe all local plumbing and building

codes.

b. Shut off the water supply.

c. Carefully inspect the new fixture for any sign

of damage.

d. Be very careful while hand ling vitreous

china products.

Note:

Install outlet connection

Ascertain the position for outlet connection according to

rough-in dimension.

Connect the outlet connection with the S-trap way. Insert the

gasket into the S-trap way as shown. Apply sealant on outlet

pipe, connect the outlet connection with outlet pipe.

Maybe different for different outlet connections.

X1 X1

1070157-T01-E

Install hook

Drill 2 mounting holes on the wall and install hook. Fix hook

on the wall by tightening screws.

-6-

Supply Pipe

Install the inlet hose of valve assy.

Take out the bracket of valve assy. Install the limited board (1).

Tighten the tighten screw (2).The inserting depth postion is

shown

Connect the inlet pipe with the water supply on the wall.

(1) (2)

(3)

as (3).

Limited Board

Tighten Screw

Bracket of Valve Assy.

(1)

Bracket of Valve

Tighten Screw

(2)

(3)

(600~700)

180

1070157-T01-E -7-

Install urinal

)

Lift up the urinal, level the installing hole on the back of the

urinal with the hook. Level the outlet connection which is

installed together with the strainer and the gasket on the S-

trap way. Then insert the outlet connection into the gasket.

(While the outlet connection is inserted, the S-trap way can

be crutched by hard exterded via the gap in the bottom of the

urinal to install it decently.) Then fix the urinal on the hook.

a. Avoid the urinal fallen on the floor to

damage the urinal or hurt somebody.

b. Avoid damaging the valve assy and wires.

c. Confirm the wires bare out of urinal base.

Notice:

d. Set the inlet hose and the inlet hose of

valve assy respectively on the both sides of

the S-trap way before installing urinal.

Inlet Hose of Valve Assy

Inlet Hose

Inlet Hose of Valve Assy

1070157-T01-E

3. Install the bracket assy.

Note:

Connect the outlet of valve assy, with the inlet hose.

The way of 16320T-M/ (DC) installation is as below:

Take out the battery box from the bracket assy. Loose the

screws of the battery box assy with a screw driver. Put 2

"AAA" size alkline batteries and tighten the battery box's

cover with the screws. Replace the battery box. Connect the

wires with the same color wires.

Don't mistake the polarity of the batteries and

don't mix the new and used batteries together.

Installing 16320T-MC05/ (AC) must connect the

AC power unit with control box assy with the same color wires.

16321T-M

16321T-MC05

()

16320T-M/16321T-M

16320T-MC05/16321T-MC05

Note:

Press the two sides spring hooks of bracket of valve assy

close to the center(1). Press the bracket up along the wall

and push it into arc gap of the urinal base(2) until the

spring hooks hangs on the urinal.

Please carefully handle the stainless steel plate

for its sharp edge will cause possible handcut.

(1)

(2)

When installing 16320T-MC05/16321T-MC05,

connect DC output

16320T-MC05/16321T-MC05

Inlet Hose

Connector

When installing 16320T-M/

16321T-M, connect battery box

16320T-M/16321T-M

Inlet Hose of Valve Assy.

Bracket of Valve

Outlet

Screw M2.5X20

M2.5X20

Cover of Battery Box

Battery Box

Bracket of Valve Assy

Spring Hook

(1)

Spring Hook

(2)

(1)

Urinal

-8-

1070157-T01-E

Push the bracket away from the wall(3), until the front hook

of the bracket hanging on the urinal.

(3)

Note:

Loose the tighten screw. Push the limited board to the

urinal withstanding the wall (4) and then tighten the tighten

screw (5).

a. When installing the 16320T-MC05/16321T-

MC05(AC), do not connect to power supply

until finish installation.

b. Taking out the bracket just need to athwort

the way of installations.

(5)

(4) (5)

a. 16320T-MC05/ ( )

220V

16321T-MC05

Limited Board

(3)

(4)

(5) Tighten Screw

Front Hook

-9-

1070157-T01-E

USER S GUIDE

Don t use this system until the power is on for 10

minutes.

The sensing distance will be adjusted and the system

will not work during this time.

Working Status

Before powering the system on, chear the unwanted objects

in front of the sensor window lest shortening the sensing

distance.

Sensing Distance

During the first 10 minutes, when powered on, the system is

in the phase of automatic regulation, and no operation is

required.

Set Working Status (Only for 16320T-M/16320T-

MC05)

The product comes our factory with:

1. The working status is set as dual-flush. If you want to

cancel the first flushing function, place manual flush stick

adjacent to right side of sensing window for more than 1

second during the 10-minute standby period (Human

presence in sensing range would cause the indicator to

flash fast).The sensor would generate a flushing cycle to

indicate the setup of the sensor has been adjusted to

afteruse flushing. If the action is not completed during this

10 minute, or you need to restore the working status to

dualflush, plug off the power cord and reconnect the power

supply until the indicator stops flashing and repeat the

above procedures.

2. The diction time is set as 2s to avoid improper function in

narrow toilets, the detection time is automatically set from

2s to 5s.

( 16320T-M/16320T-MC05)

10 (

)

2. 2

Deodorizing Flushing

The urinal will take a flush automatically when it’s used 3 or 4

times in 2 minutes.

2 3-4

Replacement of Batteries(Only for 16320T-

M/ )

When out of power, the indicator will flash every 2 seconds

and the sensor will not work until new batteries are supplied.

When replacing batteries, open the cover of battery box and

put in new batteries.

( 16320T-M/ )

16321T-M

Indicator

-10-

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Stance 14775-4-CP Montageanleitung

Kohler

Kohler 18359X-CL Bedienungsanleitung

Kohler

Kohler K-T14419 Montageanleitung

Kohler

Kohler K-20199 Montageanleitung

Kohler

Kohler K-4918 Bedienungsanleitung

Kohler

Kohler K-16135 Bedienungsanleitung

Kohler

Kohler MODERN LIFE K-21842T Bedienungsanleitung

Kohler

Kohler Trend K-11935 Montageanleitung

Kohler

Kohler Archer K-2359X Montageanleitung

Kohler

Kohler VINTAGE K-7158 Bedienungsanleitung

Kohler

Kohler K-7163 Bedienungsanleitung

Kohler

Kohler LUSTRA Bedienungsanleitung

Kohler

Kohler K-10349 Montageanleitung

Kohler

Kohler 77980T-4 Bedienungsanleitung

Kohler

Kohler K-45346T Bedienungsanleitung

Kohler

Kohler Centerset K-15241 Montageanleitung

Kohler

Kohler K-4177 Bedienungsanleitung

Kohler

Kohler K-302 Montageanleitung

Kohler

Kohler Sterling 225C7 Montageanleitung

Kohler

Kohler Wave 12791T-4 Bedienungsanleitung

Kohler

Kohler SAN RAPHAEL PRESSURE LITE K-3394 Bedienungsanleitung

Kohler

Kohler K-9053, K-9054 Montageanleitung

Kohler

Kohler Candide 7688K-4E3 Bedienungsanleitung

Kohler

Kohler K-3145 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung