Kohler K-994 Bedienungsanleitung

Installation Guide

Floor-Mount Bath Faucet

Français, page “Français-1”

Español, página “Español-1”

K-994 K-10129

1144501-2-D

Tools

Important Information

WARNING: Risk of personal injury. Do not use the bath

ﬁller as a grab bar or support bar when entering or exiting

the bath. The bath ﬁller is not designed to support weight.

NOTICE: To avoid damage to the O-rings on the bottom of the

faucet, keep the faucet vertical and use care when installing the

faucet.

Observe all local plumbing and building codes.

Shut off the main water supply.

A drill bit is provided for installation to wood support. A

different drill bit is required for concrete ﬂoor installations; this

bit is not provided.

The dimensions given assume the spout and bath are mounted on

the same surface. Adjust the dimensions accordingly if the spout

and bath are mounted on different surfaces.

If this product is installed with an overﬂowing bath, the outer rim

of the bath should slightly overlap the 2x4 framing.

Installer supplied copper tubing must be 5/8″OD (1/2″

Nominal).

Carefully review this document and any appropriate rough-in

sheets. Design the bath enclosure accordingly.

The appearance of your faucet may differ from the illustrations in

this guide. The instructions still apply.

Sealant Tape

Pencil

Phillips Screwdriver

Tape Measure

Level

Drill

1144501-2-D 2 Kohler Co.

1. Prepare the Site

NOTICE: Adequate ﬂoor support is required. The wood support

must be a minimum of 2″(51 mm) thick by 6″(152 mm) wide. 2x6

lumber is NOT adequate for this application.

26-3/8"

(670 mm) Min

27-3/16"

(691 mm)

Max

5-13/16"

(148 mm)

2" (51 mm) Min

2-3/4" (70 mm) Max

7-7/8"

(200 mm) Min

3-3/8"

(86 mm) Min

Finished

Wall

Finished

Floor

Joist

2" (51 mm) Min

6" (152 mm) Min

Floor

Joist

Wood Support

6" (152 mm) Min Width

Kohler Co. 3 1144501-2-D

1. Spout Orientation

When performing this installation:

Verify correct spout orientation before securing the base to the

ﬂoor.

Connect the faucet to the base with screws and washers through

the ﬂange. Orient the spout to the inside of the bath.

Rotate the base if necessary by loosening the screws to verify the

supplies are in line with the base inlet connections. You may have

to modify the supply lines if necessary.

The cold supply should be connected where the blue mark or the

notch is located.

Test the handle to verify full rotation will not interfere with the

bathing ﬁxture or the back wall.

Inside of Bath

Finished Floor

1144501-2-D 4 Kohler Co.

2. Install the Base

Locate the position on the wood support where the base will be

installed. Use the base as a guide to mark the mounting hole

locations.

Drill 1-1/2″(380 mm) deep holes with a 3/16″drill bit (provided)

using the marked locations as the center point.

Secure the base to the support with the screws and washers

provided.

Verify the base is level and tighten the screws.

Washer

Screw

Ø 3/16"

Mounting Hole

Wood Support

Floor Joist

Base

Kohler Co. 5 1144501-2-D

3. Connect the Supplies

Apply sealant tape on the ½″NPT hot and cold supply pipes and

thread into the base.

NOTE: The base has a blue mark and a notch on the cold supply

side.

Insert the plug into the base.

Turn on the main water supply and check for leaks.

Turn off the main water supply.

Secure the guard onto the base with the screws provided.

Guard

Screw

Plug

Hot Supply

Cold Supply

Notch

Base

1144501-2-D 6 Kohler Co.

4. Install the Finished Floor

Finish the ﬂoor leaving a 3″(76 mm) diameter hole for the guard.

Cut the guard so it is ﬂush with the ﬁnished ﬂooring.

Finished Floor

Guard

Ø 3" (76 mm)

Kohler Co. 7 1144501-2-D

5. Install the Faucet

NOTICE: To avoid damage to the O-rings on the bottom of the

faucet, keep the faucet vertical and use care when installing the

faucet.

Remove the plug from the base.

Remove the rubber protector (not shown) from the faucet.

Place the faucet onto the base and insert the screws and washers

provided through the ﬂange. Tighten the screws using the hex

wrench provided.

Escutcheon

Hex

Wrench

Screw

Flange

O-Rings

Plug

Base

Washer

1144501-2-D 8 Kohler Co.

6. Install the Handshower

Remove the rubber protector (not shown) from the diverter and

install the hose.

Install the hose to the handshower and place into the holder.

Diverter

Handshower

Holder

Handshower

Screen

Washer

Hose

Gasket

Kohler Co. 9 1144501-2-D

7. Installation Checkout

Ensure the faucet handle is in the OFF position.

Turn on the main water supply and check for leaks.

Remove the aerator from the spout.

Remove the handshower from the hose.

Point the hose into the bath and turn the faucet handle to the ON

position.

Pull down on the handshower diverter to send water through the

hose to remove debris.

Push the handshower diverter up.

Run hot and cold water through the spout to remove debris.

Check for leaks.

Turn the faucet off.

Reinstall the aerator and the hose. Place the handshower into the

handshower holder.

Washer

Insert

Aerator

Handshower

Holder

Handle

Handshower

Diverter

1144501-2-D 10 Kohler Co.

Andere Handbücher für K-994

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler 15343 Series Bedienungsanleitung

Kohler

Kohler MINIMA K-45803T-L-SHP Bedienungsanleitung

Kohler

Kohler K-2746X Montageanleitung

Kohler

Kohler K-6946 Bedienungsanleitung

Kohler

Kohler K-5026 Montageanleitung

Kohler

Kohler K-8855 Bedienungsanleitung

Kohler

Kohler K-T944 Montageanleitung

Kohler

Kohler K-7166-AF Montageanleitung

Kohler

Kohler K-13132 Bedienungsanleitung

Kohler

Kohler Cantata K-2199 Bedienungsanleitung

Kohler

Kohler MODERN LIFE K-21842T Bedienungsanleitung

Kohler

Kohler K-352 Bedienungsanleitung

Kohler

Kohler K-6490 Bedienungsanleitung

Kohler

Kohler K-1188BR Bedienungsanleitung

Kohler

Kohler K-T10278 Montageanleitung

Kohler

Kohler K-6227 Montageanleitung

Kohler

Kohler K-7401 Montageanleitung

Kohler

Kohler VEIL HT100 TL IWT Bedienungsanleitung

Kohler

Kohler K-8807 Bedienungsanleitung

Kohler

Kohler 3867T Bedienungsanleitung

Kohler

Kohler WaterTile K-8030 Montageanleitung

Kohler

Kohler K-T16229 Bedienungsanleitung

Kohler

Kohler K-6813 Montageanleitung

Kohler

Kohler Electric Shower Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung