Kohler Symbol Rite-Temp K-T18488 Bedienungsanleitung

Installation Guide

Single-Control Bath and Shower Trim

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-T18488 K-T18489

K-T18490

1054205-2-B

IMPORTANT INSTRUCTIONS

WARNING: Risk of scalding or other severe injury.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

•Do not install a shut-off device on either outlet of this valve. The

installation of any such device may create a cross-ﬂow condition

at the valve and affect the water temperature.

•Factors that change the temperature of the water supplied to the

valve, such as seasonal water temperature changes, and water

heater replacement or servicing, will change the maximum water

temperature supplied by the valve and may create a scalding

hazard. The pressure-balanced valve will not compensate for

changes in the water supply temperature; adjust the maximum

water temperature setting of this pressure-balanced valve when

such changes occur.

•Pressure-balanced valves may not provide protection against

scalding if there is a failure of other temperature-limiting devices

elsewhere in the plumbing system.

WARNING: Risk of product damage. Only silicone based

lubricants should be used with these valves. Use of petroleum

based lubricants on the valve is harmful to the O-rings, seals,

and plastic components. Use of petroleum based lubricants will

void the warranty.

The installer is responsible for installing the valve and adjusting the

maximum water temperature of this pressure-balanced valve

according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the installation or temperature

adjustment instructions in this document, in the United States please

contact our Customer Service Department at 1-800-4-KOHLER.

Outside the U.S., please contact your distributor.

IMPORTANT NOTICE TO INSTALLERS! Please ﬁll in the blanks in

the information box in the Homeowners Guide and on the valve label.

Retain the Homeowners Guide for future reference.

1054205-2-B 2 Kohler Co.

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

Observe all local plumbing and building codes.

The ﬁnished wall or bath/shower unit must be installed prior to

installing this trim.

Before installing the trim, determine if the maximum water

temperature is acceptable to the user. If temperature adjustment is

needed, refer to the valve manufacturer’s instructions to properly

adjust the water temperature.

The valve shuts off by water pressure. Do not force the handle in

any direction. To turn the valve off, gently turn it to the ″OFF″

position.

Shut off the main water supply.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

Thermometer

Strap

Wrench Thread

Sealant

Silicone

Sealant Plumbers

Putty

Assorted

Screwdrivers

Plus:

• 1/2" NPT Pipe Nipple

Kohler Co. 3 1054205-2-B

1. Install the Spout

Remove the temporary nipple.

Apply thread sealant and install a 1/2″nipple so it extends 7/16″

(1.1 cm) beyond the ﬁnished wall.

Apply a bead of plumbers putty or other sealant around the inlet

end of the spout according to the manufacturer’s instructions.

Apply thread sealant to the nipple and thread the spout onto the

nipple.

Carefully tighten with a clean strap wrench.

Remove any excess putty.

1/2" Nipple

7/16"

(1.1 cm)

Apply plumbers

putty.

1054205-2-B 4 Kohler Co.

2. Install the Showerhead Assembly

CAUTION: Risk of product damage. To avoid clogging the

showerhead spray outlets, use thread sealant tape on the pipe

nipple. Do not use thread sealant compound (pipe dope).

Remove the temporary nipple from the shower elbow.

Apply thread sealant and install a 1/2″NPT nipple to extend 1″

(2.5 cm) beyond the ﬁnished wall.

Turn the main water supply on.

Run water through the pipe nipple to ﬂush out dirt and debris.

Place the wall ﬂange onto the pipe nipple and ﬂush against the

wall.

Apply thread sealant tape to the pipe nipple, then thread the

showerhead assembly onto the pipe nipple.

Carefully tighten the showerhead assembly to the pipe nipple

with a clean strap wrench.

Showerhead

Assembly

Wall Flange

Pipe Nipple

Shower Elbow

Kohler Co. 5 1054205-2-B

3. Optional Temperature Limiting Adjustment

CAUTION: Risk of personal injury. The water temperature

should never be set above 120°F (49°C).

NOTE: Do not remove the O-ring and collar at this time. Removing

the O-ring and collar will change the factory setting for the

maximum water temperature.

Turn the valve clockwise to the full open position and let the hot

water run for several minutes. Position a thermometer in the

water stream and check the temperature.

For minor water temperature changes, adjust the setscrew, and

recheck the water temperature.

For major water temperature changes, remove the O-ring and

collar from the valve stem. Slowly rotate the valve stem until the

desired maximum water temperature is reached.

Reinstall the collar on the valve stem with the setscrew against

the side of the tab.

Reinstall the O-ring, rotate the valve stem counterclockwise to

shut the water off.

Recheck the water temperature.

Complete the information on the valve label (if supplied).

O-Ring

Setscrew

Tab

Collar

Setscrew

Valve

Label

Standard

Valve

High Flow

Valve

Stem

1054205-2-B 6 Kohler Co.

4. Install the Diverter Assembly

Remove and discard the plaster guard and/or dome, if installed.

Position the actuator over the diverter stem. Tighten the setscrew.

Slide the guide over the actuator and thread it onto the diverter

stem.

Guide

Setscrew

Actuator

Diverter Assembly

Valve

Stem

Diverter

Stem

Discard plaster

guard with dome.

Kohler Co. 7 1054205-2-B

5. Install the Trim

Remove and discard the plaster guard and/or dome from the

valve stem, if installed.

For wall thickness of 3/16″(5 mm) to 7/16″(1.1 cm): Attach the

retainer to the valve stem with the #10 screws provided.

For wall thickness of 7/16″(1.1 cm) to 3/4″(1.9 cm): Place the

spacer onto the valve stem, then attach the retainer to the valve

stem with the #10 screws provided.

Install the faceplate onto the retainer. The cutout on the faceplate

should face downward.

Install the pivot ring to the faceplate, and rotate clockwise to lock

in place. The pivot ring should be situated with the cutout

aligned with the faceplate cutout.

Rotate the valve stem fully counterclockwise to the ″OFF″

position.

Position the deep end of the stem adapter onto the valve stem.

The outer sides of the stem adapter should be positioned as

horizontal and vertical as possible.

Attach the stem adapter with the supplied screw.

Ensure the O-ring is positioned in the groove on the inside of the

handle assembly.

Align the handle to the ″OFF″position. Hold the handle in the

″OFF″position and thread the handle assembly securely onto the

retainer.

Discard dome.

Spacer Retainer

Screws

Faceplate

Pivot Ring

Stem Adapter

Screw

O-Ring

Handle Assembly

Valve Stem

1054205-2-B 8 Kohler Co.

Install the Trim (cont.)

Apply a bead of silicone sealant around the sides and top of the

faceplate.

Kohler Co. 9 1054205-2-B

Guide d’installation

Baignoire mono-contrôle et garniture de

douche

INSTRUCTIONS IMPORTANTES

AVERTISSEMENT : Risque de brûlures ou autres blessures

graves.

•Avant de commencer l’installation, l’installateur doit régler la

température maximale de l’eau de cette valve pour réduire au

minimum les risques de brûlures, ceci conformément à la norme

ASTM F 444.

•Ne pas installer un dispositif d’arrêt sur les sorties de cette valve.

L’installation d’un tel dispositif peut créer une condition de débit

croisé au régulateur et modiﬁer la température de l’eau.

•Les facteurs qui changent la température de l’eau fournie à cette

valve, tels que les changements de température d’eau saisonniers,

et le remplacement ou l’entretien du chauffeau, changeront la

température maximale de l’eau fournie par le régulateur et

pourront présenter un danger de brûlures. La valve à pression

réguléene compensera pas les changements de température

d’alimentation d’eau; ajuster la température maximale de cette

valve à pression équilibrée si de tels changements se produisent.

•Les valves à pression équilibrée peuvent ne pas assurer une

protection contre les brûlures en cas de défaillance d’autres

dispositifs de limitation de température installés ailleurs sur le

réseau de plomberie.

AVERTISSEMENT : Risque d’endommagement du produit.

Seuls des lubriﬁants à base de silicone devraient être utilisés

avec ces valves. L’usage de lubriﬁants à base de pétrole sur la

valve est nuisible pour les joints toriques, les étanchéités, et les

composants en plastique. L’utilisation de lubriﬁants à base de

pétrole annulera la garantie.

L’installateur est responsable de l’installation de la valve et du

réglage de la température maximale de l’eau de cette valve à pression

équilibrée conformément aux instructions.

Cette valve satisfait ou excède les exigences des normes ANSI

A112.18.1M et ASSE 1016.

Kohler Co. Français-1 1054205-2-B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-6330 Bedienungsanleitung

Kohler

Kohler K-29221T Series Bedienungsanleitung

Kohler

Kohler FLIGHT NEUS E62C70-00 Bedienungsanleitung

Kohler

Kohler HiRise K-7344-4 Montageanleitung

Kohler

Kohler Mira Event XS Bedienungsanleitung

Kohler

Kohler K-16012-4 Bedienungsanleitung

Kohler

Kohler K-7304 Montageanleitung

Kohler

Kohler K-5805 Montageanleitung

Kohler

Kohler Devonshire 193-4-2BZ Bedienungsanleitung

Kohler

Kohler K-997 Bedienungsanleitung

Kohler

Kohler K-5814 Bedienungsanleitung

Kohler

Kohler Kumin K-104K37-SANA-CP Bedienungsanleitung

Kohler

Kohler BRAZN K-702242T Bedienungsanleitung

Kohler

Kohler K-10094 Montageanleitung

Kohler

Kohler 10868T-B4 Bedienungsanleitung

Kohler

Kohler 10879T-4 Bedienungsanleitung

Kohler

Kohler ODEON K-8711T Bedienungsanleitung

Kohler

Kohler PARALLEL K-31139T-4-BL Bedienungsanleitung

Kohler

Kohler K-6227 Montageanleitung

Kohler

Kohler K-10085 Montageanleitung

Kohler

Kohler K-5415 Bedienungsanleitung

Kohler

Kohler URBANITY 23748T-9 Bedienungsanleitung

Kohler

Kohler Stance 14787A Bedienungsanleitung

Kohler

Kohler K-7827 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung