Kohler K-4108 Bedienungsanleitung

Installation Guide

Bidet Seat with Remote Control

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (e.j.

K-12345M)

Français, page “Français-1”

Español, pagina “Español-1”

K-4108

1194356-2-A

Important User Information

READ ALL INSTRUCTIONS BEFORE

INSTALLING THIS PRODUCT

IMPORTANT! Risk of product damage. Do not supply electrical

power to the unit until the plumbing installation work has been

completed; it could cause the product to malfunction.

NOTE: The thermal protectors may trip during storage or

transportation in warm weather causing the unit to not operate.

Allow the unit to cool to room temperature before installation or

operation.

Grounding Instructions

•This product should be grounded. In the event of an electrical

short circuit, grounding reduces the risk of electric shock by

providing an escape wire for the electric current. This product is

equipped with a cord having a grounding wire with a grounding

plug. The plug must be plugged into an outlet that is properly

installed and grounded.

DANGER: Risk of electric shock. Improper use of the

grounding plug can result in a risk of electric shock.

•If repair or replacement of the cord or plug is necessary, do not

connect the grounding wire to either ﬂat blade terminal. The wire

with insulation having an outer surface that is green with or

without yellow stripes is the grounding wire.

•Check with a qualiﬁed electrician or service personnel if the

grounding instructions are not completely understood, or if in

doubt as to whether the product is properly grounded.

1194356-2-A 2 Kohler Co.

Tools and Materials

Before You Begin

WARNING: Risk of electric shock, ﬁre, or personal injury.

This product must be grounded. Connect only to a dedicated

120 VAC, 60 Hz circuit protected by a minimum 15 A

Ground-Fault Circuit-Interrupter (GFCI) or Residual Current

Device (RCD).

WARNING: Risk of electric shock. Do not immerse or ﬂush

the product with water.

CAUTION: Risk of property damage. Damaged water

connections may leak. Do not push or pull on the water

connection between the seat and the water supply stop.

NOTICE: To avoid possible product malfunction, do not plug in the

seat until instructed to do so.

NOTICE: Do not install this seat in a location where: (1) water

might be splashed on the product or (2) excessive moisture, high

humidity levels, or condensation are present. This will avoid

damage to the electronic components.

NOTICE: Do not use an extension cord with this product.

Observe all local plumbing, electrical, and building codes.

Only connect the seat to a cold water supply of drinking quality

water at a pressure of 20 (139 kPa) - 80 psi (551 kPa).

Plastic Wrap

Adjustable

Wrench

Pencil 1/16", 1/4"

Kohler Co. 3 1194356-2-A

1. Install the Electrical Outlet

WARNING: Risk of electric shock, ﬁre, or personal injury.

This product must be grounded and connected only to a

dedicated, nominal 120 VAC, 60 Hz circuit protected by a

minimum 15 A Ground-Fault Circuit-Interrupter (GFCI) or

Residual Current Device (RCD).

NOTICE: This product is factory equipped with a speciﬁc electrical

cord and plug to permit connection to a proper electric circuit. Make

sure that the product is connected to an outlet having the same

conﬁguration as the plug. Do not modify the plug provided – if it

will not ﬁt the outlet, have the proper outlet installed by a qualiﬁed

electrician. If the product must be reconnected for use on a different

type of electric circuit, the connection should be made by qualiﬁed

service personnel.

NOTICE: Consult your local electrical codes before determining the

connection type and the electrical outlet location. The temporary

connection may not be permitted by local electrical codes and the

electrical outlet location may be speciﬁed.

NOTICE: To avoid possible product malfunction, do not plug in the

seat until instructed to do so.

Preferred Connection

NOTE: Do not use an extension cord.

Cover Screw

Adapter

Temporary ConnectionPreferred Connection

Grounding

Screw Tab

12"

(305 mm)

Grounding Pin

1194356-2-A 4 Kohler Co.

Install the Electrical Outlet (cont.)

Determine the electrical outlet location. Locate the electrical outlet

within 12″(305 mm) of the toilet.

IMPORTANT! Do not plug the seat into the electrical outlet at this

time.

Install and ground the electrical outlet. This electrical outlet must

be a dedicated, nominal 120 VAC, 60 Hz circuit protected by a

minimum 15 A Ground-Fault Circuit-Interrupter (GFCI) or

Residual Current Device (RCD).

Temporary Connection

NOTICE: Unless the outlet cover screw is grounded through the

house wiring, attaching the adapter grounding screw tab to the

cover screw will NOT ground the unit. If there is any doubt

whether the cover screw is grounded, have it checked by a qualiﬁed

electrician or service professional.

A temporary connection with a two-prong adapter may be made

where local codes permit, provided the adapter is grounded.

Kohler Co. 5 1194356-2-A

2. Site Preparation

If applicable, remove the existing toilet seat.

Turn off the water supply to the toilet.

Flush the toilet to relieve any pressure from the water supply

hoses.

Disconnect the water supply hose from the toilet ﬁll valve.

Determine the installation location for the remote control docking

station.

Docking Station

36"

(914 mm)

38" (965 mm) - 66" (1676 mm)

1194356-2-A 6 Kohler Co.

3. Install the Docking Station

Position the back plate at the desired mounting location.

Conﬁrm the back plate is level.

Using a pencil, mark the two mounting hole locations. Set the

back plate aside.

For installation into a stud or other wood surface: Drill a 1/16″

hole at each of the marked locations.

For installation using wall anchors: Drill a 1/4″hole at each of

the marked locations. Install the wall anchors into the holes.

Remove the adhesive strip cover on the back plate.

Position the back plate over the anchors or marks, adhesive side

toward the wall. Secure the back plate with the screws.

Open the battery compartment. Install four AA batteries in the

compartment in the back of the docking station.

Position the docking station on the back plate.

Position the remote control on the docking station.

1/16"

or 1/4"

Holes

Back Plate

Remote Control

Docking Station

Batteries

Kohler Co. 7 1194356-2-A

4. Install the Mounting Plate

NOTE: Inspect the toilet seat mounting holes for threaded inserts.

Follow the steps applicable to your mounting hole type.

For Toilets with Threaded Inserts

Position the mounting plate over the mounting holes on the bowl.

Insert a bolt through each washer.

Insert each bolt through the mounting plate and mounting hole,

into the threaded inserts.

Position the washers to rest in the grooves of the mounting plate.

Loosely thread the bolts into the inserts. The bolt must be loose

enough to allow the seat to be adjusted.

For All Other Installations

Position the mounting plate over the mounting holes on the bowl.

Insert each bolt through the mounting plate and into the

mounting holes.

Position the washers to rest in the grooves of the mounting plate.

Loosely thread a nut onto each of the bolts. The nut must be

loose enough to allow the seat to be adjusted.

Mounting Plate

Bolt

Washer

Nut

1194356-2-A 8 Kohler Co.

5. Install the Seat and Hose

Position the Seat

Slide the seat onto the mounting plate until you feel it snap into

place.

Check the positioning of the seat. Adjust the position if needed.

Adjust the Seat

To adjust the seat position, remove the seat by pressing the

release button in and sliding the seat forward.

Reposition the mounting plate as needed.

Install the Seat

Securely tighten the mounting plate bolts.

Install the seat.

Install the Hose

IMPORTANT! Risk of product damage. Do not cross-thread the

hose-to-seat connection.

Connect the supply hose to the bidet seat. Do not overtighten.

Use the supplied clips to attach the power cord and supply hose

to each other.

Mounting Plate

Release Button

Clips

Hose

Clips

Kohler Co. 9 1194356-2-A

6. Connect the Water Supply

CAUTION: Risk of property damage. Do not push or pull

on the water connection between the seat and the water

supply stop. This will prevent water leakage.

NOTICE: Use care to avoid cross threading or overtightening the

connections. Use an adjustable wrench to tighten one-quarter turn

past hand-tight.

Connect the T-valve to the bidet hose.

If needed, connect the supply hose to the supply stop.

Connect the supply hose to the T-valve.

Conﬁrm the gasket is in place in the T-valve. Install if needed.

Connect the T-valve to the water inlet on the toilet tank.

Turn on the water supply.

Check all connections for leaks and make any adjustments as

needed.

Hose

Gasket

T-Valve

Supply Stop

Supply Hose

1194356-2-A 10 Kohler Co.

Andere Handbücher für K-4108

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-13142 Montageanleitung

Kohler

Kohler K-1002-H2 Montageanleitung

Kohler

Kohler HYDRO-TOWER 200 Series Bedienungsanleitung

Kohler

Kohler K-6881 Montageanleitung

Kohler

Kohler C3-225 K-4736T-0 Bedienungsanleitung

Kohler

Kohler K-470 Montageanleitung

Kohler

Kohler K-15599X Bedienungsanleitung

Kohler

Kohler STANCE Bedienungsanleitung

Kohler

Kohler K-5805 Montageanleitung

Kohler

Kohler K-596D Bedienungsanleitung

Kohler

Kohler ESCALE Bedienungsanleitung

Kohler

Kohler Quiet-Close C3-455 Bedienungsanleitung

Kohler

Kohler K-14660 Montageanleitung

Kohler

Kohler Sterling 446124 Bedienungsanleitung

Kohler

Kohler K-10121 Bedienungsanleitung

Kohler

Kohler Mira Escape Thermostatic 9.0 kW J95Hb/c Bedienungsanleitung

Kohler

Kohler K-5814 Montageanleitung

Kohler

Kohler Archer VibrAcoustic K-2595-VBW Bedienungsanleitung

Kohler

Kohler K-16250 Montageanleitung

Kohler

Kohler OVE Bedienungsanleitung

Kohler

Kohler K-20099T-Y Bedienungsanleitung

Kohler

Kohler K-444 Montageanleitung

Kohler

Kohler PURIST Series Bedienungsanleitung

Kohler

Kohler K-4919 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung