Kohler K-35025-DWG Bedienungsanleitung

1551656-2-A

Installation Instructions

Record your model number:

Noter le numéro de modèle:

Anote su número de modelo:

Français, page 11

Español, página 20

Vanity

Thank You for Choosing KOHLER

Need help? Contact our Customer Care Center.

• USA/Canada: 1-800-4KOHLER (1-800-456-4537) Mexico: 001-800-456-4537

•Service parts: kohler.com/serviceparts

•Care and cleaning: kohler.com/clean

•Patents: kohlercompany.com/patents

Warranty

This product is covered under the KOHLER® One-Year Limited Warranty, found at kohler.com/warranty. For a hardcopy

of warranty terms, contact the Customer Care Center.

Tools and Materials

1/4" Drill Bit

Siliconized Acrylic Caulk

Plus:

• 2x6s

•Stud Finder

• Framing and Framing Fasteners

• Drywall and Drywall Tools

• 5/16" Lag Bolts and Washers (250 lb [113.4 kg] Load Bearing)

1551656-2-A2 Kohler Co.

Before You Begin

DANGER: Risk of electric shock. Connect only to a circuit protected by a Ground-Fault Circuit-Interrupter

(GFCI)*.

WARNING: Risk of serious or fatal injury. To avoid tipping over, the cabinet must be properly secured to the wall.

CAUTION: Risk of product damage. Do not modify the vanity. Doing so will compromise structural stability.

CAUTION: Risk of personal injury or property damage. Select 250 lb (113.4 kg) load-bearing 5/16" lag bolts with a

length to clear obstacles in the wall and 5/16" washers. Calculate the proper lag bolt length by adding the following:

1-1/2" (38 mm) backing material, plus the wallboard thickness, plus the back rail thickness.

CAUTION: Risk of product damage. Do not sit or stand on the cabinet.

CAUTION: Risk of product damage. Use care when moving the cabinet to avoid impacting, sliding, or side-

loading the legs.

NOTE: To ease installation, remove the drawer from the vanity before beginning. Refer to the "Remove/Adjust the

Drawer" section for proper removal.

NOTICE: Siliconized acrylic caulk must be used to secure a sink or countertop to the vanity. Do not use 100% silicone

sealant, which will damage the nish of the vanity.

Follow all local plumbing, building, and electrical codes.

Your product may appear dierent from the one illustrated. The installation procedure is the same.

Two people should perform this installation.

This vanity is designed to allow most base moldings to pass behind the vanity.

*Outside North America, this may be known as a Residual Current Device (RCD).

IMPORTANT HEALTH NOTICE

Some of the building materials used in this home (or these building materials) emit formaldehyde. Eye, nose, and throat

irritation, headache, nausea and a variety of asthma-like symptoms, including shortness of breath, have been reported as

a result of formaldehyde exposure. Elderly persons and young children, as well as anyone with a history of asthma,

allergies, or lung problems, may be at greater risk. Research is continuing on the possible long-term eects of exposure to

formaldehyde.

Reduced ventilation may allow formaldehyde and other contaminants to accumulate in the indoor air. High indoor

temperatures and humidity raise formaldehyde levels. When a home is to be located in areas subject to extreme summer

temperatures, an air-conditioning system can be used to control indoor temperature levels. Other means of controlled

mechanical ventilation can be used to reduce levels of formaldehyde and other indoor air contaminants.

If you have any questions regarding the health eects of formaldehyde, consult your doctor or local health department.

Kohler Co. 3 1551656-2-A

1. Prepare the Site

34-1/2" (876 mm)

2x6 Support

Back Rail

CAUTION: Risk of property damage. To properly support the weight of the vanity and vanity top/sink, secure to

stud framing or 2x6 support behind the nished wall.

Install the vanity to two or more studs, with one stud at each end of the back rail. Locate the studs and determine if

additional 2x6 support is needed.

If installing 2x6 support, install 2x6s between the wall studs at the desired vanity location. The height from the nished

oor to the top of the 2x6 support should be 34-1/2" (876 mm) and ush with the front of the wall studs.

Plan for routing supply and drain piping for your desired sink installation.

NOTICE: To verify proper support and alignment: The nished wall must be straight and plumb. The oor must be at

and perpendicular to the nished wall.

Complete the nished wall.

1551656-2-A4 Kohler Co.

2. Install the Legs and Shelf

IMPORTANT! Perform this procedure with two people.

NOTE: This vanity is intended to be installed as a oor-mount vanity. The legs must be installed.

Lay the vanity top down on a at, padded surface.

Position the leg assemblies on the boom of the cabinet so that the fastener holes line up.

Loosely aach the rst two legs with the provided hex screws, lock washers, and washers.

Place the shelf in its position, and loosely fasten the bolts, lock washers, washers, and half-circle gaskets into the rst

two legs.

Loosely aach the two remaining legs with the provided hex screws, lock washers, and washers.

Loosely fasten the remaining two sides of the shelf with the remaining two bolts, lock washers, washers, and half-circle

gaskets.

Securely tighten all four legs.

Securely tighten all four shelf bolts.

Carefully stand the vanity upright. Do not slide or side-load the legs.

Kohler Co. 5 1551656-2-A

3. Install the Vanity

Back Rail

Leveler

Washer

Lag Bolt

Pilot Hole

DANGER: Risk of electric shock. To reduce the risk of electrical shock, connect only to circuits protected by a

Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device (RCD).

CAUTION: Risk of personal injury or property damage. Select 250 lb (113.4 kg) load-bearing 5/16" lag bolts with a

length to clear obstacles in the wall and 5/16" washers. Calculate the proper lag bolt length by adding the following:

1-1/2" (38 mm) backing material, plus the wallboard thickness, plus the back rail thickness.

CAUTION: Risk of product damage. Drill the lag bolt pilot holes near the ends of the back rail to provide

maximum support and to prevent exing of the vanity.

With assistance, lift and place the cabinet in position against the nished wall. Do not slide or side-load the legs.

If the vanity has an electrical outlet, route the electrical cord to the GFCI-protected, 120 V, 15 A, grounded electrical

outlet.

Verify that the vanity is level and plumb against the wall. If necessary, turn the levelers to adjust the unit.

Using a 1/4" drill bit, drill a pilot hole through each end of the back rail and into the nished wall. Verify that the holes

align with the 2x6 support or a wall stud.

Secure the vanity to the wall with 5/16" lag bolts and washers (not provided). The lag bolts should engage the 2x6

bracing or a wall stud.

If the vanity has an electrical accessory component, plug the electrical cord into a GFCI-protected, 120 V, 15 A,

grounded electrical outlet.

1551656-2-A6 Kohler Co.

4. Remove/Adjust the Drawer

Hole

Rail

Adjustment Wheel

Latch

Hook

Adjust the Level

To adjust the position of the drawer, rotate the adjustment wheel underneath the front corners to the left or right as

needed.

Removal

Fully extend the drawer.

From underneath, press the release latches toward the sides of the drawer.

Lift the front of the drawer to disengage from the rails.

Reinstallation

Fully extend both rails.

Rest the back of the drawer onto the rails and align the rail hooks with the drawer holes.

Rotate the front of the drawer down onto the rails, engaging the latches with the rails.

Push the drawer closed to fully snap the latches into the rails and insert the rail hooks into the drawer holes.

Lightly lift the front of the drawer to verify that the drawer is fully engaged with both rails. If not engaged, repeat the

“Reinstallation” procedure.

Kohler Co. 7 1551656-2-A

5. Adjust the Door

Side-to-Side Depth

Height

Side-to-Side Adjustment

Tighten or loosen the front screw on the hinge to adjust the horizontal position of the door.

Depth Adjustment

Tighten or loosen the rear screw to adjust the depth of the door.

Height Adjustment

Remove the two front screws from the hinges.

Loosen the two rear screws in the hinges.

Slide the hinge up or down to adjust the vertical position of the door.

Tighten the two rear screws.

Install the two front screws.

1551656-2-A8 Kohler Co.

6. Install the Countertop and Sink

CAUTION: Risk of personal injury or property damage. Product can break, chip, or cause injury if handled

carelessly. Get help lifting the countertop and sink.

Install the faucet and drain following the manufacturers instructions packed with your product.

Apply a bead of siliconized acrylic caulk around the top of the vanity.

With assistance, lift the countertop and sink, set in place on top of the vanity.

Gently press down until level. Wipe away excess siliconized acrylic caulk.

Complete the faucet and drain connections.

Run water and check for leaks.

Kohler Co. 9 1551656-2-A

7. Install the Backsplash

Position the backsplash on top of the vanity and ush against the nished wall.

Verify that the sides of the backsplash are aligned with the sides of the vanity top.

Secure the backsplash using a bead of siliconized acrylic caulk on the back surface.

Firmly press the backsplash against the nished wall.

Apply a bead of siliconized acrylic caulk along the seam of the wall and backsplash.

Apply a bead of siliconized acrylic caulk along the seam of the backsplash and vanity top.

1551656-2-A10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-251 Bedienungsanleitung

Kohler

Kohler 1430508-T2-C Bedienungsanleitung

Kohler

Kohler Archer K-2359X Montageanleitung

Kohler

Kohler K-2209 Bedienungsanleitung

Kohler

Kohler K-T314 Bedienungsanleitung

Kohler

Kohler K-2277 Bedienungsanleitung

Kohler

Kohler K-368 Bedienungsanleitung

Kohler

Kohler K-T10594 Montageanleitung

Kohler

Kohler K-11608 Bedienungsanleitung

Kohler

Kohler K-8872T-2W Series Bedienungsanleitung

Kohler

Kohler VEIL HT100 TL IWT Bedienungsanleitung

Kohler

Kohler K-158 Bedienungsanleitung

Kohler

Kohler K-9310X Montageanleitung

Kohler

Kohler COMPOSED K-25421T Bedienungsanleitung

Kohler

Kohler K-4177 Bedienungsanleitung

Kohler

Kohler K-7853 Bedienungsanleitung

Kohler

Kohler K-7914 Montageanleitung

Kohler

Kohler Strayt Bedienungsanleitung

Kohler

Kohler Purist K-T97328-4-BN Bedienungsanleitung

Kohler

Kohler Centerset K-15241 Montageanleitung

Kohler

Kohler Rada T4 Series Bedienungsanleitung

Kohler

Kohler K-2746X Montageanleitung

Kohler

Kohler RiverBath Quadrangle K-1365-F2 Bedienungsanleitung

Kohler

Kohler Mira Response Handset L19A Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung