Kohler K-19480 Bedienungsanleitung

Installation Guide

Single-Control Lavatory Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-19480

1050798-2-A

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Carefully inspect the waste and supply tubing for any sign of

damage.

This faucet is for use on a single-hole lavatory.

For new installations, install the faucet and drain to the lavatory

before installing the lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Thermometer

Strap

Wrench Thread

Sealant

Plumbers

Putty Hex

Wrench

Assorted

Screwdrivers

1050798-2-A 2 Kohler Co.

1. Install the Faucet

Thread the mounting studs into the holes in the bottom of the

faucet body.

NOTE: The base of the faucet may be attached to the lavatory using

either the supplied rubber washer or plumbers putty to form a

watertight seal. Do not attach the faucet to the lavatory using both

the rubber washer and plumbers putty.

For rubber washer attachment: Slide the washer over the supply

inlets and up to the faucet base.

For plumbers putty attachment: Apply the plumbers putty or

other sealant to the underside of the ﬂange of the faucet base

according to the putty manufacturer’s instructions.

Feed the faucet supply inlets through the faucet hole of the

lavatory, then position the faucet.

Slide the washer and bracket over the mounting studs, then

securely tighten the nuts to the mounting studs.

Nut Bracket

Washer

Lavatory

Mounting Stud

Supply Inlet

Apply

plumbers

putty.

Rubber

Washer

Kohler Co. 3 1050798-2-A

2. Install the Drain

Remove the protective cover from the ﬂange.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Assemble the nut, ﬂat washer, and tapered gasket (tapered side

up) fully onto the body.

From the underside of the ﬁxture, insert the drain body up into

the drain hole.

From the top of the ﬁxture, securely hand tighten the ﬂange onto

the drain body.

Make sure the drain body seal hole is facing the back of the

ﬁxture, and securely tighten the nut.

Remove any excess putty or sealant.

Apply plumbers putty.

Flange

Tapered Gasket

Flat Washer

Nut

Drain Body

Fixture

1050798-2-A 4 Kohler Co.

3. Complete the Drain Installation

Press the seal into the seal hole on the body.

Insert the stopper into the ﬂange.

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper rod. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper rod.

Hand tighten the rod nut.

Remove and adjust the stopper as needed so it lifts about 3/8″(1

cm) when opened. To adjust, rotate the threaded stopper rod in or

out as needed. Retighten the stopper nut.

Apply thread sealant tape to the tailpiece threads, then thread the

tailpiece to the body. Tighten the tailpiece securely.

Slide one end of the clip onto the rod. Slide the link onto the lift

rod with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the body and then into the hole

in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

1/2″(1.3 cm) above the lift rod hole.

Body

Clip

Stopper

Stopper Nut

Flange

Seal

Rod Nut

Tailpiece

Apply

thread

sealant.

Thumb

Screw

Stopper

Rod

Link

Rod

Lift

Rod

Kohler Co. 5 1050798-2-A

4. Connect the Supplies

If the lavatory is not installed, install it at this time. Follow the

lavatory manufacturer’s instructions.

NOTE: Connect the supply hose marked with a blue dot to the cold

supply.

Connect the supply hoses to the supply stops. (Left is hot - right

is cold.)

Supply

Stop

Supply

Hose

1050798-2-A 6 Kohler Co.

5. Installation Checkout

Connect the drain tailpiece into the P-trap.

Ensure that all connections are tight.

Using the tool provided, remove the aerator.

Turn on the main water supply and check for leaks. Repair as

needed.

Lift and rotate the faucet handle to the full hot position, then the

full cold position. Run water through the spout for about one

minute to remove any debris. Check for leaks and repair as

needed.

Push the lever handle down to close the water supplies, then

reinstall the aerator.

Aerator

Aerator Removal Tool

Kohler Co. 7 1050798-2-A

6. Optional Temperature Limiting Adjustment

NOTE: The water temperature does not need to be adjusted if the

maximum water temperature is below 105°F (41°C).

Lift and turn the lever handle to the full hot position.

Determine the temperature using a thermometer. If the

temperature exceeds 105°F (41°C), complete the following steps.

Using a small ﬂat-blade screwdriver, carefully pry the plug button

off the lever handle.

Loosen the setscrew on the handle with a hex wrench, then

remove the handle and bonnet.

Note the position of the locking ring relative to the inner geared

ring.

NOTE: To avoid damage to the locking ring during removal, pry

each side of the locking ring off the inner geared ring with an equal

and even technique.

Gradually pry each side of the locking ring up off of the inner

geared ring and onto the valve stem with a ﬂat-blade screwdriver.

Rotate the valve stem clockwise to increase temperature, or

counterclockwise to decrease temperature.

Reinstall the locking ring into the inner geared ring.

Reinstall the bonnet and handle to the faucet body.

Test the setting and make any adjustments as needed.

Plug Button

Handle

Bonnet

Inner

Geared

Ring Locking Ring

Setscrew

Locking Ring

Inner Geared

Ring

Valve Stem

1050798-2-A 8 Kohler Co.

Optional Temperature Limiting Adjustment (cont.)

After all adjustments have been made, use a hex wrench to

tighten the setscrew.

Press the plug button into place.

Kohler Co. 9 1050798-2-A

Guide d’installation

Robinet d’évier mono-contrôle

Outils et matériels

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de performance. Nos numéros de téléphone

et notre adresse du site internet sont au verso. Merci encore d’avoir

choisi la compagnie Kohler.

Avant de commencer

Respecter tous les codes de plomberie et de bâtiment locaux.

Couper l’alimentation d’eau principale.

Vériﬁer avec soin si les tubes d’évacuation ou d’alimentation

d’eau sont endommagés.

Ce robinet est conçu pour des lavabos à un oriﬁce.

Pour de nouvelles installations, installer le robinet et le drain au

lavabo avant d’installer celui-ci.

Kohler Co. se réserve le droit d’apporter toutes modiﬁcations au

design des robinets et ceci sans préavis, comme spéciﬁé dans le

catalogue des prix.

Thermomètre

Clé à

sangle Joint

d'étanchéité

pour filetage

Mastic de

plombier Clé

hexagonale

Tournevis

assortis

Kohler Co. Français-1 1050798-2-A

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler 11829T-B Bedienungsanleitung

Kohler

Kohler CUFF 37310M-4 Bedienungsanleitung

Kohler

Kohler K-997 Bedienungsanleitung

Kohler

Kohler K-1188BR Bedienungsanleitung

Kohler

Kohler K-11550 Bedienungsanleitung

Kohler

Kohler K-1110-G Kurzanleitung

Kohler

Kohler K-7465 Montageanleitung

Kohler

Kohler 22572T-9 Bedienungsanleitung

Kohler

Kohler K-2191 Bedienungsanleitung

Kohler

Kohler K-7702 Bedienungsanleitung

Kohler

Kohler K-251 Bedienungsanleitung

Kohler

Kohler 84625 Handbuch

Kohler

Kohler K-1018 Montageanleitung

Kohler

Kohler MAXISPACE K-77217T Bedienungsanleitung

Kohler

Kohler Botticelli K-2333 Montageanleitung

Kohler

Kohler K4915 Betriebsanleitung

Kohler

Kohler K-T195 Montageanleitung

Kohler

Kohler K-T9540 Montageanleitung

Kohler

Kohler 5024-T-0 Bedienungsanleitung

Kohler

Kohler K-702-N1 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Kohler

Kohler K-T15601 Bedienungsanleitung

Kohler

Kohler K-2331 Montageanleitung

Kohler

Kohler K23857-CP Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung