Kohler K-T16229 Bedienungsanleitung

Installation Guide

Concentric Thermostatic Trim

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-T16229

1066047-2-C

Tools and Materials

Before You Begin

CAUTION: Risk of personal injury. To eliminate the risk of

scalding, the water temperature should never be set above

120°F (49°C).

DANGER: Risk of scalding or other severe injury. Before

completing installation, the installer must set the maximum

water temperature setting of this valve to minimize the risks

associated with scalding hazards according to ASTM F 444.

CAUTION: Risk of scalding. This device has been calibrated

at the factory to ensure a safe maximum water temperature.

Any variance in settings or water inlet conditions from those

used during factory calibration may raise the discharge

temperature above the safe limit, and may present a scalding

hazard. Responsibility for installation and adjustment of this

device in accordance with these instructions lies with the

installer.

IMPORTANT! No minimum wall thickness is required if the wall

material is strong enough to support the trim. If the walls are less

than 1/2″(1.3 cm) thick, it is recommended reinforcement be added

to prevent the wall from ﬂexing when the trim is tightened. Flex in

the wall will result in improper front plate installation.

Observe all local plumbing and building codes.

Mounting Nut

Installation Tool

(Supplied with Valve) Temporary

Shut-Off

Knob

(Supplied with Valve)

Adhesive Caulk

or Sealant

1066047-2-C 2 Kohler Co.

Before You Begin (cont.)

The ﬁnished wall or bath/shower unit must be installed prior to

installing this trim.

IMPORTANT! If you are installing the trim to a valve in a

back-to-back installation, before beginning the installation you must

determine which of the valve supplies are reversed (hot water

routed to cold side and valve rotated 180°).

If the trim will be installed on a valve with a back-to-back

installation with another valve, follow the corresponding

directions.

The valve shuts off by water pressure. Do not force the handle in

any direction. To turn the valve off, gently turn it clockwise to the

″OFF″position.

IMPORTANT! There are a number of steps devoted to correctly

orienting various parts. The various components must be kept

correctly oriented throughout the installation, for ease of installation.

Shut off the main water supply.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

Kohler Co. 3 1066047-2-C

1. Determine the Wall Thickness

NOTE: The plaster guard must be in place for these steps.

NOTE: The ﬁnished wall must be installed before you perform these

steps.

NOTE: If the plaster guard is inside the ﬁnished wall, the wall is too

thick for the install and the valve needs to be moved forward.

NOTE: This trim is designed to allow for a 1-1/2″(3.8 cm) variation

in wall thickness.

Take a straight object such as a pencil and hold it along the

outside edge of the mud guard with the tip touching the ﬁnished

wall.

Either mark the spot where the top edge of the plaster guard and

the pencil meet or hold the pencil with your ﬁngers at that spot.

Move the pencil to the inside of the plaster guard. Touch the tip

of the pencil to the bottom of the plaster guard at the deepest

point next to the area labeled ″1.″

Plaster Guard

Ramp

Spacer

(Thin Wall)

Spacer

(Medium Wall) Spacers

(Thick Wall)

Ramp

Measure to finished

wall with stick or pen.

Max Finished Wall

Thickness

Finished

Wall

1066047-2-C 4 Kohler Co.

Determine the Wall Thickness (cont.)

If the mark on the pencil or your ﬁngers is even with the top

edge of the plaster guard or above it, go to the next section of

this installation.

If the mark or your ﬁnger is below the edge of the plaster

guard, perform the remaining steps:

Slide the pencil along the steps until the mark or your ﬁngers are

even with the top edge of the plaster guard.

Note which area of the plaster guard the pencil is touching.

If the pencil is touching the step labeled ″1,″you will need to

add 1 spacer.

If the pencil is touching the step labeled ″2,″you will need to

add 2 spacers.

Kohler Co. 5 1066047-2-C

2. Install the Spacers

Remove the plaster guard.

Cut or break the mounting nut tool out of the center of the

plaster guard.

If you do not need to add spacers go to the next section.

To Install the Spacer(s)

Align the slots on each spacer with the tabs on the valve.

Slide the spacer or spacers onto the valve.

You will hear and/or feel each spacer snap into place.

Mounting Nut

Installation Tool

Plaster Guard Temporary

Shut-Off Knob

Temperature Adapter

Extension

Tab

Slot

1066047-2-C 6 Kohler Co.

3. Install the Stem Extension

Turn the valve to the off position by turning the stem clockwise

using the temporary shut-off knob.

Determine the correct stem extension for your installation:

•If no spacers were needed, the stem already installed is correct.

•If 1 spacer was installed, remove the thin wall stem and install

the medium wall stem.

•If 2 spacers were installed, remove the thin wall stem and install

the thick wall stem.

•The spline adapter should come installed in the correct position.

If the spline adapter comes off when the stem is removed, it must

be reinstalled correctly.

•To reinstall the spline adapter, position it with the seam in the 7

o’clock position.

NOTE: The stem must be correctly aligned for the rest of the

installation steps.

Notch

45˚

Notch

Back-to-Back Installation

Normal Installation

Spline Adapter

Vertical

Stem

Screw

Stem & screw for thin wall

Stem & screw for medium thick wall

Stem & screw for thick wall

Vertical

Timing Mark

Kohler Co. 7 1066047-2-C

Install the Stem Extension (cont.)

Situate the timing mark at the 1 o’clock position. If the timing

mark is not aligned correctly, remove the stem and move it one

spline to reinstall it.

If the stem still does not align correctly, remove the stem and

remove the spline adapter, adjust it one spline, and reinstall it.

Repeat until the stem is perfectly aligned.

If the valve cartridge is ﬂipped (hot and cold inlets reversed),

install the stem with the timing mark in the 7 o’clock position.

Conﬁrm that the stem is correctly installed, with the timing mark

correctly positioned and the arms vertical and horizontal.

1066047-2-C 8 Kohler Co.

4. Install the Mounting Hub

Position the tab on the temperature adapter in the 6 o’clock

position.

Gently slide the mounting hub over the valve stem and into the

temperature adapter. The ″Up″imprint on the hub should be

situated in the 12 o’clock position.

Align the four slots in the hub base with the four tabs on the

temperature adapter. The coil can be turned to achieve the proper

alignment.

Firmly push the hub into place. There will be a noise as it snaps

into place.

Make sure all four slots are engaged.

Position the pin on the mounting hub assembly at approximately

the 7 o’clock position, directly above the ﬁrst tooth on the

mounting hub assembly.

Slot

Position tab of

temperature adapter

to 6o’clock position.

Position in approximately the

7o’clock position, directly

above the first tooth.

Temperature

Adapter

Mounting Hub

Assembly

First Tooth

Kohler Co. 9 1066047-2-C

5. Install the Mounting Plate

Turn the volume control stem clockwise to the ″Off″position

using the shut-off knob (or gently with a pliers).

Position the mounting plate over the mounting hub with the ″UP″

imprint in the 12 o’clock position.

NOTE: There are two threaded holes in close proximity to each

other in the valve. For this trim, make sure the screws are threaded

into the threaded holes in the corners of the valve.

Insert the screws through the slots in the mounting plate and

thread them into the valve.

Thread the screws in until they are almost tight, but loose enough

to allow the plate to be adjusted horizontally.

Align the marks on the mounting plate with the knobs on the

stem by sliding the mounting plate left or right as needed.

Fully tighten the mounting screws.

Apply a small amount of adhesive caulk or sealant to the top and

sides of the mounting plate.

Mounting Plate

Mounting Screw

Mark

Volume

Control Stem

Apply adhesive

caulk or sealant.

Temporary Shut-Off Knob

(Supplied with Valve)

1066047-2-C 10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Torsion Bedienungsanleitung

Kohler

Kohler K-17230T-DR Bedienungsanleitung

Kohler

Kohler K-11496X Montageanleitung

Kohler

Kohler K-3487 Bedienungsanleitung

Kohler

Kohler 74036T-4E2 Bedienungsanleitung

Kohler

Kohler Cantata K-2199 Bedienungsanleitung

Kohler

Kohler Avid T97367-4-BN Bedienungsanleitung

Kohler

Kohler Fairfax K-12265-4-BN Montageanleitung

Kohler

Kohler 76633T-B Bedienungsanleitung

Kohler

Kohler K-10088 Montageanleitung

Kohler

Kohler K-T16113 Bedienungsanleitung

Kohler

Kohler MARSTON K-2766 Bedienungsanleitung

Kohler

Kohler K-702-N1 Bedienungsanleitung

Kohler

Kohler K-6812 Bedienungsanleitung

Kohler

Kohler K-9310X Montageanleitung

Kohler

Kohler K1044435 Handbuch

Kohler

Kohler K-1154-HC Kurzanleitung

Kohler

Kohler K4915 Betriebsanleitung

Kohler

Kohler K-T15601 Bedienungsanleitung

Kohler

Kohler C3-455 Quiet-Close K-8298-CR Bedienungsanleitung

Kohler

Kohler K-2313 Bedienungsanleitung

Kohler

Kohler K-7323 Bedienungsanleitung

Kohler

Kohler Singulier 7787T-4 Bedienungsanleitung

Kohler

Kohler K-557-K Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung