Kohler K-20257T-CP Bedienungsanleitung

所有的资料是按最新出版的产品资料编写而成。

科勒公司保留任何时候不经通知即可改变产品特

性、包装或产品可供类型的权利。

说明书包括重要的安装、保养及清洁方面的内容，

请把这些资料交给用户阅读。

Composed Sensor Faucet

柏诗台盆感应龙头（单冷型/不含电源盒/0.5GPM）

COMPOSED SENSOR FAUCET COLD ONLY(W/O P)0.5GPM

柏诗台盆感应龙头-典雅黑（单冷型/不含电源盒/0.5GPM）

COMPOSED SENSOR FAUCET COLD ONLY(W/O P)2BZ

柏诗台盆感应龙头-罗曼银（单冷型/不含电源盒/0.5GPM）

COMPOSED SENSOR FAUCET COLD ONLY(W/O P)BN

柏诗台盆感应龙头-玫瑰金（单冷型/不含电源盒/0.5GPM）

COMPOSED SENSOR FAUCET COLD ONLY(W/O P)RGD

柏诗台盆感应龙头（单冷型/不含电源盒/0.35GPM）

COMPOSED SENSOR FAUCET COLD ONLY(W/O P)0.35GPM

柏诗台盆感应龙头（单冷型/不含电源盒/0.26GPM）

COMPOSED SENSOR FAUCET COLD ONLY(W/O P)0.26GPM

柏诗台盆感应龙头（冷热混合型/不含电源盒/0.5GPM）

COMPOSED SENSOR FAUCET MIXER(W/O P)0.5GPM

K-20257T-CP

K-20257T-2BZ

K-20257T-BN

K-20257T-RGD

K-20257T-S3-CP

K-20257T-S5-CP

K-20258T-CP

安装之前

1.一定要先彻底冲洗供水管以清除管道中的杂质,

使用水源为自来水或可供饮用水。

2. 请勿将强力及冲击施于产品，以免造成故障，

引起漏水。

3. 安装、清洁龙头时，切勿损伤感应窗口表面，

以免造成故障。

4. 如果是安装新的洗面盆，可将水龙头和排水组

件先安装到面盆上。

NOTES:

注意事项:

All information is based on the latest product information

available at the time of publication, Kohler Co. reserves the

right to make changes to product characteristics, packaging,

or availability at any time without notice. Please deliver these

instructions for the consumer. They contain important

installation, maintenance and cleaning information.

1. Flush the water supply pipes thoroughly to remove debris.

Faucet is designed for tap water or potable water.

2. Handle the faucet with care to avoid damaged.

3. Do not damage the surface of sensing window when

installing or cleaning the faucet.

4. For new installations, install the faucet and drain to the

lavatory before installing the lavatory.

BEFORE YOU BEGIN

1298747-T01-B

科勒（中国）投资有限公司

中国上海市闸北区江场三路158号邮编：200436

制造商：上海科勒电子科技有限公司

中国上海市宝山区丰翔路1955号邮编:200444

柏诗

COMPOSED

1298747-T01-B

维修交流龙头时，必须断开交流电源并关闭

水源。

12.Turn off the electrical source and shut down water

supply before servicing faucet.

1. 手伸到出水口下方感应范围

内（感应距离随面盆、周围的情

况而自动调节），水龙头出水。

手离，0.5～1秒，水龙头自动止

水。

使用说明 OPERATING INSTRUCTIONS

2. 冷热混水龙头水温调节：先

关闭热水角阀，再将冷水角阀旋

至冷水最大状态，再缓慢打开热

水角阀，以免烫伤。如冷水水压

大，打开全部热水角阀后，仍无

合适水温，请再缓慢减少冷水出

水量，直至水温使用舒适。

Place your hands under the faucet within the

sensor range ( the sensor range will auto-adjust

to its surroundings , the faucet should be on.)

The faucet will automatically turn off after 0.5~1

second after moving your hands away from the

sensor. The sensing distance will be adjusted

automatically per the condition of the lavatory

and surrounding environment.

Adjust the water temp for faucet with

temperature mixture: turn off hot water valve

first, and then turn on the water and adjust to full

cold, slowly turn on hot water valve to avoid

scalding. If cold water pressure is high and

unable to gain proper comfortable water temp

even hot water valve is fully open, turn down

cold water capacity slowly until water temp is

comfortable for use.

可搭配脸盆

CAN BE MATCHED LAVATORY

K-2660T-1 拂朗长方形时尚脸盆

K-14715T-1 派丽蒙半嵌入式台盆

K-5026-1 瑞芙1000mm一体化台盆

K-2749T-1 拂朗900mm一体化台盆

K-2748T-1 拂朗1200mm一体化台盆

K-18571T 瑞琦1050mm一体化台盆

K-18572T 瑞琦700mm一体化台盆

K-2764T-1 皓时尚脸盆

K-2264T 苔丝修边式台上台盆

K-2759T-1 皓修边式台上台盆

K-2351T-1 希玛龙修边式台上台盆

K-2660T-1 FOREFRONT™ Vessel

K-14715T-1 PARLIAMENT™ Semi-Recessed Lavatory

K-5026-1 REVE® 1000mm Vanity

K-2749T-1 FOREFRONT™ 900mm Vanity

K-2748T-1 FOREFRONT™ 1200mm Vanity

K-18571T REACH™ 1050mm Vanity

K-18572T REACH™ 700mm Vanity

K-2764T-1 KARESS® Vessel

K-2264T CENTERPIECE™ Self-rimming Lavatory

K-2759T-1 KARESS® Self-rimming Lavatory

K-2351T-1 CIMARRON® Self-rimming Lavatory

对于冷热混水龙头，先将连接热水的角阀关

闭，以免烫伤。

修理面盆时，用黑色电工胶布粘住感应窗口。

10.For faucet with temperature mixer, please turn off valve

before connecting to hot water to avoid scalding.

11.Cover the sensing window with black tape when repairing

lavatories.

6. For electric connection on AC faucets, carefully follow the

installation instructions provided. Only provide to the electric

power box after the installation is conpleted.

7. Only install a maximum of two faucets to one AC/DC

transformer.

8. Ensure electrical source is fitted with a suitable fuse to

protect AC/DC transformer unit from damage.

9. Do not put the faucet near strong ultraviolet or

electromagnetic field.

5. As for DC type faucets, please pay special attention to

insert direction matches battery poles. Tighten the battery

cover completely to prevent its exposure to moisture.

5. 对于直流龙头，安装时注意电池的正负极不能

装反，电池盒盖要拧紧，防止电池受潮。

6. 对于交流龙头，安装时务必按照说明书的要求

正确连接导线，龙头安装完毕后才可向电源盒供

电。

7. 一个交流电源盒最多可供两个感应龙头。

8. 交流电的总电源必须有合适熔断丝加以保护。

请勿使产品感应窗口靠近强紫外线或电磁场。

11.

12.

10.

K-99184T

K-2210T

K-2211T

K-2214X

K-97012T

K-97011T

可搭配脸盆（续）

CAN BE MATCHED LAVATORY(Continued)

1.如果使用非推荐的脸盆，可能会产生

2.不适合不锈钢脸盆。

注意：

溅水在脸盆外面或感应异常等情况；

K-2330-G KATHRYN® 17'' Under Counter Lavatory

K-2297 KATHRYN® 21'' Under Counter Lavatory

K-2889T VERTICYL® Rectangular Under Counter Lavatory

K-2883 VERTICYL® Round Under Counter Lavatory

K-2882 VERTICYL® Rectangle Under Counter Lavatory

K-2881T VERTICYL® Oval Under Counter Lavatory

K-2949T FOREFRONT™ Under Counter Lavatory

K-2319 BANCROFT® Under Counter Lavatory

K-2215T-M LADENA® Under Counter Lavatory

K-2751T CIMARRON® Under Counter Lavatory

K-2336T DEVONSHIRE® Under Counter Lavatory

K-99184T CHALICE™ Under Counter Lavatory

K-2210T CAXTON® 17'' Under Counter Lavatory

K-2211T CAXTON® 19'' Under Counter Lavatory

K-2214X LADENA 21'' Under Counter Lavatory

K-97012T CHALICE 21'' Under Counter Lavatory

K-97011T CHALICE 16'' Under Counter Lavatory

安装尺寸(毫米) ROUGH-IN DIMENSIONS(mm)

柏诗台盆感应龙头

（直流电/冷热混合型）

柏诗台盆感应龙头

（直流电/单冷型）

K-2330-G

K-2297

K-2889T

K-2883

K-2882

K-2881T

K-2949T

K-2319

K-2215T-M

K-2751T

K-2336T

1298747-T01-B

凯瑟琳17"台下台盆

凯瑟琳21"台下台盆

维克长方形台下台盆

维克圆形台下台盆

维克长方形台下台盆

维克椭圆形台下台盆

拂朗台下台盆

贝卡夫台下脸盆

拉蒂纳台下盆

希玛龙台下台盆

蒂梵诗台下台盆

乔司台下台盆

卡斯登17"台下台盆

卡斯登19"台下台盆

拉蒂纳21"台下台盆

乔司21"椭圆形台下台盆

乔司16"圆形台下台盆

Whole metope Whole metope

193 193

148 148

123 140 123 140

51 51

NOTE:

1.Use of a non-recommended lavatory may result in water

spillage outside of the lavatory or will cause the poor

sensing problem；

2.Can't use stainless steel lavtory.

Drain

排水组件

φ41.2

φ54

φ31.75

226

φ66.5

16305T-NA

AC/DC Transformer

交流电源盒

Output: DC6V

输出:直流电压6V

Input: AC220V

输入:交流电压220V

安装尺寸(毫米)(续） ROUGH-IN DIMENSIONS(mm)

(Continued)

1298747-T01-B

24484T-NA

DC Power Unit

直流电源盒

直流电压6V

Output: DC6V

注：直流或交流电源盒需另购。 NOTE:DC Power or AC/DC transformer need purchasing.

Whole metope Whole metope

193 193

148 148

123 140 123 140

51 51

AC/DC transformer

交流电源盒

AC/DC transformer

交流电源盒

柏诗台盆感应龙头

（交流电/冷热混合型）

柏诗台盆感应龙头

（交流电/单冷型）

INSTALLATION

安装步骤

一龙头与面盆的安装固定

将固定螺杆(2)安装到水龙头(1)底部

处。再把垫片(3)套在固定螺杆上。并

嵌入水龙头底部的盘槽中。然后将电

源线(7)和出水软管(8)穿过安装孔，

从面盆下方将固定橡胶垫片(4)固定金

属垫片(5)和固定螺母(6)对齐固定螺

杆向上套入。调整水龙头电源线及出

水软管的位置。用扳手拧紧固定螺母

以便把水龙头固定在面盆上。

How to Install the Faucet

技术参数

电源：直流 4节5号碱性电池(LR06×4)

交流电压220V,频率50/60Hz

检测时间：小于0.5秒

关阀延时：0.5～1秒

感应距离：自动调节

流量：

环境温度：1～55

进水温度：0.5～71

适用水压：0.05～

0.86MPa

TECHNICAL SPECIFICATION

Power: DC 4 pieces of AA size alkaline batteries

AC 220V, 50/60Hz

Senser Duration: Less than 0.5s

Shut-off Delay: 0.5~1s

Sensing Distance: Automatic adjustment

Flow Rate:

Overtime Flowing Control: Automatically stop flushing

when the faucet senses an object for more than 1 minute

continuously

Ambient Temperature: 1~55

Supply Water Temperature: 0.5~71

Supply Water Pressure: 0.05~0.86MPa

℃

如何安装水龙头

二安装控制组件

拧下控制盒盖(10)螺钉(11)，打开控制

盒(9)，根据安装尺寸图（图一）在墙

壁合适的位置钻孔，打入膨胀管

(12)，使控制盒紧贴墙面，再用螺钉

(13)将其固定在墙壁上。

注意：控制盒长边端需竖直放置，出

水口位置可根据需要左右调整。

对于冷热混水龙头，将软管(16)一端与

三通进水软管组件(17)连接，另一端与

控制组件(15)进水口连接，再将出水口

与龙头出水软管(8)连接，三通进水软

管组件另外两端与角阀(18)连接。

图一

Secure faucet on lavatory

Install the stud (2) to the underside of the

faucet (1). Slide the gasket (3) over the

stud, and then seat the gasket in the groove

on the underside of the sprout. Cross power

cord (7) and water outlet hose (8) through

mounting hole, slide rubber washer (4),

metal washer (5) and nut (6) onto the stud

from under the sink. Adjust faucet power

cord and water outlet hose position, fasten

nut to secure faucet on lavatory mounting

surface by wrench.

Install Control Assy

Unscrew valve cover screw (11) with a

screwdriver and open valve cover (10).

Determine proper mounting location per

rough –in (Fig 1), then punch expansion

tube (12) in. Place valve box against the

wall and then secure control valve

assembly on the wall by bolts (13).

Note: Place the long end of control box

upright, water outlet position shall be

adjusted left/right based on requirements.

For mixture faucet, connect hose (16)

to Tee water inlet hose assembly(17),

and then connect water outlet with

faucet water outlet hose (8). Connect

Tee water inlet hose other two ends

with valve (18).

For cold water faucet, connect hose

to the cylinder(19) and then connect

with valve.

1298747-T01-B

0.5GPM About 1.9L/min

0.35GPM About 1.4L/min

0.26GPM About 1.0L/min

0.5GPM 约1.9L/min

0.35GPM 约1.4L/min

0.26GPM 约1.0L/min

超时用水控制：超时用水1分钟，自动止水。

对于单冷龙头，将软管(16)一端与滤网

接头组件(19)相连，另一端与角阀连接

即可。

℃

1298747-T01-B

三安装直流电源盒

1. (20)

15 17

混水(Mixer)

(21)

1. Take battery box out, loosen screws

4节5

单冷(Cold)

注意：

2. Connect power cords with

四如何安装排水组件 4

(22）22

(23)

Apply plumbers putty 23

(22)Screw the drain flange ( 22) into drain

body (23). Tighten the locknut (24)

manually from the underside.

Note: Remove excessive putty. Note:

after tightening locknut (24), do not

adjust drain body position, otherwise

putty seal might be damaged.

(24)

(25)(26)

25mm 55mm

Connect the tailpiece( 25) to the

trap(26). The tailpiece should ex tend

25mm to 55mm into the trap.

Note:

Ensure cylinder install on water inlet.

Install DC Power Unit

(20), insert 4 AA batteries per +/-

pole indication ( 21) on battery

box cover. Fasten battery box

cover with screws.

Note: no reversed battery

polarity. Do not mix new and used

batteries together.

corresponding color wires, then place

battery box assembly to empty space

within control assembly then fasten

control box by screws based on

installation direction. For AC faucet,

except corresponding cords connect to

AC/DC transformer output, other

installation methods are identical.

How to Install the Drain

Unscrew the drain flange ( 22) from

drain assembly. Apply plumbers

putty around the bottom circle. Insert

drain body (23) into lavatory from the

underside.

(23)

(24)

注意：

感应龙头

AC/DC transformer

交流电源盒

接220V交流电

Connect AC 220V

Switch

开关

Wire Tube

穿线管

Faucet

一个交流电源盒供一个感应龙头

如何安装交流电源盒

Connect to

electrical Source

接交流电源

注意：禁止将交流AC220V接入直流DC接线端。

Connect to

Faucet

接感应龙头

Connect to

electrical Source

接交流电源

Connect to

Faucet

接感应龙头

Faucet

感应龙头

Faucet

感应龙头

AC/DC transformer

交流电源盒

接220V交流电

Connect AC 220V

Switch

开关 Wire Tube

穿线管

HOW TO INSTALL THE AC/DC

TRANSFORMER

One AC/DC transformer supply one touchless faucet

一个交流电源盒供两个感应龙头

One AC/DC transformer supply two touchless faucets

Note: Do not connect AC 220V electrical source directly to DC connector.

注：交流电源盒需另购。 NOTE:AC/DC transformer need purchasing

1298747-T01-B

HOW TO CHANGE TO A MIXING SENSOR

FAUCET (If customerpurchases tee inlet

assy. 1298710-SP)

三通进水软管组件

用户自备角阀外螺纹

如何转换成混水感应龙头

若用户另购三通进水软管

组件1298710-SP）

1. ( )

0.5mm

0.3mm

AC power unit (sticker on the back) should be

installed in a dry place away from water. Customer

should prepare wire tube and wire according to their

requirement. Wire tube should be mounted into the wall.

Suggested wire: AC connection wire adopts wires with

protecting layer or sleeve and the section should

be ≥ 0.5mm . The section of DC connection wire

should be ≥ 0.3mm . The connection pattern must

follow the illustrations above.

2.After wire layout finished, check and repair if needed.

Then connect AC connector to AC connector within

FPC pipe, DC connect or (black-orange) on electrical

box to faucet power cord connector (wire from valve

box). Finally turn on AC power source.Faucet will

commence auto-sense mode which will take 2 minutes.

The faucet will not work during this period.

( )

AC 2分钟

Tee , Inlet Assy

1298747-T01-B

如何转换成恒温阀感应龙头

(若用户另购

恒温阀16294T-3-CP,

具体安装详见其说明书

)

接感应龙头

Connect Sensor Faucet

注：三通、角阀请用户自备。

墙面

Wall

墙面

Wall

1. 感应指示灯的各种闪烁情况

感应指示灯是使用者了解感应龙头有效、唯一

的途径。所以明白了感应指示灯闪烁所代表的

含义，可以正确使用感应龙头，

IMPORTANT CONSUMER INFORMATION

清理说明

适用于所有加工处理过的表面，以中性肥皂水清

洗镀层表面，再以干净的软布彻底擦干整个表

面。许多清洁剂，比如氨水，去污粉及洁厕灵

等，会对电镀表面造成伤害，切忌使用。

有腐蚀性的清洁剂或溶剂不可使用于科勒的水龙

头及其配件上。

用户须知

安装结果检查

检查并确保所有衔接处都已拧紧，打开排水系统

和主要供水源，检查并修理有漏水的接口。

恒温阀

thermostatic valve

角阀

Stop Valve

角阀

Stop Valve

三通

Tee

三通

Tee

出水口

Outlet 三通

Tee

进热水

hot

进冷水

cold

INSTALLATION CHECKLIST

Check and ensure that all connections are tight. Open the

drain. Turn on main water supply and check for leaks.

Repair leakage when necessary.

CLEANING INSTRUCTIONS

Applicable for all finishes: clean the finish with a mild soap.

Wipe entire surface completely dry with a clean soft cloth.

Most cleaners may contain chemicals, such as ammonia,

chlorine, toilet cleaner etc. which could adversely affect the

finish and are not recommended for cleaning. Do not use

abrasive cleaners or solvents on Kohler faucets and

fittings.

1. Light indicator Key

HOW TO CHANGE TO A THERMOSTATIC

SENSOR FAUCET (If users purchased the

thermostatic valve 16294T-3-CP, please refer to

the installation guide 16294T-3-CP)

MIN 50mm

Note: Please prepare the tee and stop valve accordingly.

The indicator is the only and effective way to learn the

faucets working conditions. So the users can use the

sensor faucet correctly with knowing the meaning of the

sensor indicator's flashing.

1298747-T01-B

用户须知（续）

如图示:

(1) 快速闪烁，代表感应龙头正处于通电后

的两分钟自动调节阶段。期间，安装者、使

用者不得干扰其自动调节，感应范围内不要

放置物体。

(2) 间隔6秒钟闪烁一次（直流版本），表

示电池即将使用完，请更换电池。

(3)

间隔2秒钟连续闪烁：若直流感应龙头,

代表龙头电池耗尽，已停止工作，等待使

用者更换电池;若交流感应龙头，表示为两

种情况：一种为刚刚停电；另一种为在交

流供电正常的情况下，则电源盒直流接线

端接触不良。

IMPORTANT CONSUMER INFORMATION

(Continued)

超时出水控制

连续在感应状态下使用约一分钟，龙头自动止水。

自动止水后，手或物体离开感应范围后，再次进

入感应范围内，龙头正常工作，否则无反应。

指示灯

Indicator Light

3. 清洗过滤系统 Clean the Filtration System

该感应龙头的控制组件内已包含了过

滤装置。如管内杂质过多或水质较

差，长期使用会引起出水情况不良。

请按以下步骤清洗过滤装置：

2. 将控制组件进水口处软管拧下，取

出滤网组件，用水冲洗完毕后，重新

装入。

When the faucet flows continuously for 1 minute, the

faucet will automatically stop.Objects must be removed

from the sensing range. Then the water will flow when

objects re-enter into the sensing range again. Otherwise,

the faucet will not work.

2. Timeout setting

1. 关闭角阀。

The touchless faucet control assembly include

filtration device. Poor water outflow shall be

caused by excessive impurities inside the hose

or poor water quality after long time use. Please

clean filtration device per following steps:

Turn off stop valve.

Pull hose from control assembly water inlet,

take filter screen assembly out. Reinstall screen

after clean by water.

As shown:

(1) Quick flashing means the faucet is in the

period of adjusting sensing distance after power

on for 2 minutes. During these 2 minutes, please

do not disturb auto adjustment or place objects

within the sensing range.(2) The indicator flashes

every 6 seconds (DC type) indicates that the unit is

out of battery and has stopped working. Replease

batteries.

(3) The indicator flashes every 2s: as for DC type

faucets, this indicates the unit is out of battery and

ceases working. Please replace batteries. For AC

faucet, it indicates two possibilities: one is that the

unit is out of battery; or poor DC terminal contact

under normal AC power supply.

(4) Under normal condition, the water will flow and

the indicator will flash once when objects are

detected. (The indicator does not flash when

faucet stops flowing.)

滤网组件

滤网组件 2.

(4) 在正常工作情况下，当有物体被感

应时，龙头出水，感应指示灯闪烁一

次。(龙头关闭，感应指示灯不闪烁）

混水(Mixer)

单冷(Cold)

1298747-T01-B

4. 自动清洗存水功能 4.

When the faucet is no used for a long period of

time, it will automatically flush to discharge the

stagnant water inside the faucet every 24hrs.

感应龙头长期处于不使用状态时，

每间隔24小时自动冲水一段时间排

出龙头内的存水。

Self-Cleaning the stagnant water

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-15003 Bedienungsanleitung

Kohler

Kohler K-1418-G Kurzanleitung

Kohler

Kohler Stance 14775-4-CP Montageanleitung

Kohler

Kohler Tableau K-14293 Bedienungsanleitung

Kohler

Kohler K-10086 Montageanleitung

Kohler

Kohler CARE K-22779T-1 Bedienungsanleitung

Kohler

Kohler COMPOSED K-EX34060T Bedienungsanleitung

Kohler

Kohler Vessels Bedienungsanleitung

Kohler

Kohler MINIMA K-45803T-L-SHP Bedienungsanleitung

Kohler

Kohler 528D Bedienungsanleitung

Kohler

Kohler K-454 Montageanleitung

Kohler

Kohler K-1954 Montageanleitung

Kohler

Kohler K-7397 Bedienungsanleitung

Kohler

Kohler Castia K-TS35917-4Y-2MB Bedienungsanleitung

Kohler

Kohler K-75449-BN Bedienungsanleitung

Kohler

Kohler Flipside 15596T Bedienungsanleitung

Kohler

Kohler VOLUTE K-18669T Bedienungsanleitung

Kohler

Kohler ALTERNA Bedienungsanleitung

Kohler

Kohler K-302 Bedienungsanleitung

Kohler

Kohler K-T72770 Montageanleitung

Kohler

Kohler BodySpa K-1030 Bedienungsanleitung

Kohler

Kohler K-3393 Montageanleitung

Kohler

Kohler 72695T-B4 Bedienungsanleitung

Kohler

Kohler K-4108 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung