Kohler K-514 Bedienungsanleitung

Installation Guide

Alcove Bath Whirlpool

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de Mcorresponden a México

(Ej. K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-513, K-514 K-723, K-724 K-783, K-784

K-809 K-856

1019484-2-C

Important Information

WARNING: When using electrical products, basic precautions should always be followed, including

the following:

DANGER: Risk of electric shock. Connect only to circuits protected by a Ground-Fault

Circuit-Interrupter (GFCI) or Earth-Leakage Circuit-Breaker (ELCB).

Building materials and wiring should be routed away from the pump body and other heat-producing

components of the unit.

Install to permit access for servicing.

A pressure wire connector marked ″Earth/Ground″is provided within the wiring compartment. To reduce

the risk of electric shock, connect this connector to the grounding terminal of your electric service or supply

panel with copper wire equivalent in size to the circuit conductor supplying this equipment.

Pressure wire connectors are provided on the exterior of the junction box or control within this unit to permit

connection of a bonding conductor between this unit and all other exposed metal in the vicinity, as needed to

comply with local requirements.

Grounding is required. The unit should be installed by a qualiﬁed service representative, and grounded.

WARNING: Risk of electric shock. A licensed electrician should make all electrical connections.

WARNING: Risk of electric shock. Disconnect power before servicing.

WARNING: Risk of injury or property damage. Please read all instructions thoroughly before

beginning installation, including the following requirements.

NOTICE: Follow all local plumbing and electrical codes.

Product Information

Electrical Requirements

The installation must have a Class A Ground-Fault Circuit-Interrupter (GFCI) or Earth-Leakage

Circuit-Breaker (ELCB). The GFCI or ELCB protect against line-to-ground shock hazard. Use a 220 - 240 V, 20

A, 50/60 Hz dedicated service for the whirlpool.

Product Notices

WARNING: Unauthorized modiﬁcation may cause unsafe operation and poor performance of the

whirlpool. Do not relocate the whirlpool pump, or make other modiﬁcations to the whirlpool system,

as this could adversely affect the performance and safe operation of the whirlpool. Kohler Co. shall not

be liable under its warranty or otherwise for personal injury or damage caused by any such

unauthorized modiﬁcation.

Features

Components include a pump, heater, control and illuminated switch (user keypad).

The whirlpool pump and piping are factory-assembled.

Connections and Service Access

Before installation, ensure proper access to the ﬁnal connections.

1019484-2-C 2 Kohler Co.

Product Information (cont.)

NOTICE: Provide generous, unrestricted service access to the pump. You must provide access for

servicing the pump and controls. The access must be located immediately next to the pump. Study the

roughing-in information packed with the whirlpool.

Table of Contents

Important Information .............................................................. 2

Product Information ............................................................... 2

Electrical Requirements .......................................................... 2

Product Notices ................................................................ 2

Features ..................................................................... 2

Connections and Service Access ................................................... 2

Thank You For Choosing Kohler Company .............................................. 3

Before You Begin ................................................................. 4

Tools and Materials ............................................................... 4

Prepare the Site ................................................................. 5

Prepare the Site ................................................................. 6

Prepare the Whirlpool ............................................................. 6

Install the Whirlpool ............................................................... 7

Cut the Pump Banding Straps ....................................................... 7

Install the Plumbing ............................................................... 8

Make Electrical Connections ......................................................... 8

Install the Whirlpool Trim Kit ......................................................... 9

Test Run the Whirlpool ............................................................. 9

Complete the Finished Wall ........................................................ 10

Complete the Concrete Installation ................................................... 10

Clean-Up After Installation ......................................................... 10

Conﬁrm Proper Operation .......................................................... 11

Operating Sequence .............................................................. 11

Troubleshooting Procedures ........................................................ 11

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few minutes to review this manual before

you start installation. If you encounter any installation or performance problems, please don’t hesitate to

Company.

Kohler Co. 3 1019484-2-C

Before You Begin

WARNING: Risk of personal injury. Your cast iron whirlpool is extremely heavy. Obtain sufficient

help to carefully lift and move it.

CAUTION: Risk of product damage. Do not lift the whirlpool by the piping or pump, or use the

piping or pump for structural support of the whirlpool.

We recommend this whirlpool for alcove installation.

Inspect the whirlpool for damage before you begin installation.

You must install this whirlpool to an adequately supported, level subﬂoor.

Tools and Materials

Plus:

• Conventional woodworking or concrete

installation tools and materials

• Drop cloth

• Metal shims

• 2x4's

Silicone Sealant Measuring Tape Pencil Tin Snips Level

Safety Glasses Pipe Wrench

1019484-2-C 4 Kohler Co.

1. Prepare the Site

Concrete Construction

NOTICE: Adequate ﬂoor support must be provided. Consult the roughing-in sheet packed with your

whirlpool for speciﬁc ﬂoor loading requirements.

CAUTION: Risk of product damage. Do not support the whirlpool by the rim.

Make sure the ﬂooring offers adequate support for your whirlpool, and verify that the subﬂoor is

ﬂat and level.

The whirlpool should be installed in an alcove installation (a two wall installation is also

acceptable).

Install an access panel to allow the pump to be serviced.

Construct brick or concrete supports. When installing with two walls, the supports on the ﬂanged

side of the whirlpool should rise to the top of the ﬂange.

Position the plumbing according to the roughing-in information packed. Cap the supplies, and

check for leaks.

Brick

Bath

1/16"

(2 mm)

Tile

Approved

Tile Backing

Tile

Approved Tile Backing Brick

Raise the sidewall to the

height of the flange.

Install an access panel to allow

the pump to be serviced.

TwoWall Installation

Alcove Installation Typical

access

panel

Typical

access

panel

Kohler Co. 5 1019484-2-C

2. Prepare the Site

Wood Construction

NOTICE: Adequate ﬂoor support must be provided. Consult the roughing-in sheet packed with your

whirlpool for speciﬁc ﬂoor loading requirements.

CAUTION: Risk of product damage. Do not support the whirlpool by the rim.

Make sure the ﬂooring offers adequate support for your whirlpool, and verify that the subﬂoor is

ﬂat and level.

The whirlpool should be installed in an alcove installation. Construct 2x4 stud framing designed for

your particular installation in accordance with the roughing-in information packed with the

whirlpool.

Install an access panel to allow the pump to be serviced.

Position the plumbing according to the roughing-in information. Cap the supplies, and check for

leaks.

3. Prepare the Whirlpool

Install the drain to the whirlpool according to the drain manufacturer’s instructions. Do not connect

the trap at this time.

Position a clean drop cloth or similar material in the bottom of the whirlpool. Be careful not to

scratch the surface of the whirlpool.

Typical access

panel

Construct 2x4

stud framing

according to

roughing-in

information.

Verify that the subfloor

offers adequate support,

and is flat and level.

Position the

rough plumbing.

1019484-2-C 6 Kohler Co.

4. Install the Whirlpool

WARNING: Risk of personal injury. This cast iron whirlpool is extremely heavy. Obtain sufficient help

to carefully lift and move it.

CAUTION: Risk of product damage. Do not lift the whirlpool by the piping or pump, or use the

piping or pump for structural support of the whirlpool.

CAUTION: Risk of product damage. Do not support the whirlpool by the rim.

Carefully move the whirlpool into position. Insert the drain tailpiece into the trap.

Level the whirlpool by ﬁtting metal shims under the whirlpool feet as needed. Check for level along

the top of the whirlpool, and across the drain side. If the feet are not accessible from the back or

side, move the whirlpool in and out of position to shim it properly. Make sure the whirlpool is

resting on all four feet.

5. Cut the Pump Banding Straps

IMPORTANT! This step is necessary to make your Kohler whirlpool operate more quietly.

Use tin snips to cut the two pump banding straps from the whirlpool pump.

NOTE: Do not raise the pump higher than it was before you cut the pump banding straps. If the pump is

raised too high, it will not prime properly. Make sure the rubber isolation feet are in place.

To minimize whirlpool noise and vibration, be sure the pump is not in direct contact with the

shipping bracket after the pump banding straps are cut. The pump control contains rubber isolation

feet to reduce pump noise.

Level by fitting metal shims

under the whirlpool feet.

Pump

Wiring

Harness

Rubber Isolation Feet

Control

Cut the pump banding straps.

Kohler Co. 7 1019484-2-C

6. Install the Plumbing

CAUTION: Risk of property damage. Ensure a watertight seal on the whirlpool drain.

Connect the drain to the trap according to the drain manufacturer’s instructions.

NOTICE: An access panel will simplify future maintenance.

Install the faucet valving according to the faucet manufacturer’s instructions. Do not install the

faucet trim until instructed. Open the hot and cold water supplies, and check the supply

connections for leakage.

Run water into the whirlpool, and check the drain connections for leakage.

7. Make Electrical Connections

NOTE: The whirlpool model number is printed on a label near the whirlpool pump. This label also

identiﬁes the electrical rating of the whirlpool. All whirlpools come equipped with a wiring junction box

and will only operate at 220 V through 240 V and at 50 Hz or 60 Hz.

WARNING: Risk of electric shock. To reduce the risk of electric shock, connect the pump to a

properly grounded Ground-Fault Circuit-Interrupter (GFCI) or Earth-Leakage Circuit-Breaker (ELCB).

This will provide additional protection against line-to-ground shock hazard. A 220 - 240 V, 20 A, 50/60

Hz dedicated circuit is required.

WARNING: Risk of electric shock. Make sure the power has been disconnected before performing the

following procedures.

The whirlpool controls and system have been prewired at the factory. A licensed electrician should

make a routine service connection to the junction box.

Connect service to the junction box. The junction box contains blue, brown and green with a yellow

stripe colored wires and a ground lug.

Provide a separate equipment earthing conductor for the earth lug located inside the junction box.

The earthing conductor must not be connected to any current-carrying conductor. Follow local

electrical codes. Bond in accordance with national and local codes.

A wiring harness has been prewired at the factory, allowing communication between the keypad, all

features, and the control. No additional wiring is required, but ensure that all wires are securely

fastened.

NOTE: Your wiring harness includes an antenna for the optional remote control. Do not alter or damage

this antenna during installation.

Ground (Green with

Yellow Stripe)

Blue

Supply 60 Hz 50 Hz From Control

L1 L1 Brown

L2 N Blue

Electrician to

provide suitable

strain relief.

The junction box should be

wired as shown. Bond in accordance with

national and local codes.

Wire

Connectors

From Control

Brown

Heater (models may

vary) T-style (shown)

or inline (not shown)

Heater Electrical Cord

Wiring

Harness

Junction

Box Control

Pump

Electrical

Cord

1019484-2-C 8 Kohler Co.

8. Install the Whirlpool Trim Kit

Install the whirlpool trim kit according to the instructions packed with the trim kit. Pay particular

attention to the jet installation steps below - they are very important and are included here to help

you obtain smooth, trouble-free jet operation.

NOTE: The jet O-ring must be correctly positioned, must be lubricated, and must be in good condition to

permit easy rotation and proper operation of the jet.

Install the O-ring onto the ﬁrst shoulder of the jet. Lubricate the O-ring with silicone lubricant to

prevent noisy operation of the jet.

Carefully insert the jet into the housing, and lightly push and rotate the jet until it snaps into

position. Do not force the jet.

NOTE: When installed correctly, the jet should turn smoothly both clockwise and counterclockwise.

9. Test Run the Whirlpool

Check all electrical connections, and make sure the electrical power to the whirlpool is turned on.

Make sure all union connections to the pump and heater are securely hand tightened.

Verify that the pump banding straps have been cut, and that the pump control is resting directly on

the subﬂoor. Ensure that the rubber isolation feet are in place.

Fill the whirlpool to a level at least 2″(5.1 cm) above the top of the highest jet.

Operate the whirlpool for 5 minutes (refer to the ″Operating Sequence″section) and check all

whirlpool piping connections, on the back side, for leaks.

For additional information on whirlpool operation, see ″Conﬁrm Proper Operation″section.

Slide the O-Ring

onto the first

shoulder of the jet.

Inspect and

lubricate the

O-Ring.

Insert the jet into the housing,

and lightly push and rotate

until it snaps in position.

Housing

Kohler Co. 9 1019484-2-C

10. Complete the Finished Wall

If you have not already done so, carefully remove any protective tape from the whirlpool rim.

Cover the framing with water-resistant wall material. Seal the joints between the whirlpool rim edge

and the water-resistant wall material with silicone sealant.

Tape and mud the water-resistant wall material. Install the ﬁnished wall to the water-resistant wall

material so it is 1/16″(2 mm) above the enameled surface. Seal the joints between the whirlpool rim

and the ﬁnished wall material with silicone sealant.

Install the faucet trim according to the instructions packed with the trim.

11. Complete the Concrete Installation

If you have not already done so, carefully remove the protective tape from the whirlpool rim.

Apply mortar and tile to the wall, deck and surround material as needed.

Apply a bead of sealant where the tile meets the whirlpool surface.

Install the faucet trim according to the instructions packed with the trim.

12. Clean-Up After Installation

When cleaning up after installation, do not use abrasive cleansers, as they may scratch and dull the

whirlpool surface. If necessary, use warm water and a liquid detergent to clean the surface of the

whirlpool, user keypad and remote control.

Remove stubborn stains, paint, or tar with turpentine or paint thinner. Do not allow cleaners

containing petroleum distillates to remain in contact with any whirlpool surfaces for long periods

of time. Remove plaster by carefully scraping with a wood edge. Do not use metal scrapers, wire

brushes, or other metal tools. Use a powder-type detergent on a damp cloth to provide mild

abrasive action to any residual plaster.

Water-Resistant

Wall Material

Stud Framing or

Concrete Wall

Apply silicone sealant to the

joint between the whirlpool

and the finished wall.

Install the finished wall

material 1/16" (2 mm)

above the enameled

surface.

Whirlpool

1019484-2-C 10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-6811 Montageanleitung

Kohler

Kohler Sterling 7613 Series Bedienungsanleitung

Kohler

Kohler Primary K-4321 Bedienungsanleitung

Kohler

Kohler K-5329 Montageanleitung

Kohler

Kohler Sterling 225C7 Montageanleitung

Kohler

Kohler K-18865 Bedienungsanleitung

Kohler

Kohler 10-Jet K-1000-H2 Bedienungsanleitung

Kohler

Kohler KUMIN K-18655T-B-CP Bedienungsanleitung

Kohler

Kohler Elate 13963X-4 Bedienungsanleitung

Kohler

Kohler K-T16225 Bedienungsanleitung

Kohler

Kohler Clearflo K-7160 Bedienungsanleitung

Kohler

Kohler Corbelle Comfort Height Revolution 360 ContinuousClean... Bedienungsanleitung

Kohler

Kohler STANCE K-37467T Bedienungsanleitung

Kohler

Kohler 8022A Bedienungsanleitung

Kohler

Kohler K-2529 Montageanleitung

Kohler

Kohler K-2096 Bedienungsanleitung

Kohler

Kohler 32E Bedienungsanleitung

Kohler

Kohler K-4918 Montageanleitung

Kohler

Kohler PATIO ECO K-16321T-Y Bedienungsanleitung

Kohler

Kohler K-45471X Montageanleitung

Kohler

Kohler 13900T-4 Bedienungsanleitung

Kohler

Kohler 1114111 Bedienungsanleitung

Kohler

Kohler K-690 Bedienungsanleitung

Kohler

Kohler K-7179 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung