Kohler K-T15601 Bedienungsanleitung

Installation Guide

Single-Control Bath and Shower Trim

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-T15601 K-T15603

K-T15611 K-T15613

K-T15621

1006260-2-C

IMPORTANT INSTRUCTIONS

READ AND SAVE FOR THE

CONSUMER

WARNING: Risk of scalding or other severe injury.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

•Do not install a shut-off device on either outlet of this valve. The

installation of any such device may create a cross-ﬂow condition

at the valve and affect the water temperature.

•Factors that change the temperature of the water supplied to the

valve, such as seasonal water temperature changes, and water

heater replacement or servicing, will change the maximum water

temperature supplied by the valve and may create a scalding

hazard.

•The pressure-balanced valve will not compensate for changes in

the water supply temperature; adjust the maximum water

temperature setting of this pressure-balanced valve when such

changes occur.

•Pressure-balanced valves may not provide protection against

scalding if there is a failure of other temperature-limiting devices

elsewhere in the plumbing system.

The installer is responsible for installing the valve and adjusting the

maximum water temperature of this pressure-balanced valve

according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the installation or temperature

adjustment instructions in this document, in the United States please

contact our Customer Service Department at 1-800-4-KOHLER.

Outside the U.S., please contact your distributor.

IMPORTANT NOTICE TO INSTALLERS! Please ﬁll in the blanks in

the information box in the Homeowners Guide and on the valve label.

Retain the Homeowners Guide for future reference.

1006260-2-C 2 Kohler Co.

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

Observe all local plumbing and building codes.

The ﬁnished wall or bath/shower unit must be installed prior to

installing this trim.

We recommend that you determine if the maximum water

temperature is acceptable before installing this trim. If

temperature adjustment is needed, refer to the ″Water

Temperature Adjustment″section.

The valve shuts off by water pressure. Do not force the handle in

any direction. To turn the valve off, gently turn it to the ″Off″

position.

Shut off the main water supply.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

Thermometer

Strap

Wrench Thread

Sealant

Plumbers

Putty Hex

Wrench

Assorted

Screwdrivers

Kohler Co. 3 1006260-2-C

1. Install the Spout

CAUTION: Risk of internal seal damage. Do not use

petroleum-based lubricants when installing slip-ﬁt spouts. If the

spout will not slide over the tubing, use soapy water or a

silicone-based lubricant.

CAUTION: Risk of internal seal damage. Loosen the spout

setscrew with a 5/32″hex wrench prior to installing the spout.

Slip Fit Spouts

Remove the temporary nipple from the bath elbow.

Apply thread sealant and install a 1/2″copper tube so it extends

1-1/2″(3.8 cm) to 2-7/8″(7.3 cm) beyond the ﬁnished wall.

Deburr the copper tubing.

Loosen the setscrew with a 5/32″hex wrench.

Apply a bead of plumbers putty or other sealant around the inlet

end of the spout according to the manufacturer’s instructions.

Install the spout and carefully retighten the setscrew. Do not

overtighten the setscrew.

Remove all excess putty.

For Threaded Spouts

Remove the temporary nipple from the bath elbow.

Slip-Fit

Spouts

1-1/2" (3.8

cm) - 2-7/8"

(7.3 cm)

5/32" Hex Wrench

Setscrew

Copper

Tube

Apply

plumbers

putty.

Apply plumbers

putty.

Apply plumbers

putty.

Standard

Length

Spouts

Large Spouts

(17.8 cm)

3-7/8"

(9.8 cm)

Nipple

1006260-2-C 4 Kohler Co.

Install the Spout (cont.)

Apply thread sealant, and install a 1/2″nipple so it extends

3-7/8″(9.8 cm) beyond the ﬁnished wall for standard spouts and

7″(17.8 cm) for large spouts.

Apply a bead of plumbers putty or other sealant to the back of

the spout according to the manufacturer’s instructions.

Apply thread sealant to the nipple, and install the spout to the

nipple. Carefully tighten with a clean strap wrench.

Remove excess putty.

Kohler Co. 5 1006260-2-C

2. Install Showerhead

CAUTION: Risk of product damage. To avoid plugging the

showerhead spray outlets, use thread sealant tape on the shower

arm threads. Do not use thread sealant compound (pipe dope).

Remove the temporary nipple from the shower elbow.

Apply a bead of plumbers putty or other sealant to the back of

the escutcheon according to the manufacturer’s instructions.

Slide the escutcheon over the shower arm.

Apply thread sealant tape and install the shower arm to the

shower elbow.

Carefully tighten with a clean strap wrench.

Press the escutcheon against the ﬁnished wall.

Remove all excess putty.

With the showerhead off, ﬂush out the system.

Apply thread sealant tape to the shower arm. Install the screen

washer (if required for your model) and thread the showerhead

to the shower arm.

Escutcheon

Shower

Elbow

Apply

plumbers

putty.

Shower Arm

Showerhead

Shower Elbow

Escutcheon

Screen Washer

Showerhead

Shower Arm

1006260-2-C 6 Kohler Co.

3. Water Temperature Adjustment

CAUTION: Risk of personal injury. The water temperature

should never be set above 120° F (49° C).

NOTE: Do not remove the O-ring and collar at this time. Removing

the O-ring and collar will change the factory setting for the

maximum water temperature.

Turn the valve clockwise to the full open position and let the hot

water run for several minutes. Position a thermometer in the

water stream and check the temperature.

For minor water temperature changes, adjust the setscrew, and

recheck the water temperature.

For major water temperature changes, remove the O-ring and

collar from the valve stem. Slowly rotate the valve stem until the

desired maximum water temperature is reached.

Reinstall the collar on the valve stem with the setscrew against

the side of the tab.

Reinstall the O-ring, rotate the valve stem counterclockwise to

shut the water off.

Recheck the water temperature to ensure desired maximum water

temperature.

NOTE: After adjustment, complete the required information on the

valve label (if supplied).

O-Ring

Setscrew

Tab

Collar

Setscrew

Valve

Label

Standard

Valve

High Flow

Valve

Stem

Kohler Co. 7 1006260-2-C

4. Install the Faceplate and Handle

CAUTION: Risk of product damage to the K-306–KS valve

assembly. When using this valve in a ﬁberglass or acrylic

installation, use the Thin Wall Installation Kit (88526).

Remove and discard the plaster guard and/or dome, if installed.

Install the faceplate onto the valve. Secure with two screws. Do

not overtighten.

Rotate the valve stem fully counterclockwise.

Slide the sleeve over the valve stem.

Lever Handle

Properly align the handle downward.

Press the handle and insert ﬁrmly onto the valve stem.

Secure the handle in place with the washer and screw.

Press the plug button ﬁrmly into place in the handle.

Acrylic Handle

Attach the insert and align it so the dot on the front edge is

facing downward in the 6 o’clock position.

Slide the O-ring into position and attach the handle. Make sure

the handle is aligned identically to the insert.

Secure the handle in place with the washer and screw.

Push the plug button ﬁrmly into place in the handle.

Screw

O-Ring

Insert

Washer

Handle

Handle Plug Button

Valve Stem

Faceplate

Screw

Sleeve

Discard plaster guard

with dome.

1006260-2-C 8 Kohler Co.

Guide d’installation

Baignoire mono-contrôle et garniture de

douche

INSTRUCTIONS IMPORTANTES

À LIRE ET À LAISSER AU CLIENT

AVERTISSEMENT : Risque de brûlures ou de blessures graves.

•Avant de commencer l’installation, l’installateur doit régler la

température maximale de l’eau de cette valve pour réduire au

minimum les risques de brûlures, ceci conformément à la norme

ASTM F 444.

•Ne pas installer un dispositif d’arrêt sur les sorties de cette valve.

L’installation d’un tel dispositif peut créer une condition

d’écoulement croisé au régulateur et modiﬁer la température de

l’eau.

•Les facteurs qui changent la température de l’eau alimentée à

cette valve, tels que les changements de température d’eau

saisonniers, et le remplacement ou l’entretien du chauffeau,

changeront la température maximale de l’eau fournie par le

régulateur et pourront présenter un danger de brûlures.

•La valve à pression équilibrée ne compensera pas les

changements de température d’alimentation d’eau; ajuster la

température maximale de cette valve à pression équilibrée si de

tels changements se produisent.

•Les valves à pression équilibrée peuvent ne pas assurer une

protection contre les brûlures en cas de défaillance d’autres

dispositifs de limitation de température installés ailleurs sur le

réseau de plomberie.

L’installateur est responsable de l’installation de la valve et du

réglage de la température maximale de l’eau de cette valve à pression

équilibrée conformément aux instructions.

Cette valve satisfait ou excède les exigences des normes ANSI

A112.18.1M et ASSE 1016.

S’il ne vous est pas possible de comprendre les instructions

d’installation ou de réglage de la température données par ce

document, veuillez contacter notre département du service clientèle

aux États-Unis.1-800-4-KOHLER. Hors des États-Unis, veuillez

contacter votre distributeur.

Kohler Co. Français-1 1006260-2-C

INSTRUCTIONS IMPORTANTES (cont.)

AVIS IMPORTANT AUX INSTALLATEURS! Veuillez remplir le

coupon dans le guide du propriétaire ainsi que sur l’étiquette de la

valve. Conserver le guide du propriétaire pour future référence.

Outils et matériels

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de fonctionnement. Nos numéros de

téléphone et notre adresse du site internet sont au verso. Merci encore

d’avoir choisi la compagnie Kohler.

Avant de commencer

Respecter tous les codes de plomberie et de bâtiment locaux.

Le mur ﬁni ou la baignoire/douche doit être installé avant

d’installer cette garniture.

Nous conseillons de déterminer si la température maximale de

l’eau est acceptable avant d’installer la garniture. Si un réglage de

température est nécessaire, se référer à la section ″Réglage de la

température d’eau″.

La valve s’arrête par pression d’eau. Ne pas forcer la poignée

dans aucune direction. Pour fermer la poignée, la tourner

doucement sur la position ″Off″.

Couper l’alimentation d’eau principale.

Thermomètre

Clé à

sangle Joint

d'étanchéité

pour filetage

Mastic de

plombier Clé

hexagonale

Tournevis

assortis

1006260-2-C Français-2 Kohler Co.

Andere Handbücher für K-T15601

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-1124-G Kurzanleitung

Kohler

Kohler K-5414 Betriebsanleitung

Kohler

Kohler WaterTile K-8030 Bedienungsanleitung

Kohler

Kohler K-T395 Montageanleitung

Kohler

Kohler K-705771 Montageanleitung

Kohler

Kohler TOOBI K-15477T Bedienungsanleitung

Kohler

Kohler K-6284 Montageanleitung

Kohler

Kohler Mira Event XS Bedienungsanleitung

Kohler

Kohler KARAT K-2960X Montageanleitung

Kohler

Kohler K-2443 Bedienungsanleitung

Kohler

Kohler K-3393 Montageanleitung

Kohler

Kohler PURIST 10129T-4 Bedienungsanleitung

Kohler

Kohler K-3900 Bedienungsanleitung

Kohler

Kohler SIMPLICE 596T-4E Bedienungsanleitung

Kohler

Kohler Serif 5 BubbleMassage K-1337-G Bedienungsanleitung

Kohler

Kohler ODEON K-8766 Bedienungsanleitung

Kohler

Kohler K-11076 Montageanleitung

Kohler

Kohler FAMILY CARE Bedienungsanleitung

Kohler

Kohler 22327T-7 Bedienungsanleitung

Kohler

Kohler K-T9493 Bedienungsanleitung

Kohler

Kohler Karbon K-6227A Bedienungsanleitung

Kohler

Kohler K-1002-H2 Montageanleitung

Kohler

Kohler Kumin K-104K36-SANA-CP Bedienungsanleitung

Kohler

Kohler STRAYT 37331T Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung