Kohler K-72218 Montageanleitung

Installation and Care Guide

Electronic Kitchen Faucet

K-72218 K-99332

1186051-2-F

IMPORTANT INSTRUCTIONS

WARNING: When using electrical products, basic

precautions should always be followed, including the

following:

DANGER: Risk of electric shock. Connect only to a circuit

protected by a Ground-Fault Circuit-Interrupter (GFCI)*.

WARNING: Risk of electric shock. Grounding is required. A

licensed electrician should make all electrical connections.

WARNING: Risk of electric shock. Disconnect power before

servicing.

WARNING: Risk of injury or property damage. Please read

all instructions thoroughly before beginning installation.

CAUTION: Risk of property damage. The faucet spout

contains a magnet. Do not allow items susceptible to

electromagnetic damage to come into close proximity to the

spout.

Follow all plumbing, electrical, and building codes.

*Outside North America, this device may be known as a Residual

Current Device (RCD).

Tools

Important Information

WARNING: Risk of fresh water contamination. This faucet

contains back-siphonage protection. Do not remove any

internal components.

3/8"

Phillips Screwdriver Bucket

Plus:

• Unswitched Electrical Outlet

Rags

1186051-2-F 2 Kohler Co.

Important Information (cont.)

CAUTION: Risk of product damage. This product contains

sensitive electronic components. Do not store open containers of

chemical or cleaning products near this product. Cleaning rags or

sponges must be rinsed with fresh water before storage.

IMPORTANT! Do not use a switch-controlled outlet (typically used

for garbage disposals) to provide power to the faucet.

Observe all local plumbing and building codes.

Provide a constant unswitched 120 VAC electrical outlet located

below the sink within 5’ (1.5 m) of the control box.

Turn off the water supply.

For new installations, assemble the faucet to the sink before

installing the sink.

For uneven mounting surfaces (such as tile grout lines), apply a

suitable sealant under the faucet. Do not use petroleum-based

sealant.

Kohler Co. 3 1186051-2-F

1. Install the Faucet

NOTE: Handle orientation is designed to be on the right.

Thread the screws into the ring 1/4″(6 mm) past the surface.

Insert the faucet through the mounting surface with the handle

on the right.

Pull the sprayhead out and rest it in the sink basin. Do not pull

the end of the spray hose into the shank.

From under the sink, push the spray hose up to the shank.

Slide the washer over the hoses and wires, then up onto the

shank.

Slide the ring over the hoses and wires, then up to the shank.

Thread the ring onto the shank until the washer contacts the

underside of the sink.

Adjust the ring to align the screws with the front and back of the

faucet.

Use a Phillips screwdriver to securely tighten the screws.

Pull the spray hose end down, away from the shank.

Slide the sprayhead back into the spout.

Escutcheon

Washer

Ring

1/4"

(6 mm)

Shank

Spray

Hose

1186051-2-F 4 Kohler Co.

2. Connect the Hoses

CAUTION: Risk of restricted water ﬂow and product damage.

Supply hoses must not be taut, kinked, or twisted during

installation. If the supply hoses must be coiled, maintain an inside

diameter of 3″(76 mm).

Connect the Supplies

Assemble the outlet hose to the faucet.

Connect and tighten the supply hoses to the supply stops.

Place a bucket under the outlet hose.

Turn on the water supplies.

Flush hot and cold water into a bucket for 1 minute to remove

any debris.

Connect the Spray Hose

Remove the protective cap.

NOTE: The weight must be installed onto the spray hose to act as a

pull stop and to prevent kinking damage.

Solenoid

Clamp

Weight

Outlet Hose

Ø 3" (76 mm)

Min

Supply

Hose

Kohler Co. 5 1186051-2-F

Connect the Hoses (cont.)

Slide the weight, then the clamp onto the spray hose.

NOTE: Use a pliers to expand the clamp over the hose end.

Attach the spray hose to the outlet ﬁtting on the solenoid. Ensure

the hose is completely engaged into the ﬁtting.

1186051-2-F 6 Kohler Co.

3. Install the Solenoid

CAUTION: Risk of restricted waterﬂow. The outlet hose

must not be taut or kinked when installed. Locate the

solenoid valve within 7″(178 mm) to 8″(203 mm) of the

faucet centerline.

NOTE: Locate the solenoid valve within 7″(178 mm) to 8″(203

mm) from the faucet centerline. Allow adequate clearance for

servicing.

Mount the Bracket

NOTE: The mounting bracket should be secured with two suitable

fasteners (not supplied) based on the type and thickness of the

cabinet or wall material.

Fasten the mounting bracket vertically to the cabinet or wall.

Connect the Wires

NOTE: The solenoid may be positioned to the right or left. Remove

the appropriate tab on the cover.

Apply grease.

Solenoid

Wire

LED

Mounting

Bracket

Handle Switch

Solenoid

Tab

Power

Cord

Sensor

Cover

Solenoid

Kohler Co. 7 1186051-2-F

Install the Solenoid (cont.)

Apply grease (provided) to the sensor socket located on the

circuit board inside the cover. This will provide additional

corrosion protection.

Connect the handle switch wire and sensor wire from the faucet

to the circuit board.

Connect the power cord to the circuit board.

Connect the solenoid wire to the circuit board.

Plug the power cord into an unswitched 120 VAC outlet. The

LED on the circuit board will illuminate.

Test activation of the sensor. Refer to the ″Faucet Operation″

section.

Fit the cover over the solenoid.

Secure the assembly to the mounting bracket with the two screws

provided.

1186051-2-F 8 Kohler Co.

4. Complete the Installation

Position the Weight

Position the weight between 2″(51 mm) and 3″(76 mm) from the

cabinet ﬂoor.

Secure the clamp around the spray hose just below the weight.

Extend and retract the spray hose to check for smooth operation.

Check for Leaks

Ensure all connections are tight.

Turn on the water supplies, and check all connections for leaks.

Test the faucet for proper operation. Refer to the ″Faucet

Operation″section.

2" (51 mm) –

3" (76 mm)

Kohler Co. 9 1186051-2-F

Faucet Operation

Rotate the handle outward to the open position to start water

ﬂow. The handle LED will illuminate to indicate that the sensor is

functioning.

Adjust the handle to the desired water temperature.

Wave your hand under the spout to turn the water OFF.

Wave your hand under the spout again to restart the water ﬂow.

NOTE: Some objects that are clear and certain colors are not

detectable by the sensor. Always use your hand for sensor testing.

If needed, refer to the ″Handle LED Adjustment″section for more

information.

NOTE: For extended periods of nonuse, the handle should be

returned to the closed (upright) position. The handle LED will turn

OFF, indicating that water ﬂow is not available.

LED Indicators

Handle LED: Illuminates when the sensor is active.

Circuit board LED: Indicates there is power to the circuit board.

NOTE: The sensor LEDs are only visible inside the spout when the

spray hose is extended.

Green sensor LED: Indicates there is power to the sensor.

Sensor

Open Position

Manual Override

Handle LED

Sensor

LEDs

1186051-2-F 10 Kohler Co.

Andere Handbücher für K-72218

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K1044435 Handbuch

Kohler

Kohler K-7179 Montageanleitung

Kohler

Kohler Refinia K-T5324 Montageanleitung

Kohler

Kohler K-7167 Montageanleitung

Kohler

Kohler Mira Sport J03A Bedienungsanleitung

Kohler

Kohler BOTTICELLI 2393-WH Bedienungsanleitung

Kohler

Kohler COUTURE ECO-LITE Bedienungsanleitung

Kohler

Kohler K-T309 Bedienungsanleitung

Kohler

Kohler STERLING 996 Bedienungsanleitung

Kohler

Kohler K-10481 Bedienungsanleitung

Kohler

Kohler K-23984T-0 Bedienungsanleitung

Kohler

Kohler 23776T-7 Bedienungsanleitung

Kohler

Kohler K-6558 Bedienungsanleitung

Kohler

Kohler Margaux Series Bedienungsanleitung

Kohler

Kohler K-T461 Bedienungsanleitung

Kohler

Kohler 8881T-VC01-BN Bedienungsanleitung

Kohler

Kohler Wave 72687X-4 Bedienungsanleitung

Kohler

Kohler C3-150 Montageanleitung

Kohler

Kohler 1114111 Bedienungsanleitung

Kohler

Kohler K-9142 Bedienungsanleitung

Kohler

Kohler K-7779 Bedienungsanleitung

Kohler

Kohler Revival K-2950-1/8 Bedienungsanleitung

Kohler

Kohler 8002A Bedienungsanleitung

Kohler

Kohler Cyan K-705788 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung