Kohler MODERN LIFE K-21842T Bedienungsanleitung

-1-

INSTALLATION INSTRUCTIONS

TOUCHLESS FLOOR STANDING URINAL 3L

(3L)

K-21842T( )/K-21842T-C05( )

TOUCHLESS FLOOR STANDING W/ELECTROLYZED WATER 1L/AC

( ) (1L)

K-21842T-WEW

TOUCHLESS FLOOR STANDING W/ELECTROLYZED WATER 3L/AC

( ) (3L)

K-21842T-EW

TOUCHLESS FLOOR STANDING W/ELECTROLYZED WATER & IOT 1L/AC

( ) (1L)

K-21842T-WXEW

MODERN LIFE

Observe all local plumbing and building codes.

Carefully inspect the new urinal for damage.

Site preparation may require additional tools and

hardware.

Handle with care. Vitreous china can break

or chip if the product is handled carelessly.

CAUTION: Risk of personal injury or product

damage.

Please read these instructions carefully to familiarize

yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is based upon the

latest product information available at the time of

publication. Kohler China reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning, and

warranty information -

please leave instructions for the

consumer

Fixture dimensions are nominal and conform to tolerances

established by ASME Standards (A112.19.2-2018).

The product complies with GB/T 6952-2015.·

ASME (A112.19.2-

2018)

GB/T 6952-2015

BEFORE YOU BEGINBEFORE YOU BEGIN

2019

No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 528137

2 528137

8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA 256410

8 256410

NO.1 KOHLER STREET, ECONOMIC DEVELOPMENT ZONE OF FAKU COUNTY, SHENYANG LIAONING PROVINCE, PRC 110400

1 110400

POST CODE:

1356730-T01-B

Open end/adjustable wrenches

Tape measure

Basin wrench

Pipe wrench

Square

Level

Pliers

Socket wrench with sockets

Screw driver

Seal tape

Connection wire

Wire cutter

Insulation tape

Bushing

Drill

Sealant

RECOMMENDED TOOLS AND MATERIALS (NOT SUPPLIED)RECOMMENDED TOOLS AND MATERIALS (NOT SUPPLIED)

()

SPECIFICATIONS

Model

K-21842T(DC w/o Electrolyzed Water 3L)

K-21842T-C05(AC w/o Electrolyzed Water 3L)

K-21842T-WEW(AC with Electrolyzed Water 1L)

K-21842T-EW(AC with Electrolyzed Water 3L)

K-21842T-WXEW(w/Electrolyzed Water & IOT AC 1L)

Power

DC power unit 4 "AA" size alkaline batteries (Batteries For Largess)

AC/DC transformer input AC 220V 50/60Hz (Sold Separately)

AC/DC Switch Power input AC 220V 50/60Hz

Liter per flushing

Water pressure at 0.18~0.55 MPa: Average no more than 1L

Water pressure at 0.1 MPa: no more than 1L

Water pressure at 0.18~0.55 MPa: no more than 3L

Water pressure at 0.1 MPa: no more than 3L

Average

Temperature Environmental temperature: 1 to 55

Starting pressure 0.05Mpa~0.86MPa

Sensing distance 70 cm away from sensor

Testing time About 4 seconds

Flushing Mode Dual flushing (3L)

Flushing after used (1L)

Note: the sensing distance in the table is measured with a 30x30cm board as the reflecting surface.

Sterilized water (refers to the tap water containing hypochlorite generated by chlorine ions after ionization): wash bowl

surface by sterilized water generated within working cycle, reduce bacteria growth on the urinal surface.

Different water quality might cause different sterilization effect.

K-21842T-WXEW contains a wireless transmission module with the model approval code: CMIIT ID:2018DP2230.

-2-

1356730-T01-B

30x30cm

K-21842T-WXEW CMIIT ID:2018DP2230

K-21842T ( ) (3L)

K-21842T-C05 ( ) (3L)

K-21842T-WEW( ) ( ) ( ) (1L)

K-21842T-EW( ) ( ) ( ) (3L)

K-21842T-WXEW( ) ( ) ( ) ( ) ( ) (1L)

4 5 (AA 4)

220V AC 50/60Hz

0.18~0.55MPa 1L

0.1MPa 1L

0.18~0.55MPa 3L

0.1MPa 3L

155

0.05Mpa~0.86MPa

70cm

(3L)

(1L)

-3-

ROUGHING-IN

Unit:mm

Reference Value

Kohler reserves the right to change marked dimensions without prior notice.

*Recommended dimensions for installation only, please

adjust according to actual situation.

Tap

Wall

Floor

Fig.1

100

255

800*

545*

Supply

150*1008

330

406 319

1356730-T01-B

-4-

(

)

NOTE:

For Retrofit Installations

For New Installations

If a pre-existing waste pipe will be used and will result

in an acceptable rim height (refer to the rough-in dimensions),

follow the retrofit installation instructions.

Turn the water supply line off, remove the existing urinal,

then cap off the water supply line inside the wall.

Install waste pipe as necessary to conform to the

roughing-in dimensions.

Fig.2

PREPARE THE SITEPREPARE THE SITE

Draw lines

according to

the template.

110mm Drain pipe

110mm

Finished Wall

150*

Draw centerline.

Draw lines according

to height of the

mounting hole center.

Connect the right

and left lines. Drill

holes on the center.

Electronic components are pre-installed in factory.

Electronic Components InstallationElectronic Components Installation

800

No object within 800mm of the

width of the sensor bilateral symmetry

800mm

No objects in the

Sensor before

1000mm

Clapboard suggest

reference length is 450mm

450mm

450

1000

Notice: To ensure an effective flush performance,

strongly recommended inner diameter of

water supply (including water meter, valve,

etc.) is no less than 25mm, and supplied

water pressure (sensor inlet dynamic

pressure) is 0.18MPa ~0.55MPa.

(

) 25mm (

) 0.18MPa ~0.55MPa

1356730-T01-B

INSTALLATION

Install and uninstall the sensor controller

a. Install the sensor controller box.

b. Install the screw.

c. Connect the sensor wire.

Install and uninstall the Fixture, Valve

Assembly

Unscrew the screws on the Fixture, Valve Assembly. Remove

the Fixture, Valve Assembly from the urinal by moving it.

-5-

Install DC Power Unit

1. Take out battery case assy., and loosen the screws (17).

Place 4 AA batteries into the battery case according to

negative and positive electrode marks on the battery case

cover (18). Tighten the screws on the battery case cover

(18).

do not mistake the battery electrodes, and do not

use the new and used batteries together.

2. Then insert the battery pack in the battery box bracket,

connect each colored connector to the corresponding

connector of the same color.

NOTE:

1. (17) (18)

4 5 (18) (17)

Fig.3

Install

Battery Box Asm

Bracket, Valve Asm

Control Box Asm

1356730-T01-B

-6-

Power Connection

1. Please directly reference to install DC Power Unit when

installing K- 21842T (DC).

2. Please match K-16305T-NA AC power unit when installing

K-21842T-C05. The way of installation is as below:

1. K- 21842T

2. K-21842T-C05 K-16305T-NA

CAUTION:

a. Do not connect 220V AC Power supply to DC wiring

terminal.

b. Do not damage the covering of AC power unit or

remove screws to avoid leakage.

c. Outlet of AC power unit upward prohibited.

A. Fig.6: AC power unit connect way:

AC power unit is connected to electric control box by

connection wire.

a. 220V

A. 6

Fig.4

Connector

Wire prepared

by customer

Connector

Connect with the same color wire,

and protect connect area by insulation tape.

16305T-NA

AC Power Unit

Control Box Assy. Outlet Downwards

Outlet Upwards

Connect to

Sensor

Connect to

Sensor

Connect to AC

Power Supply

Connect to AC

Power Supply

B. When installing the power uint in the bracket, please layout

bushing according to Fig.5 and thread wire through the

bushing.

Fig.5: Connection sketch while installing power uint in the

bracket.

One AC power unit can supply one

sensors at most.

CAUTION:

Fig.5

AC Power Unit

AC Power

Install in

the bracket

Bracket

Control Box Asm

Bushing

600 602

1356730-T01-B

-7-

3. AC/DC Switch Power connect way

(for K-21842T-WEW/K-

21842T-EW/K-21842T-WXEW)

3. (K-21842T-WEW/K-21842T-EW/K-

21842T-WXEW )

Control Box

Connector

Switch Power

Fig.6

Notice:

a. Keep the connector away from water.

b. Don't mistake the direction of inlet and outlet.

c. Do not connect the DC output of AC power unit to AC

power supply.

d. Do not connect to power supply while installing.

Connection line is not supplied. AC connection wire with

insulating sleeving is recommended. Wire of which the

nominal section area of conductor is not less than 0.5mm

is also recommend. DC connection line use wire of which

the nominal section area is not less than 0.3mm . It is cut

according to acted installation requirements (The length of

cut wire is recommended less than10m).

e. The head AC power supply must be protected with

appropriate fuse.

f. Please confirm the AC power supply and water supply

should be shut off before maintaining the products with AC

power related.

0.5mm

0.3mm

10m

Install urinal

1. Check the regulator, see Fig.7. 1. 7

Fig.7

Back of Urinal

Regulator

Nozzle

1356730-T01-B

-8-

2. Connect inlet pipe: Connect to the corner valve.

3. Install flange (see Fig.8, optional for purchase). Put the

urinal against wall and align the bottom with the lines

drawn.

4. Insert the screw through the screw hole (see Fig.9) Into the

L-shaped fixing block. Tighten the screw.

5. Apply silicone sealant between the urinal and the wall.

3. ( 8 )

4. ( 9) L

Fig.9

Fig.8

Flange

Screw Hole

Install Urinal Cover

See Fig.#10

NOTE:

CAUTION:

1. Open urinal cover lock package and remove contents. Fix

hook and screw as shown.

2. Put urinal cover on the urinal.

3. Use supplied locking tool to install and tighten the screw.

4. Check that the urinal cover is properly locked.

Using a 5/8" wrench, assemble and tighen nut,

washer and lock nut on both sides of urinal.

Risk of chipping or breaking urinal. Do not

overtighen screws on urinal.

5/8"

Hook

Nut

Washer

Screw

Sleeve

Fig.10

1356730-T01-B

Fig.#11

Install fragrance porcelain

(for K-21842T-WXEW only)

1. Insert the scent top into the plug.

2. Take out the tube. Fill fragrance into

the tube. Do not overfill to avoid

overflow.

3. Insert the plug into the tube.

4. Insert the tube into the hole on the

urinal cover.

Be careful when filling

fragrance into the tube. Do not drop it

onto the electrical components to

avoid short circuit and malfunction.

Caution:

(

K-21842T-WXEW)

Notice: The first 2 minutes with power is the standby time for

adjusting sensing distance. Persons or subjects

should avoid standing before the sensor (See Fig.2).

The sensor will not flush during.

(2)

USER'S GUIDEUSER'S GUIDE

Electrolyzed Water

The urinal will take a flush Electrolyzed Water every two

hours. If the urinal is used during flushing, the electrolysed

water will stop.

Deodorizing Flushing

The urinal will take a flush automatically when it's used 3 or 4

times in 2 minutes.

Replacement of Batteries

When the batteries run out, please remove the Battery Box

Assembly by following the battery installation steps and then

replace the batteries.

2 3-4

-9-

MAINTENANCE

Clean the Filter Screen

If the flushing volume reclines sharply after installation or

used for a long time with no cause from water pressure, the

filter may need a wash. Please operate as following steps:

Remove the fixed cap

a. Turn off the water supply and power

supply before cleaning the filter.

b. Avoid damaging or losing the filter during

cleaning.

Caution:

and take out the filter, clean the filter

and then reinstall it.

Filter

Fixed Cap

Fig.12

1356730-T01-B

-10-

TROUBLESHOOTING

No flushing

1. No power or mistake connected.

2. Out of electricity.

3. Sensor no working.

1. Check the power connect.

2. Replace batteries.

3. Check connector connect or Replace

sensor.

No flashing

Light indicator no bright

Buzzer alarm

1. The small hole of valve core is blocked.

2. The filter of valve core is blocked.

1. No power or mistake connected.

2. Position Light broken.

1. Out of electricity(the buzzer will sound every 2s).

2. Battery low voltage(the buzzer will sound every

6s).

1. Clean the small hole of valve core with

thin steel wire.

2. Wash the filter of valve core with a brush.

1. Check the power connect.

2. Replace Light indicator.

1. Replace batteries.

2. Replace batteries.

Please make following checks before repair:

Symptoms Probable causes Corrective actions

No flushing or poor

flushing

1. Adjusting bolt not fully open

2. Low water pressure.

3. Filter is obstructed.

1. Open the adjusting bolt.

2. Improve water supply.

3. Clean the filter.

1. 2s

2. 6s

IMPORTANT CONSUMER INFORMATION

CONSUMER RESPONSIBILITIES

Do not directly flush the sensor with water. The sensor is an

electronic instrument.

Keep the sensor clean.

Do not use eradicator, abrasive powder or oil, acid or alkali

liquid detergent.

Do not spray air freshener, disinfectant or other kinds of

odious removing, cleaning organic liquid to the sensor directly.

Urinal is designed for use with potable water.

Avoid water that includes a lot of contaminants or acid/lakali

water and impure water.

When AC power unit is connected to 220V AC power supply,

corresponding protective measures should be taken.

Please confirm no water penetration at the connection area of

AC wire, and the connection area is not easy to be affected

by damp.

220V

1356730-T01-B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-10094 Montageanleitung

Kohler

Kohler K-97060-4-CP Bedienungsanleitung

Kohler

Kohler Discovery Bedienungsanleitung

Kohler

Kohler K-7702 Bedienungsanleitung

Kohler

Kohler K-8801 Montageanleitung

Kohler

Kohler K-2529 Montageanleitung

Kohler

Kohler K-1997 Montageanleitung

Kohler

Kohler Antique K-100 Montageanleitung

Kohler

Kohler K-18485 Montageanleitung

Kohler

Kohler Castia K-TS35917-4Y-2MB Bedienungsanleitung

Kohler

Kohler Singulier 10861-4ND Bedienungsanleitung

Kohler

Kohler K-454 Montageanleitung

Kohler

Kohler K-T395 Montageanleitung

Kohler

Kohler K-16012-4 Bedienungsanleitung

Kohler

Kohler Karbon K-6227D Bedienungsanleitung

Kohler

Kohler K-2219 Bedienungsanleitung

Kohler

Kohler K-2313 Bedienungsanleitung

Kohler

Kohler K-6814 Montageanleitung

Kohler

Kohler K-7259 Montageanleitung

Kohler

Kohler K-1107 Bedienungsanleitung

Kohler

Kohler K-19537P-7 Montageanleitung

Kohler

Kohler K-19909 Montageanleitung

Kohler

Kohler K-158 Bedienungsanleitung

Kohler

Kohler Electric Shower Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung