Kohler Bellhaven K-T11552 Bedienungsanleitung

Installation Guide

Single-Control Bath and Shower Trim

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-T11552 K-T11553

1064111-2-A

IMPORTANT INSTRUCTIONS

WARNING: Risk of scalding or other severe injury.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

•Do not install a shut-off device on either outlet of this valve. The

installation of any such device may create a cross-ﬂow condition

at the valve and affect the water temperature.

•Factors that change the temperature of the water supplied to the

valve, such as seasonal water temperature changes, and water

heater replacement or servicing, will change the maximum water

temperature supplied by the valve and may create a scalding

hazard. The pressure-balanced valve will not compensate for

changes in the water supply temperature; adjust the maximum

water temperature setting of this pressure-balanced valve when

such changes occur.

•Pressure-balanced valves may not provide protection against

scalding if there is a failure of other temperature-limiting devices

elsewhere in the plumbing system.

WARNING: Risk of product damage. Only silicone based

lubricants should be used with these valves. Use of petroleum

based lubricants on the valve is harmful to the O-rings, seals,

and plastic components. Use of petroleum based lubricants will

void the warranty.

The installer is responsible for installing the valve and adjusting the

maximum water temperature of this pressure-balanced valve

according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the installation or temperature

adjustment instructions in this document, in the United States please

contact our Customer Service Department at 1-800-4-KOHLER.

Outside the U.S., please contact your distributor.

IMPORTANT NOTICE TO INSTALLERS! Please ﬁll in the blanks in

the information box in the Homeowners Guide and on the valve label.

Retain the Homeowners Guide for future reference.

1064111-2-A 2 Kohler Co.

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

CAUTION: Risk of personal injury. The water temperature

should never be set above 120° F (49° C).

Observe all local plumbing and building codes.

The ﬁnished wall or bath/shower unit must be installed prior to

installing this trim.

Before installing the trim, determine if the maximum water

temperature is acceptable to the user. If temperature adjustment is

needed, refer to the ″Optional Temperature Limiting Adjustment″

section of this guide.

The valve shuts off by water pressure. Do not force the handle in

any direction. To turn the valve off, gently turn it to the ″OFF″

position.

Shut off the main water supply.

Refer to the caulk or silicone sealant manufacturer’s instructions

for preferred caulking techniques.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

Assorted

Screwdrivers

Strap

Wrench

Plumbers

Putty

Hex Wrench

Thread Sealant

Tape

Caulk or

Silicone Sealant

Thermometer

Kohler Co. 3 1064111-2-A

1. Optional Temperature Limiting Adjustment

CAUTION: Risk of personal injury. The water temperature

should never be set above 120°F (49°C).

NOTE: Do not remove the O-ring and collar at this time. Removing

the O-ring and collar will change the factory setting for the

maximum water temperature.

Turn the valve clockwise to the full open position and let the hot

water run for several minutes. Position a thermometer in the

water stream and check the temperature.

If the water temperature does not require changes, proceed to

the ″Install the Spout″section of this guide.

For minor water temperature changes, adjust the setscrew, and

recheck the water temperature.

For major water temperature changes, remove the O-ring and

collar from the valve stem. Slowly rotate the valve stem until the

desired maximum water temperature is reached.

Reinstall the collar on the valve stem with the setscrew against

the side of the tab.

Reinstall the O-ring, rotate the valve stem counterclockwise to

shut the water off.

Recheck the water temperature.

Complete the information on the valve label (if supplied).

Setscrew

O-Ring O-Ring

Tab

Valve

Stem Valve

Label

Collar

1064111-2-A 4 Kohler Co.

2. Install the Spout

Slip-Fit Spout

Remove the temporary nipple from the bath elbow.

Apply thread sealant tape to the bath elbow, then install a 1/2″

copper tube to extend from 2″(5.1 cm) to 2-5/8″(6.7 cm) beyond

the ﬁnished wall.

Smooth the edges of the copper tubing.

Loosen the setscrew from underneath the spout with a 5/32″hex

wrench.

Apply a bead of plumbers putty or other sealant around the

spout base. Leave a small gap free of putty or other sealant at the

bottom of the spout base.

Slide the spout onto the copper tubing, push the spout base

against the ﬁnished wall, then carefully retighten the setscrew.

Remove excess putty.

Threaded Spout

Remove the temporary nipple from the bath elbow.

Apply thread sealant tape to the bath elbow, then install a 1/2″

nipple to the bath elbow to extend 4-1/4″(10.8 cm) beyond the

ﬁnished wall.

Apply thread sealant tape to the pipe nipple.

Apply a bead of plumbers putty or other sealant to the spout

base.

Setscrew

Copper Tube

Slip-Fit Spout

Nipple

Threaded Spout

Apply plumbers

putty.

Apply plumbers

putty.

4-1/4"

(10.8 cm)

2" (5.1 cm) -

2-5/8" (6.7 cm)

5/32" Hex

Wrench

Kohler Co. 5 1064111-2-A

Install the Spout (cont.)

Apply thread sealant to the nipple and install the spout to the

nipple.

Using a clean strap wrench, carefully tighten the spout to the

nipple.

Remove excess putty.

1064111-2-A 6 Kohler Co.

3. Install the Showerhead

CAUTION: Risk of product damage. To avoid clogging the

showerhead spray outlets, use thread sealant tape on the shower

arm threads. Do not use thread sealant compound (pipe dope).

Remove the temporary nipple from the shower elbow.

Apply thread sealant tape to the long end of the shower arm.

Using a clean strap wrench, secure the long end of the shower

arm to the shower elbow.

Apply a bead of plumbers putty or other sealant to the back of

the escutcheon according to the putty manufacturer’s instructions.

Slide the escutcheon onto the shower arm and press the

escutcheon against the ﬁnished wall.

Remove all excess putty.

Turn the main water supply on.

Run hot and cold water through the shower arm to ﬂush out dirt

and debris.

Apply thread sealant tape to the short end of the shower arm.

Thread the showerhead onto the shower arm.

Apply

plumbers

putty.

Shower Arm

Shower Elbow

Escutcheon

Showerhead

Kohler Co. 7 1064111-2-A

4. Install the Faceplate and Handle

Remove and discard the plaster guard and/or dome, if installed.

Position the retainer onto the valve stem. Secure the retainer to

the valve stem with the two #10-24 x 3/4″screws.

Place the escutcheon over the threads of the retainer. The notch

on the escutcheon should be in the 6 o’clock position.

Rotate the valve stem fully counterclockwise to the ″OFF″

position.

IMPORTANT! There is a short end and a deep end on the stem

adapter. Select the proper end to be placed on the valve stem based

on the ﬁnished wall depth.

Finished Wall Depth Stem Adapter Direction

3/16″(5 mm) to 1/2″(1.3 cm) Place the deep end over the valve stem

1/2″(1.3 cm) to 3/4″(1.9 cm) Place the short end over the valve stem

Position the stem adapter onto the valve stem with the ﬂat sides

of the stem adapter as horizontal and vertical as possible.

Secure the stem adapter to the valve stem with the #8-32 x 5/8″

screw.

Align and hold the handle in the ″Off″position. Thread the

bonnet clockwise onto the retainer.

Short End

Retainer

Escutcheon

Stem Adapter

Deep End

Valve Stem

Bonnet

Handle

#8-32 x 5/8" Screw

Discard plaster

guard.

#10-24 x 3/4"

Screw

1064111-2-A 8 Kohler Co.

Guide d’installation

Baignoire mono-contrôle et garniture de

douche

INSTRUCTIONS IMPORTANTES

À LIRE ET À LAISSER AU CLIENT

AVERTISSEMENT : Risque de brûlures ou autres blessures

graves.

•Avant de commencer l’installation, l’installateur doit régler la

température maximale de l’eau de cette valve pour réduire au

minimum les risques de brûlures, ceci conformément à la norme

ASTM F 444.

•Ne pas installer un dispositif d’arrêt sur les sorties de cette valve.

L’installation d’un tel dispositif peut créer une condition de débit

croisé au régulateur et modiﬁer la température de l’eau.

•Les facteurs qui changent la température de l’eau fournie à cette

valve, tels que les changements de température d’eau saisonniers,

et le remplacement ou l’entretien du chauffe-eau, changeront la

température maximale de l’eau fournie par le régulateur et

pourront présenter un danger de brûlures. La valve à pression

réguléene compensera pas les changements de température

d’alimentation d’eau; ajuster la température maximale de cette

valve à pression équilibrée si de tels changements se produisent.

•Les valves à pression équilibrée peuvent ne pas assurer une

protection contre les brûlures en cas de défaillance d’autres

dispositifs de limitation de température installés ailleurs sur le

réseau de plomberie.

AVERTISSEMENT : Risque d’endommagement du produit.

Seuls des lubriﬁants à base de silicone devraient être utilisés

avec ces valves. L’usage de lubriﬁants à base de pétrole sur la

valve est nuisible pour les joints toriques, les étanchéités, et les

composants en plastique. L’utilisation de lubriﬁants à base de

pétrole annulera la garantie.

L’installateur est responsable de l’installation de la valve et du

réglage de la température maximale de l’eau de cette valve à pression

équilibrée conformément aux instructions.

Kohler Co. Français-1 1064111-2-A

INSTRUCTIONS IMPORTANTES (cont.)

Cette valve satisfait ou excède les exigences des normes ANSI

A112.18.1M et ASSE 1016.

S’il ne vous est pas possible de comprendre les instructions

d’installation ou de réglage de la température données par ce

document, veuillez contacter notre département du service clientèle

aux États-Unis.1-800-4-KOHLER. Hors des États-Unis, veuillez

contacter votre distributeur.

AVIS IMPORTANT AUX INSTALLATEURS! Veuillez remplir le

coupon dans le guide du propriétaire ainsi que sur l’étiquette de la

valve. Conserver le guide du propriétaire pour future référence.

Outils et matériels

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de performance. Nos numéros de téléphone

et notre adresse du site internet sont au verso. Merci encore d’avoir

choisi la compagnie Kohler.

Avant de commencer

ATTENTION : Risque de blessures corporelles. La température

de l’eau ne devrait jamais être supérieure à 120°F (49°C).

Respecter tous les codes de plomberie et de bâtiment locaux.

Le mur ﬁni ou la baignoire/douche doit être installé avant

d’installer cette garniture.

Tournevis

assortis

Clé à sangle

Mastic de

plombier

Clé hexagonale Joint en silicone

Thermomètre

Joint d'étanchéité

pour filetage

1064111-2-A Français-2 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler rada Exact-3 B Bedienungsanleitung

Kohler

Kohler MEMOIRS Series Bedienungsanleitung

Kohler

Kohler K-18865 Montageanleitung

Kohler

Kohler Leighton K-2326 Montageanleitung

Kohler

Kohler K-8207 Bedienungsanleitung

Kohler

Kohler K-7147T Bedienungsanleitung

Kohler

Kohler 77989T-8A Bedienungsanleitung

Kohler

Kohler K-6503 Bedienungsanleitung

Kohler

Kohler K-8593 Montageanleitung

Kohler

Kohler K-7114 Bedienungsanleitung

Kohler

Kohler K-8855 Bedienungsanleitung

Kohler

Kohler K-2276 Bedienungsanleitung

Kohler

Kohler K-T442 Montageanleitung

Kohler

Kohler PATIO ECO K-16321T-Y Bedienungsanleitung

Kohler

Kohler K-16010-2 Bedienungsanleitung

Kohler

Kohler STRAYT 37331A-4ND Bedienungsanleitung

Kohler

Kohler K-7437 Bedienungsanleitung

Kohler

Kohler 10-Jet K-1000-H2 Bedienungsanleitung

Kohler

Kohler K-7323 Bedienungsanleitung

Kohler

Kohler rada Thermotap-3 Bedienungsanleitung

Kohler

Kohler K-10215 Montageanleitung

Kohler

Kohler K-1896 Montageanleitung

Kohler

Kohler K-170 Montageanleitung

Kohler

Kohler K-4177 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung