Kohler K-20099T-Y Bedienungsanleitung

1298232-T01-C

PAPER

INSTALLATION INSTRUCTIONS

TOUCHLESS URINAL

K-20099T-Y(0.5L DC/0.5 )

K-20099T-YC05(0.5L AC/0.5 )

K-20099T-W(1L DC/1 )

K-20099T-WC05(1L AC/1 )

K-20099T(2.5L DC/2.5 )

K-20099T-C05(2.5L AC/2.5 )

-1-

Please read these instructions carefully to familiarize

yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is based upon the

latest product information available at the time of

publication. Kohler China reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning, and

warranty information -

please leave instructions for the

consumer

Fixture dimensions are nominal and conform to tolerances

established by ASME Standards (A112.19.2-2018).

The product complies with GB 6952-2015, GB 28377-

2019.

ASME (A112.19.2-

2018)

GB 6952-2015 GB 28377-2019

Open end/adjustable wrenches

Tape measure

Basin wrench

Pipe wrench

Square

Level

Pliers

Socket wrench with sockets

Screw driver

Seal tape

Connection wire

Wire cutter

Insulation tape

Bushing

Drill

Sealant

RECOMMENDED TOOLS AND MATERIALS(NOT SUPPLIED)RECOMMENDED TOOLS AND MATERIALS(NOT SUPPLIED)

()

BEFORE YOU BEGIN

2020

No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 528137

2 528137

8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA 256410

8 256410

NO.1 KOHLER STREET, ECONOMIC DEVELOPMENT ZONE OF FAKU COUNTY, SHENYANG LIAONING PROVINCE, PRC 110400

1 110400

POST CODE:

1298232-T01-C -2-

0.18~0.55MPa. 0.5L

0.18~0.55MPa. 1L

1~ 55 C

0.05~0.86MPa.

70cm ( 50~70cm)

25( )

2 7 (AAA 2)

SPECIFICATIONS

Power

Model

Liter per flushing

Temperature

Starting pressure

Sensing distance

Testing time

Flushing mode

Note: the sensing distance in the table is measured with a 30 X 30cm white board as the reflecting surface.

Water pressure at 0.18~0.55 MPa: Average flushing no more than 0.5L

Water pressure at 0.18~0.55 MPa: Average flushing no more than 1L

Water pressure at 0.18~0.55 MPa: Average flushing no more than 2.5L

Environmental temperature: 1 to 55 C

0.05~0.86MPa

70cm away from sensing window (Automatic adjustiment range: 50~70cm)

About 2 seconds or 5 seconds (Automatic adjustiment)

Flushing after used

K-20099T-Y

K-20099T-W

K-20099T

K-20099T-Y

K-20099T-W

K-20099T-YC05

K-20099T-WC05

K-20099T-C05

K-20099T-YC05

K-20099T-WC05

2 AAA size alkaline batteries""

220V AC 50/60Hz

1298232-T01-C

ROUGHING-IN

Unit:mm

Reference Value

Kohler reserves the right to change marked dimensions without prior notice.

Notice: a. The dimensions above are just for reference.

b. The layout dimensions of water and outlet see

installation step A(Install the hook).

c. ** Indicates the location of inlet pipe, while inlet

connector size is G 1/2.

d. * Recommended dimensions for installation only,

please adjust according to actual situation.

inlet

b. A( )

c. ** G 1/2

d. *

450

183 117

680

148**

252

116

160

85**

250

600*

410

316

Supply

50ext

30 X 30cm2

0.18~0.55MPa. 2.5L

1~ 55 C

0.05~0.86MPa.

70cm ( 50~70cm)

25( )

2 7 (AAA 2)

K-20099T K-20099T-C05

220V AC 50/60Hz

Notice: To ensure an effective flush performance,

strongly recommended inner diameter of

water supply (including water meter, valve,

etc.) is no less than 25mm, and supplied

water pressure (sensor inlet dynamic

pressure) is 0.18MPa ~0.55MPa.

(

) 25mm (

) 0.18MPa ~0.55MPa

-3-

1298232-T01-C -4-

A. Install hangers

Locate the position for the hook and install the hook.

INSTALLATION

450

183 117

148**

85** Supply 464*

B. Install waste pipe connector

Pre-install the waste pipe connector. In step C, waste pipe

connector shall be adjusted to match with the plastic pipe of

the urinal. Make sure the connector is completely sealed with

the pre-buried waste pipe.(Gasket of waste pipe connector

shall be soaked into water for 2 seconds to lubricate.)

(

)

Wall

Pre-installed waste

pipe connector

Insert the connector into the waste

pipe in the wall along this direction.

Move the gasket to front

of the pipe before

connecting to the urinal.

C. Install urinal

1. Hang the urinal onto the hangers.

4. Apply silicone sealant between urinal and wall.

Align the waste pipe connector with the plastic pipe of the

urinal. Tighten the nut of the connector. Seal the connector

and the pre-buried waste pipe if necessary.

Connect valve inlet and corner valve.

1. ( D )

1298232-T01-C -5-

D. Adjust the hanger

1. As shown in the picture below, firmly press the hanger with

the bolt through the waist-shaped hole.

Fixing Hole

Waist-shaped Hole

2. As shown in the picture below, if the position of the urinal

needs to be adjusted, please take down the urinal and

knock the hanger slightly to adjust its position upwards and

downwards.

3. After the position of the urinal is decided, completely fix the

hanger with the bolt through the fixing holes on the hanger.

Adjust Upwards and Downwards

E. Install the drain and the plastic trap

NOTE:

E. ( )

1. Put the washer onto the drain and insert it into the hole.

2. Put the gasket and nut on the bottom.

Do not over screw the nut in this step, because it is

to be screwed tight in the next step after the pipe is

installed.

(pre-installed in

factory)

3. Connect the hose with the trap.

4. As shown in the picture, screw the crossbar into the screw

head of filter cap (2-3 turns, as long as it doesn't fall), place

the crossbar into the opening of the connector and swivel

the filter cap to make the crossbar stuck inside the

connector, continue to screw tight.

5. Screw tight the nut of the drain mentioned in step.

4. 2-3

5. 2

1298232-T01-C

Outlet Downwards

G. Power connection

1. Please install K-20099T-YC05/K-20099T-WC05/K-20099T-

C05(AC) as below:

1) Please match AC power unit when installing K-20099T-

YC05/K-20099T-WC05/K-20099T-C05(AC).

a. Outlet of AC power unit upward prohibited.

b. Do not connect 220V AC power supply to DC wiring

terminal.

c. Do not damage the covering of AC power unit or

remove screws to avoid leakage.

CAUTION:

Outlet Upwards

Connect to

Sensor

Connect to

Sensor

Connect to AC

Power Supply

Connect to AC

Power Supply

1. K-20099T-YC05/K-20099T-WC05/K-20099T-C05(

)

b. 220V DC

1) K-20099T-YC05/K-20099T-WC05/K-20099T-C05(

)

3) When installing the power unit on the ceiling, please chisel

out a slot and layout bushing according to Fig., and thread

wire through the bushing.

One AC power unit can supply two

sensors at most.

CAUTION:

2) AC power unit connected to electric control box by

connection wire.

The length of the connection wire should keep

the connector out of the urinal. It s convenient

connect.

Notice:

Ceiling

Slot

AC Power Unit

Bushing(In-wall)

()

Bushing

()

(In-wall)

AC Power Unit

Connector

Wire Prepared

By Customer

Connect With

Control Box

Connect with the same color wire,

and protect connect area by insulation tape.

-6-

F. Install the Valve

Install the valve into the urinal. Fasten with screw and gasket.

1298232-T01-C

2. The way of installation

is as below.

Take out the battery box from the bracket assy. Loose the

screws of the battery box assy with a screw driver. Put 2

"AAA" size alkline batteries and tighten the battery box's

cover with the screws. Replace the battery box. Connect the

wires with the same color wires.

Don't mistake the polarity of the batteries and

don't mix the new and used batteries together.

Note:

K-20099T-Y/K-20099T-W/K-20099T 2. K-20099T-Y/K-20099T-W/K-20099T( )

Notice:

f. Don't install the AC power unit in the free

space behind the urinal to avoid damaging

the AC power unit.

b. Do not connect the DC output of AC power

unit to AC power supply.

c. Do not connect to power supply while

installing. Connection line is not supplied.

AC connection wire with insulating sleeving

is recommended. Wire of which the

nominal section area of conductor is not

less than 0.5mm is also recommended.

DC connection line use wire of which the

nominal section area is not less than

0.3mm . It is cut according to acted

installation requirements(The length of cut

wire is recommended less than 10m).

d. The head AC power supply must be

protected with appropriate fuse.

e. Please confirm the AC power supply and

water supply should be shut off before

maintaining the products with AC power

related.

a. Keep the connector away from water. a.

0.5mm

0.3mm

( 10m)

(

)

NOTE:

For Retrofit Installations

For New Installations

If a pre-existing waste pipe will be used and will result

in an acceptable rim height (refer to the rough-in dimensions),

follow the retrofit installation instructions.

Turn the water supply line off, remove the existing urinal,

then cap off the water supply line inside the wall.

Install waste pipe as necessary to conform to the

roughing-in dimensions.

Install adequate support framing for the hangers as

needed.

Connector

Inlet Hose of Valve Assy.

Bracket of Valve

Outlet

Screw M2.5X20

M2.5X20

Cover of Battery Box

Battery Box

-7-

1298232-T01-C

USER S GUIDE

Don t use this system until the power is on for 10

minutes.

The sensing distance will be adjusted and the system

will not work during this time.

Working Status

Before powering the system on, chear the unwanted objects

in front of the sensor window lest shortening the sensing

distance.

Set Working Status (Only for K-20099T/K-20099T-

C05)

The product comes our factory with:

1. The working status is set as dual-flush. If you want to

cancel the first flushing function, place manual flush stick

adjacent to right side of sensing window for more than 1

second during the 10-minute standby period (Human

presence in sensing range would cause the indicator to

flash fast). The sensor would generate a flushing cycle to

indicate the setup of the sensor has been adjusted to after

use flushing. If the action is not completed during this 10

minute, or you need to restore the working status to

dualflush, plug off the power cord and reconnect the power

supply until the indicator stops flashing and repeat the

above procedures.

2. The diction time is set as 2s to avoid improper function in

narrow toilets, the detection time is automatically set from

2s to 5s.

( K-20099T/K-20099T-C05)

10 (

)

2. 2

-8-

Sensing Distance

During the first 10 minutes, when powered on, the system is

in the phase of automatic regulation, and no operation is

required.

Deodorizing Flushing

The urinal will take a flush automatically when it’s used 3 or 4

times in 2 minutes.

2 3-4

Replacement of Batteries(Only for DC)

When out of power, the indicator will flash every 2 seconds

and the sensor will not work until new batteries are supplied.

When replacing batteries, open the cover of battery box and

put in new batteries.

()

Indicator

1298232-T01-C -9-

Manual Flushing

Approach the supplied special magnetic stick (flushing control

stick) to the sensor lens. The system is now at a manual

status and the indicator will flash every 1 seconds. Approach

the flushing control stick to the sensor lens once, it'll flush

once. This status will last for about 8 minutes until turns to the

normal working status.

If the flushing control stick keeps near to the

sensing window for 30 seconds, the manual

status will be terminated automatically and

reassume the normal working status.

()

Notice:

Used in places of low water pressure

If the flushing amount is limited due to low water pressure,

you can set a long time washing with flushing control stick.

Operate as follows: Ten minutes after power-on, you can

switch between two wash times by putting the flushing control

stick near the right side of sensing window. There will be a 2-

second rinse after you complete the setting. If you need to

reset the wash time, you must cut off the power and restart

the sensor and 10 minutes later, you're able to switch wash

time with flushing control stick.

Under the normal water pressure, it is not

recommended to use this flushing method in

order to prevent excessive flushing and water

spills out.

Note:

()

Flushing Control Stick

1298232-T01-C

Urinal Repair

When repairing, you don t have to dismount the sensor.

Cover the sensing window with tape and work with ease.

: Don t use very adhesive tape in case the scar

will be hard to remove.

Notice

Clean the Filter Screen

If the flushing volume reclines sharply after installation or

used for a long time with no cause from water pressure, the

filter may need a wash. Please operate as following steps:

Remove the bracket of valve assy. Loose the inlet hose firstly.

Loose the inlet hose of valve assy. and then take out the filter.

Clean it with a brush and reinstall.

a. Turn off the water supply before cleaning

the filter, also power off when used the AC

power supply.

b. Avoid damaging or losing the filter during

cleaning.

Caution:

MAINTENANCE

Filter

Bracket of Valve

Connector

Inlet Hose of Valve Assy.

-10-

Care & Clean

Keep the sensing window clean. Wipe with soft cloth and mild

cleaner.

a. Do not use dust-removing powder, abrasive powder

or cleaner containing oil, acid or alkaline ingredient.

b. Do not spray air-refresher, disinfector, or other

deodorizing, cleaning solvent directly into the

sensing window.

c. Keep wire away from water.

d. Don t attack the sensor window.

Notice:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-9053, K-9054 Montageanleitung

Kohler

Kohler K-6227 Montageanleitung

Kohler

Kohler K-T609 Bedienungsanleitung

Kohler

Kohler Rada 215 Series Bedienungsanleitung

Kohler

Kohler K-3145 Montageanleitung

Kohler

Kohler K-2419 Montageanleitung

Kohler

Kohler K-10217 Montageanleitung

Kohler

Kohler K-T944 Bedienungsanleitung

Kohler

Kohler MOXIE 99107T Bedienungsanleitung

Kohler

Kohler PureWarmth K-10349-96 Montageanleitung

Kohler

Kohler Bellhaven K-T11552 Bedienungsanleitung

Kohler

Kohler FLIGHT NEUS E62C70-00 Bedienungsanleitung

Kohler

Kohler K-5026 Montageanleitung

Kohler

Kohler K-7167 Montageanleitung

Kohler

Kohler Archer K-2359 Bedienungsanleitung

Kohler

Kohler K-T16225 Montageanleitung

Kohler

Kohler K-9404 Bedienungsanleitung

Kohler

Kohler BRIVE+ K-8703IN-1WH Bedienungsanleitung

Kohler

Kohler Rada T1 Bedienungsanleitung

Kohler

Kohler K-9132 Bedienungsanleitung

Kohler

Kohler C3-455 Quiet-Close K-8298-CR Bedienungsanleitung

Kohler

Kohler 73078T-4 Bedienungsanleitung

Kohler

Kohler K-17248 Bedienungsanleitung

Kohler

Kohler K-R399 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung