Kohler K-6506 Bedienungsanleitung

Installation Guide

Deck-Mount Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-6506 K-7982

110923-2-AB

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

Please read all instructions before you begin.

Shut off the water supply.

Observe all local plumbing and building codes.

IMPORTANT! For proper drainage of the spout, only install to a

level surface.

Before installation, unpack the new faucet trim and inspect it for

damage. Return it to the carton until installation.

For optimum performance, Kohler Co. recommends installing

3/4″high ﬂow valves connected to the spout with 5/8″Nominal

Tubing (3/4″OD).

If compression ﬁttings are used, type M, K, or L hard drawn

tubing is recommended.

Provide an access panel for all installations.

Rigid connections are recommended for this installation, however

ﬂexible hose is provided. Follow the instructions for your chosen

method of installation.

Adjustable

Wrench Tube

Cutter

Solder

Thread

Sealant Propane

Torch

Adjustable

Joint Pliers

Assorted

Screwdrivers

Plumbers

Putty

Hex

Wrenches

Long Nose

Pliers

110923-2-AB 2 Kohler Co.

Before You Begin (cont.)

To avoid potential leaks, the connections between the valves and

the spout must not be skewed.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Kohler Co. 3 110923-2-AB

1. Preparation

NOTE: The spout comes preassembled to protect the product during

shipping. The spout will need to be partially disassembled prior to

installation.

Carefully remove the plug button and O-ring from the back of the

spout.

Remove the setscrew.

Lift the spout assembly off the spout shank.

NOTE: The spout base, gasket, and spout may remain assembled.

Remove the collar, rubber washer, and ﬁber washer from the

spout shank.

Test ﬁt the spout shank to verify it will ﬁt through the hole in the

deck.

Thread a mounting nut all the way down the spout shank and

each of the handle valves.

For thin mounting surfaces, provide plywood support under the

deck.

O-Ring

Collar

Plug Button

O-Ring

Screw

Washer

Fiber Washer

Rubber Washer

Spout Shank

Mounting Nut

Setscrew

Spout

Spout Base

Gasket

110923-2-AB 4 Kohler Co.

2. Prepare the Site

Locate and mark the mounting hole locations. Mounting holes

must be a minimum of 6″(15.2 cm) center-to-center. Refer to the

roughing-in information.

Drill the mounting holes.

Install the ﬁnished deck material.

12" (30.5 cm) Min

5/8" ID

2-1/8" (5.4 cm)

Max Rough Deck

1/4" (6 mm) to

1-1/4" (3.2 cm)

Max Finished

Deck

5-11/16"

(14.4 cm) 4-5/8"

(11.7 cm)

3-1/16"

(7.8 cm)

7" (17.8 cm)

5-3/8"

(13.7 cm)

1-1/2" (3.8 cm) D.

1-5/16"

(3.8 cm) D.

Kohler Co. 5 110923-2-AB

3. Install the Shank and Valves

NOTE: This section applies to installations utilizing rigid

connections only. For installations utilizing ﬂexible connections,

proceed to the ″Install the Spout″section.

Insert the spout shank upside down through the mounting hole

in the deck.

Insert each of the valves upside down into the appropriate

mounting hole. Cold should be on the right when facing the

faucet.

Measure the distance between each of the valves and the spout

shank to determine the tubing needed for either compression

ﬁttings or solder connections. Allow for sufficient clearance.

Remove the valves and spout shank from the mounting holes.

Cut the tubing to the appropriate lengths according to your

measurements.

Preassemble the spout shank, valves, and tubing. Do not tighten

or solder any connections at this time.

Verify that the mounting nuts are still installed to the valves and

the spout shank.

Slide a ﬁber washer and then a rubber washer onto each valve

and the spout shank.

NOTE: The following steps require two people.

Measure for

tubing needed.

Bath Rim or

Mounting Surface

Spout Shank

Escutcheon

Gasket

Valve

Mounting Nut

Fiber Washer

Rubber Washer

110923-2-AB 6 Kohler Co.

Install the Shank and Valves (cont.)

Slide the spout shank/valve assembly up through the mounting

holes in the deck.

Slide a gasket onto each valve body.

Loosely secure the assembly to the deck by threading an

escutcheon onto each valve body. Verify ﬁt and make any

adjustments as needed.

NOTE: Do not install the spout or handle trim at this time.

IMPORTANT! Ensure a check valve is not installed to the spout

shank. If one is currently installed, remove it before soldering.

Solder or tighten all connections.

Kohler Co. 7 110923-2-AB

4. Install the Spout

Thread the collar onto the spout shank.

Slide the O-ring onto the spout shank.

Slip the spout base over the spout shank.

Thread the setscrew into the hole in the backside of the spout

base to secure the spout base to the shank.

Spout Assembly

NOTE: If the spout is already assembled, disregard these steps.

Set the gasket on the spout base.

Align the spout over the gasket and spout base.

Slide a washer onto each of the four screws.

With the washers in place, secure the spout to the base with the

four screws.

All Installations

Secure the spout assembly by threading the mounting nut up the

spout shank until snug.

Verify that the spout is level front-to-back and side-to-side. Make

any adjustments as needed.

Rubber

Washer

Spout

Shank

Fiber

Washer

Collar

Mounting Nut

O-Ring

Screw Washer

SideView

Setscrew

Spout Base

Gasket

O-Ring

Spout

Plug

Button

110923-2-AB 8 Kohler Co.

5. Install the Handle Valves

If utilizing rigid connections and the handle valves are already

installed, proceed to the ″Install the Handle Trim″section.

Verify that a mounting nut is threaded all the way down each of

the valve bodies.

Slide a ﬁber washer, followed by a rubber washer, down one of

the valve bodies.

From the underside of the bath rim, insert the valve up through

the mounting hole. The valve marked COLD should be installed

to the right when facing the faucet.

From above the bath, slide the gasket onto the valve body.

Thread the escutcheon onto the valve body to secure.

Repeat for the other valve.

Rubber

Washer

Fiber

Washer

Valve

Body Mounting

Nut

Escutcheon

Gasket

Kohler Co. 9 110923-2-AB

6. Install the Handle Trim

Close the valves (hot = clockwise, cold = counterclockwise).

Install a skirt over one of the valves and onto the escutcheon.

Slide a spline adapter onto the valve stem and secure with the

screw.

Position the handle assembly over the spline adapter.

Thread the skirt into the handle assembly until tight.

Repeat for the other valve.

Screw

Spline Adapter

Skirt

Valve

Stem

Handle

Assembly

Spline

Adapter

110923-2-AB 10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-5414 Betriebsanleitung

Kohler

Kohler 77989T-8A Bedienungsanleitung

Kohler

Kohler K-20099T-Y Bedienungsanleitung

Kohler

Kohler K-11660 Montageanleitung

Kohler

Kohler EVOKE 6332T-B4 Bedienungsanleitung

Kohler

Kohler K-6813 Montageanleitung

Kohler

Kohler K-3099 Montageanleitung

Kohler

Kohler K-1243 Bedienungsanleitung

Kohler

Kohler K-4108T Bedienungs- und Wartungsanleitung

Kohler

Kohler K-158 Bedienungsanleitung

Kohler

Kohler K-3607 Montageanleitung

Kohler

Kohler K-1154-HC Kurzanleitung

Kohler

Kohler PURIST UPGRADE Bedienungsanleitung

Kohler

Kohler K-514 Bedienungsanleitung

Kohler

Kohler SKYLINE Series Bedienungsanleitung

Kohler

Kohler Castia K-TS35917-4Y-2MB Bedienungsanleitung

Kohler

Kohler K-812-H2 Montageanleitung

Kohler

Kohler TOOBI 8965IN-9FP Bedienungsanleitung

Kohler

Kohler K-168 Bedienungsanleitung

Kohler

Kohler STRAYT 37331A-4ND Bedienungsanleitung

Kohler

Kohler K-20257T-CP Bedienungsanleitung

Kohler

Kohler BRIVE+ K-8703IN-1WH Bedienungsanleitung

Kohler

Kohler K-7147T Bedienungsanleitung

Kohler

Kohler PINOIR K-2015 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung